This commit introduces a bare-bones replacement for libsystemd:
- Build .so file and add --with-libsystemd to configure
- Add capabilities support to test/src/serv.c
- Update tests to account for a Finit built w/o libsystemd support
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
We cannot rely on the auto-detection of Bash completion dir during 'make
distcheck' because autotools does not use DESTDIR, only --prefix for the
install check, and pkg-config returns a system path.
Also, show detected path in configure summary for debug.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This change adds very basic tmpfiles.d/ support to Finit. Much of the
basic types are supported, but not all, so for now, please check the
code for details on what is working.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
This adds support for bringing up the system with an alternate fstab at
boot. E.g., when using a primary/secondary setup for boot partitions.
By default /etc/fstab is read, like before, this can now be changed
using configure --with-fstab=/path/to/fstab.primary, which sets the
default that can be overridden using finit.fstab=/etc/fstab.secondary
If mounting, or fsck, fails in any way, Finit calls its own bundled
sulogin, or the system sulogin(8), to let the user handle the issue.
If there is no sulogin available, Finit will try to start up in its
rescue.conf boot mode.
Please note, in either of these rescue modes, use `reboot -f` to get the
system to reboot. Finit is on pause in the background in rescue mode
and cannot be relied on (since there may not be any writable filesystems
available.).
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Planned changes will directly change the behavior of conditions, and
instead of having to implement compatibility wrappers and further
complicate the code, we've taken the decision to go for v4 directly.
This allows us to also rip out the complex inetd support.
Other changes in this commit:
- Revert back to .tar.gz distribution archives, by popular demand
- Add .sha256 checksum for .tar.gz archive
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
In massively parallel builds we've seen finit fail in the install phase
of the contrib section with:
ln: failed to create symbolic link '/home/bob/jenkins/workspace/WeOS-feature_5.x_igmp-mld-snooping/staging/share/doc/finit/contrib/alpine/finit.d/getty.conf': No such file or directory
ln: failed to create symbolic link '/home/bob/jenkins/workspace/WeOS-feature_5.x_igmp-mld-snooping/staging/share/doc/finit/contrib/alpine/finit.d/keymap.conf': No such file or directory
ln: failed to create symbolic link '/home/bob/jenkins/workspace/WeOS-feature_5.x_igmp-mld-snooping/staging/share/doc/finit/contrib/alpine/finit.d/modules.conf': No such file or directory
ln: failed to create symbolic link '/home/bob/jenkins/workspace/WeOS-feature_5.x_igmp-mld-snooping/staging/share/doc/finit/contrib/alpine/finit.d/klogd.conf': No such file or directory
ln: failed to create symbolic link '/home/bob/jenkins/workspace/WeOS-feature_5.x_igmp-mld-snooping/staging/share/doc/finit/contrib/alpine/finit.d/syslogd.conf': No such file or directory
This patch is a countermeasure since fixing the root cause may take a
while (to be prioritized).
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
This patch adds a simple but effective watchdog daemon with support for
handover to an external daemon, should one register using the API.
Disabled by default, enable by:
configure --enable-watchdog
The watchdog forks to the background, opening /dev/watchdog setting a
three second timeout, and kicking every second. At shutdown/reboot the
daemon will receive SIGPWR from Finit to exit and cause a WDT reboot.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
This patch adds initial support for handling MD RAID arrays. Adding
a pass at the very end of the shutdown sequence to signal any external
RAID controller to clear its state before we proceed to halt/reboot.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
This patch adds support for a more fine grained approach to what
filesystems are unmounted at shutdown/reboot. This so we later
can add support for `mdadm --wait-clean --scan`, which relies on
/proc, /sys, and /dev being there before we call reboot().
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
The TTY handling in Finit has always been a bit of a patch work. This
commit is an attempt at a first cleanup and simplification.
Included is a brand new built-in getty which should work fine on both
virtual and serial consoles. It is however completely untested on the
latter serial consoles.
Still TODO: add support for /etc/securetty, add support for actually
setting TERM when calling /bin/login.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
This patch fixes regressions in --enable-static introduced with the
conversion to the GNU configure and build system.
The default link flag to libtool is set to -static-libtool-libs, meaning
not a fully static build -- the C library will still be used as an .so
which is usually what people want -- whereas libite (-lite) and libuEv
are linked statically.
$ ldd /sbin/finit /sbin/initctl
/sbin/finit:
linux-vdso.so.1 => (0x00007ffffde62000)
libc.so.6 => /lib/x86_64-linux-gnu/libc.so.6 (0x00007f6979ad8000)
/lib64/ld-linux-x86-64.so.2 (0x000055d893e96000)
/sbin/initctl:
linux-vdso.so.1 => (0x00007ffed0dd6000)
libc.so.6 => /lib/x86_64-linux-gnu/libc.so.6 (0x00007feb3a29c000)
/lib64/ld-linux-x86-64.so.2 (0x00005556ebd2b000)
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
Finit <3 did not use GNU configure and build system. This patch adds an
install-dev rule that is used by some to install required headers for
external plugin developers.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
From now on the user is required to have libuEv and libite installed
before building and installing finit. This is for maintenance reasons.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
Joachim Wiberg