Finit: Fast Init * [Introduction](#introduction) * [Features](#features) * [Bootstrap](docs/bootstrap.md#bootstrap) * [Runlevels](#runlevels) * [Syntax](docs/config.md#syntax) * [Inetd](docs/inetd.md#inetd) * [Runparts & /etc/rc.local](#runparts--etcrclocal) * [Hooks, Callbacks & Plugins](docs/plugins.md#hooks-callbacks--plugins) * [Rebooting & Halting](#rebooting--halting) * [Commands & Status](#commands--status) * [Tips & Tricks with the kernel cmdline](docs/cmdline.md) * [Building](docs/build.md#building) * [Running](docs/build.md#running) * [Recovery](docs/build.md#recovery) * [Debugging](docs/build.md#debugging) * [Requirements](#requirements) * [Origin & References](#origin--references) Introduction ------------ [![License Badge][]][License] [![Travis Status]][Travis] [![Coverity Status]][Coverity Scan] Finit is a simple alternative to [SysV init][4] and [systemd][6]. It was reverse engineered from the [EeePC fastinit][] ten years ago by [Claudio Matsuoka][] — "gaps filled with frog DNA …" Focus is on small and embedded systems, although Finit is fully usable on server and desktop systems as well. For working examples, see the [contrib/](contrib/) section where both [Debian](contrib/debian/) and up to date [Alpine Linux](contrib/alpine/) tutorials can be found. ![Alpine screenshot](images/alpine-screenshot.png) The screenshot shows [Alpine Linux](https://www.alpinelinux.org/). Example ------- This example `/etc/finit.conf` can also be split up in multiple `.conf` files in `/etc/finit.d`. Available, but not yet enabled, services can be placed in `/etc/finit.d/available` and enabled by an operator using the [initctl](#commands--status) tool. ```ApacheConf # Fallback if /etc/hostname is missing host default # Runlevel to start after bootstrap, 'S', default: 2 runlevel 2 # Max file size for each log file: 100 kiB, rotate max 4 copies: # log => log.1 => log.2.gz => log.3.gz => log.4.gz log size=100k count=4 # Services to be monitored and respawned as needed service [S12345] /sbin/watchdogd -L -f -- System watchdog daemon service [S12345] /sbin/syslogd -n -b 3 -D -- System log daemon service [S12345] /sbin/klogd -n -- Kernel log daemon service [2345] /sbin/lldpd -d -c -M1 -H0 -i -- LLDP daemon (IEEE 802.1ab) # The BusyBox ntpd does not use syslog when running in the foreground # So we use this trick to redirect stdout/stderr to a log file. The # log file is rotated with the above settings. The condition declares # a dependency on a system default route (gateway) to be set. A single # at the beginning means ntpd does not respect SIGHUP for restart. service [2345] log:/var/log/ntpd.log /sbin/ntpd -n -l -I eth0 -- NTP daemon # For multiple instances of the same service, add :ID somewhere between # the service/run/task keyword and the command. service :1 [2345] /sbin/merecat -n -p 80 /var/www -- Web server service :2 [2345] /sbin/merecat -n -p 8080 /var/www -- Old web server # Alternative method instead of below runparts, can also use /etc/rc.local #task [S] /etc/init.d/keyboard-setup start -- Setting up preliminary keymap #task [S] /etc/init.d/acpid start -- Starting ACPI Daemon #task [S] /etc/init.d/kbd start -- Preparing console # Inetd services to start on demand, with alternate ports and filtering inetd ftp/tcp nowait [2345] /sbin/in.ftpd -- FTP daemon inetd tftp/udp wait [2345] /sbin/in.tftpd -- TFTP daemon inetd time/udp wait [2345] internal -- UNIX rdate service inetd time/tcp nowait [2345] internal -- UNIX rdate service inetd 3737/tcp nowait [2345] internal.time -- UNIX rdate service inetd telnet/tcp nowait [2345] /sbin/telnetd -i -F -- Telnet daemon inetd 2323/tcp nowait [2345] /sbin/telnetd -i -F -- Telnet daemon inetd 222/tcp@eth0 nowait [2345] /sbin/dropbear -i -R -F -- SSH service inetd ssh/tcp@*,!eth0 nowait [2345] /sbin/dropbear -i -R -F -- SSH service # Run start scripts from this directory # runparts /etc/start.d # Virtual consoles run BusyBox getty tty [12345] /sbin/getty -L 115200 /dev/tty1 linux tty [12345] /sbin/getty -L 115200 /dev/tty2 linux tty [12345] /sbin/getty -L 115200 /dev/tty3 linux # Use built-in getty for serial port and USB serial tty [12345] /dev/ttyAMA0 115200 noclear nowait tty [12345] /dev/ttyUSB0 115200 noclear # Just give me a shell, I need to debug this embedded system! tty [12345] @console noclear nologin ``` The `service` stanza, as well as `task`, `run`, `inetd` and others are described in full in [docs/config.md](docs/config.md). Here's a quick overview of some of the most common components needed to start a UNIX daemon: ``` service [LVLS] /path/to/daemon ARGS -- Some text ^ ^ ^ ^ ^ ^ | | | | | `-- Optional description | | | | `---------- Daemon arguments | | | `-------------------------- Path to daemon | | `--------------------------------- Optional conditions | `---------------------------------------- Optional