Adjust debug levels slightly and add _w() macro for LOG_WARNING,
useful when having /dev/kmsg as backend. The latter outputs any
log <= LOG_ERR to console as well.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
The new logit() function takes care to print to stderr if syslogd has
not yet started. The _d(), _e(), and _pe() macros have an additional
requirement: to always print on stderr.
After the boot we also want to see what happned during, so this patch
simply adds syslog() support to _d(), _e(), and _pe().
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
This patch removes internal logging macros and adds support for logging
to stderr until a syslogd is up and running, i.e. /dev/log appears.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
This patch adds initial support for handling MD RAID arrays. Adding
a pass at the very end of the shutdown sequence to signal any external
RAID controller to clear its state before we proceed to halt/reboot.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
This patch adds support for the following /etc/fstab API's on systems
that do not have them, e.g. musl libc on Alpine Linux.
- setfsent()
- getfsent(), and
- endfsent()
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
The TTY handling in Finit has always been a bit of a patch work. This
commit is an attempt at a first cleanup and simplification.
Included is a brand new built-in getty which should work fine on both
virtual and serial consoles. It is however completely untested on the
latter serial consoles.
Still TODO: add support for /etc/securetty, add support for actually
setting TERM when calling /bin/login.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
This patch adds prototype support for the Debian/Ubuntu/Busybox network
configuration file /etc/netork/interfaces. If this file exists Finit
will call `ifup` for each (non-commented-out) interface marked `auto`.
With this implementation we block boot until all ifup commands have
returned, which is less than ideal. A better approach would be to ifup
only loopback and create deferred tasklets to be run in parallel with
the rest of the boot.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
This patch fixes a long standing problem with TTY's. The original code
tried to workaround a limitation in the console of some embedded systems
that was detrimental on actual TTYs.
As an added benefit, the console specific "Press Enter" prompt for the
console port is now available on all TTYs -- meaning no getty needs to
be started and kept needlessly in the background until it is needed.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
The tempfile() replacement in Finit leaked temporary files in /tmp.
The mkstemp() based implementation does not remove temporary files
when they are closed.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
This patch makes it possible to communicate process name or JOB[:ID]
from initctl to Finit. When the process name translates into a service
with multiple instances Finit applies the requested command to all
instances. For example, two Dropbear SSH services running on two
different ports, calling `initctl stop dropbear` stops both services.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
- Reduce size of `helpers.c`, for linking against new `initctl` tool,
by moving out functions to `pid.c` and `exec.c`
- Add `AF_UNIX` API to Finit, to complement old `/dev/initctl` FIFO
- Let old FIFO API be used by init/telinit: `init <q | 1-9>`
- Move all advanced initctl code from `client.c` to `initctl.c`, yes
its a bit confusing to call the *new* tool the same as the old FIFO
but this is more in line with what, e.g Upstart does.
- Move all advanced server side code from `plugins/initctl.c` to `api.c`
- Update TODO with upcoming inetd syntax change and dynamic events.
- Temporarily fix display of inetd services from `initctl status -v`
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
Further refactoring of the client code. Supported commands:
- debug: Toggle PID 1 debug flag
- version: Show Finit version or custom header string
- reload: Reload config files in /etc/finit.d/, same as SIGHUP
Also supported is the legacy 'init q' command, to reload config.
The 'status' command now supports an optiona '-v', either as an
argument to init itself, or as argument to the command. When it
is given 'status' lists verbose information about all services.
Currently only the service arguments are listed.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
This patch adds support for starting and supervising multiple
services (run, task, or service) using an extra #ID number.
service #1 [2345] /sbin/httpd -f -h /http -p 80 -- Web server
service #2 [2345] /sbin/httpd -f -h /http -p 8080 -- Old web server
Also included in this patch is a fix for endless respawn of faulty
services. For instance, a buggy daemon that crashes repeatedly will now
be stopped after 10 respawns.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
Add support for runlevels to tty command and support for reading baud
rate and TERM variable from finit.conf.
The tty-watcher thread has been converted to a standard I/O plugin.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
Most systems need an early bootstrap phase for one-shot tasks and
necessary one-time probing. This phase usually runs well before any
networking is setup. This commit adds support for that 'S' runlevel,
and also extends the number of possible total runlevels to nine.
For the one-shot tasks that run in bootstrap two new finit.conf cmds
have been added:
- task: For one-shot tasks that can be started in parallell
- run: For one-shot tasks that must run in sequence
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
- Remove indentation of module loading and device node creation
- Clarify that we load kernel modules
- Clarify that we load Finit plugins
- Remove cls()
- Remove verbose condition for echo()
- Make banner a separate function with optional distribution banner
- Add a few neat ANSI escape sequences for cls(), clreol(), delline(), etc.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
This also adds support for monitor /dev for TTYs appering after boot,
USB-to-serial converters for example.
Some limitations: Baudrate (and other settings) is hardcoded for now,
should be read from config file.
The run_parts() implementation used variable arguments in a bad way,
resulting in it not working properly. Replaced va_*() code with a
simple cmd argument that's passed to each script called.
Also, the opendir()/readdir() code has been replaced with scandir()
using regular alphasort(). This simplifies the code somewhat as well.
Otherwise, minor cleanups.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
This was missing from the 1.4 release due to it being hidden in one
of my private plugins. Sorry!
Also, add another log macro. Warnings are quite useful things to have.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
Restructure start by calling the plugin loader earlier. This makes it
possible to run hooks even earlier. This also adds a new hook:
HOOK_ROOTFS_UP which runs as soon as the system root (/) is available.
Another very notable change is the slow refactor of helpers.c into a finit
helper library called libite.so (-lite). This is a light-weight
Also, lots of misc. fixes all over the place. Signal handling still really
needs to be looked into once more!
Makefile:
Add dependency handling for parallell build
Add libite library
ChangeLog:
Update with new 1.4 release. There is a lot of fixes!
libite/:
Collection of utility functions and C library extensions for
finit & its plugins
reboot.c:
New reboot tool. Simply sends SIGINT to PID 1
finit.h:
Cleanup old LISTEN_INITCTL define, code is in an optional plugin now
finit.c:
Let mdev/udev run *after* cls()
Add useful debug statement for /proc/cmdline
Earlier plugin load => new early hook point
Show OK/FAIL for total plugin load, not for each plugin => speedup
helpers.h:
Rename syslog macros to prevent common name clashes (DEBUG/ERROR)
Add __FILE__ to _e(), _d() and _pe() macros
helpers.c:
In ifconfig() the addr and mask arguments are now optional
The copyfile() has been moved to libite.so
Temporarily remove const directive from some functions to build
Use DFLSIG() macro in run_getty() to simplify code
plugin.h:
Add new HOOK_ROOTFS_UP hook
plugin.c:
Fix init_plugins() to actually register the plugin's I/O fd
Skip verbose listing of all plugins in plugin_load_all()
svc.c:
svc_start(): Dito
plugins/Makefile:
Inherit CFLAGS and LDFLAGS, but make sure to filter out -rdynamic
from LDFLAGS, it's used by the daemon, only
plugins/initctl.c:
New includes after helpers.h refactor
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
Improve upon API names, both internal and external, to make it clearer
where methods are located and clarify responsibility.
Add new Makefile target "dev" to create untagged development snapshots.
Bump version for upcoming release.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
Move utility macros from finit.h to helpers.h and continue refactoring
and streamlining of public plugin API.
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
Joachim Nilsson