Runlevels `------------------------------------------------ Monitored application ``` Some components are optional: runlevel(s), condition(s) and description, making it easy to create simple start scripts and still possible for more advanced uses as well: service /usr/sbin/sshd -D Dependencies are handled using [conditions](docs/conditions.md). One of the most common conditions is to wait for basic networking to become available: service /usr/sbin/nginx -- High performace HTTP server Here is another example where we instruct Finit to not start BusyBox `ntpd` until `syslogd` has started properly. Finit waits for `syslogd` to create its PID file, by default `/var/run/syslogd.pid`. service [2345] log /usr/sbin/ntpd -n -N -p pool.ntp.org service [S12345] /sbin/syslogd -n -- Syslog daemon Notice the `log` keyword, BusyBox `ntpd` uses `stderr` for logging when run in the foreground. With `log` Finit redirects `stdout` + `stderr` to the system log daemon using the command line `logger(1)` tool. A service, or task, can have multiple dependencies listed. Here we wait for *both* `syslogd` to have started and basic networking to be up: service [2345] log /usr/sbin/ntpd -n -N -p pool.ntp.org If either condition fails, e.g. loss of networking, `ntpd` is stopped and as soon as it comes back up again `ntpd` is restarted automatically. **Note:** Make sure daemons *do not* fork and detach themselves from the controlling TTY, usually an `-n` or `-f` flag, or `-D` as in the case of OpenSSH above. If it detaches itself, Finit cannot monitor it and will instead try to restart it. Features -------- **Process Supervision** Start, monitor and restart services should they fail. **Inetd** Finit comes with a built-in [inetd server](docs/inetd.md). No need to maintain a separate config file for services that you want to start on demand. All inetd services started can be filtered per port and inbound interface, reducing the need for a full blown firewall. Built-in optional inetd services: - echo [RFC862][] - chargen [RFC864][] - daytime [RFC867][] - discard [RFC863][] - time (rdate) [RFC868][] For more information, see [docs/inetd.md](docs/inetd.md). **Getty** Finit supports external getty but also comes with a limited built-in Getty, useful for really small systems. A getty sets up the TTY and waits for user input before handing over to `/bin/login`, which is responsible for handling the actual authentication. ```conf tty [12345] /dev/tty1 38400 nowait linux tty [12345] /dev/ttyAMA0 115200 noclear vt100 tty [12345] /sbin/getty -L 115200 /dev/ttyAMA0 vt100 ``` Users of embedded systems may want to enable automatic serial console with the special `@console` device. This works regardless weather the system uses `ttyS0`, `ttyAMA0`, `ttyMXC0`, or anything else. Finit figures it out by querying sysfs: `/sys/class/tty/console/active`. ```conf tty [12345] @console 115200 linux noclear ``` Notice the optional `noclear`, `nowait`, and `nologin` flags. The latter is for skipping the login process entirely. For more information, see [docs/config.md](docs/config.md#syntax). **Runlevels** Support for SysV init-style [runlevels][5] is available, in the same minimal style as everything else in Finit. The `[2345]` syntax can be applied to service, task, run, inetd, and TTY stanzas. Reserved runlevels are 0 and 6, halt and reboot, respectively just like SysV init. Runlevel 1 can be configured freely, but is recommended to be kept as the system single-user runlevel since Finit will not start networking here. The configured `runlevel NUM` from `/etc/finit.conf` is what Finit changes to after bootstrap, unless 'single' (or 'S') is given on the kernel cmdline, in which case runlevel 1 is started. All services in runlevel S(0) are started first, followed by the desired run-time runlevel. Run tasks in runlevel S can be started in sequence by using `run [S] cmd`. Changing runlevels at runtime is done like any other init, e.g. init 4, but also using the more advanced `intictl` tool. **Plugins** Plugins can *extend* the functionality of Finit and *hook into* the different stages of the boot process and at runtime. Plugins are written in C and compiled into a dynamic library loaded automatically by finit at boot. A basic set of plugins are bundled in the `plugins/` directory. Capabilities: - **Hooks** Hook into the boot at predefined points to extend Finit - **I/O** Listen to external events and control Finit behavior/services - **Inetd** Extend Finit with internal inetd services, for an example, see `plugins/time.c` Extensions and functionality not purely related to what an `/sbin/init` needs to start a system are available as a set of plugins that either hook into the boot process or respond to various I/O. For more information, see [docs/plugins.md](docs/plugins.md). **Progress** Finit prior to v3.0 showed the progress at boot: plugins and modules being loaded, run/tasks/services being started, etc. By default Finit is now silent, but progress can still be enabled at build-time using: configure --enable-progress or at boot from the kernel cmdline using the boot parameter `splash`: ```shell append="init=/sbin/finit splash" ``` For a really nice boot, add `quiet` as well. This silences the output from the kernel, leaving only warnings and errors. For other kernel command line parameters, see [docs/build.md](docs/build.md#recovery). Runparts & /etc/rc.local ------------------------ At the end of the boot, when all bootstrap (`S`) tasks and services have started, but not networking, Finit calls its built-in [run-parts(8)][] command on any configured `runparts ` directory. This happens just before changing to the configured runlevel (default 2). (Networking is enabled just prior to changing from single user mode.) ```shell runparts /etc/rc.d/ ``` Right after the runlevel change when all services have started properly, `/etc/rc.local` is called. No configuration stanza in `/etc/finit.conf` is required for `rc.local`. If it exists and is an executable shell script Finit calls it at the very end of the boot, before calling the `HOOK_SYSTEM_UP`. See more on hooks in [docs/plugins.md](docs/plugins.md#hooks), and about the system bootstrap in [docs/bootstrap.md](docs/bootstrap.md). Runlevels --------- Basic support for [runlevels][5] is included in Finit from v1.8. By default all services, tasks, run commands and TTYs listed without a set of runlevels get a default set `[234]` assigned. The default runlevel after boot is 2. Finit supports runlevels 0-9, and S, with 0 reserved for halt, 6 reboot and S for services to only run at bootstrap. Runlevel 1 is the single user level, where usually no networking is enabled. In Finit this is more of a policy for the user to define. Normally only runlevels 1-6 are used, and even more commonly, only the default runlevel is used. To specify an allowed set of runlevels for a `service`, `run` command, `task`, or `tty`, add `[NNN]` to your `/etc/finit.conf`, like this: ``` service [S12345] /sbin/syslogd -n -x -- System log daemon run [S] /etc/init.d/acpid start -- Starting ACPI Daemon task [S] /etc/init.d/kbd start -- Preparing console service [S12345] /sbin/klogd -n -x -- Kernel log daemon tty [12345] /dev/tty1 tty [2] /dev/tty2 tty [2] /dev/tty3 tty [2] /dev/tty4 tty [2] /dev/tty5 tty [2] /dev/tty6 ``` In this example syslogd is first started, in parallel, and then acpid is called using a conventional SysV init script. It is called with the run command, meaning the following task command to start the kbd script is not called until the acpid init script has fully completed. Then the keyboard setup script is called in parallel with klogd as a monitored service. Again, tasks and services are started in parallel, while run commands are called in the order listed and subsequent commands are not started until a run command has completed. Also, task and run commands are run in a shell, so pipes and redirects can be used. The following examples illustrate this. Bootstrap task and run commands are also removed when they have completed, `initctl show` will not list them. ``` task [S] echo "foo" | cat >/tmp/bar run [S] echo "$HOME" >/tmp/secret ``` Switching between runlevels can be done by calling init with a single argument, e.g. init 5, or using `initctl runlevel 5`, both switch to runlevel 5. When changing runlevels Finit also automatically reloads all `.conf` files in the `/etc/finit.d/` directory. So if you want to set a new system config, switch to runlevel 1, change all config files in the system, and touch all `.conf` files in `/etc/finit.d` before switching back to the previous runlevel again — that way Finit can both stop old services and start any new ones for you, without rebooting the system. Rebooting & Halting ------------------- Traditionally, rebooting and halting a UNIX system is done by changing its runlevel. Finit comes with its own tooling providing: `shutdown`, `reboot`, `poweroff`, and `suspend`, but also the traditional `init` and `telinit`, as well as a more modern `initctl` tool, detailed in the next section. For compatibility reasons Finit listens to the same set of signals as BusyBox init. This is not 100% compatible with SysV init, but clearly the more common combination for Finit. For more details, see [docs/signals.md](docs/signals.md). Finit also listens to the classic SysV init FIFO, used by `telinit`. Support for this is implemented by the `initctl.so` plugin. Hence, `telinit q` will work as the UNIX beards intended. ```shell ~ # telinit -h Usage: telinit [OPTIONS] [q | Q | 0-9] Options: -h, --help This help text -V, --version Show Finit version Commands: 0 Power-off the system, same as initctl poweroff 6 Reboot the system, same as initctl reboot 2, 3, 4, 5 Change runlevel. Starts services in new runlevel, stops any services in prev. runlevel that are not allowed in new. q, Q Reload *.conf in /etc/finit.d/, same as initctl reload or sending SIGHUP to PID 1 1, s, S Enter system rescue mode, runlevel 1 ``` Commands & Status ----------------- Finit also implements a more modern API to query status, and start/stop services, called `initctl`. Unlike `telinit` the `initctl` tool does not return until the given command has fully completed. ```shell ~ $ initctl -h Usage: initctl [OPTIONS] [COMMAND] Options: -v, --verbose Verbose output -h, --help This help text Commands: debug Toggle Finit (daemon) debug help This help text version Show Finit version list List all .conf in /etc/finit.d/ enable Enable .conf in /etc/finit.d/available/ disable Disable .conf in /etc/finit.d/[enabled/] touch Mark .conf in /etc/finit.d/ for reload reload Reload *.conf in /etc/finit.d/ (activates changes) cond set Set (assert) condition => +COND cond clear Clear (deassert) condition => -COND cond show Show condition status cond dump Dump all conditions and their status log [NAME] Show ten last Finit, or NAME, messages from syslog start [:ID] Start service by job# or name, with optional ID stop [:ID] Stop/Pause a running service by job# or name restart [:ID] Restart (stop/start) service by job# or name status [:ID] Show service status, by job# or name status | show Show status of services, default command runlevel [0-9] Show or set runlevel: 0 halt, 6 reboot reboot Reboot system halt Halt system poweroff Halt and power off system utmp show Raw dump of UTMP/WTMP db ``` For services *not* supporting `SIGHUP` the `` notation in the .conf file must be used to tell Finit to stop and start it on `reload` and `runlevel` changes. If `<>` holds more [conditions](docs/conditions.md), these will also affect how a service is maintained. **Note:** even though it is possible to start services not belonging in the current runlevel these services will not be respawned automatically by Finit if they exit (crash). Hence, if the runlevel is 2, the below Dropbear SSH service will not be restarted if it is killed or exits. ```shell ~ $ initctl status -v 1 running 476 [S12345] /sbin/watchdog -T 16 -t 2 -F /dev/watchdog 2 running 477 [S12345] /sbin/syslogd -n -b 3 -D 3 running 478 [S12345] /sbin/klogd -n 4:1 inetd 0 [2345] internal time allow *:37,!eth0 4:2 inetd 0 [2345] internal time allow eth0:3737 5:1 inetd 0 [2345] /sbin/telnetd allow *:23 deny eth0,eth1 5:2 inetd 0 [2345] /sbin/telnetd allow eth0:2323,eth2:2323,eth1:2323 6:1 inetd 0 [345] /sbin/dropbear allow eth0:222 6:2 inetd 0 [345] /sbin/dropbear allow *:22 deny eth0 ``` Requirements ------------ Finit is capable of running on both desktop/server systems with udev and embedded systems that usually come with BusyBox mdev. Some systems have systemd-udev or eudev today instead of the original udev, Finit probes for all of them at runtime and expects `/dev/` to be a writable file system using `devtmpfs`. It is also possible to run on a statically set up `/dev` if needed. It is however not a good idea to have both udev and mdev installed at the same time, this will lead to unpredictable results. At boot Finit calls either `mdev` or `udevd` to populate `/dev`, this is done slightly differently and on systems with udev you might want to add the following one-shot task early in your `/etc/finit.conf`: ```conf run [S] /sbin/udevadm settle --timeout=120 -- Waiting for udev ``` Finit has a built-in Getty for TTYs, but requires a working `/bin/login` or `/bin/sh`, if no TTYs are configured in `/etc/finit.conf`. For a fully operational system `/var`, `/run` and `/tmp` must be set up properly in `/etc/fstab` -- which is iterated over at boot. The built-in Inetd requires `/etc/services` and `/etc/protocols` to work with port names rather than numbers. Origin & References ------------------- This project is based on the [original finit][] by [Claudio Matsuoka][] which was reverse engineered from syscalls of the [EeePC fastinit][] — "gaps filled with frog DNA …" Finit is developed and maintained by [Joachim Nilsson][] at [GitHub][]. Please file bug reports, clone it, or send pull requests for bug fixes and proposed extensions. [1]: https://en.wikipedia.org/wiki/Process_supervision [2]: http://cr.yp.to/daemontools.html [3]: http://smarden.org/runit/ [4]: http://en.wikipedia.org/wiki/Init [5]: http://en.wikipedia.org/wiki/Runlevel [6]: https://www.freedesktop.org/wiki/Software/systemd/ [9]: https://github.com/troglobit/troglos [RFC862]: https://tools.ietf.org/html/rfc862 [RFC863]: https://tools.ietf.org/html/rfc863 [RFC864]: https://tools.ietf.org/html/rfc864 [RFC867]: https://tools.ietf.org/html/rfc867 [RFC868]: https://tools.ietf.org/html/rfc868 [init]: http://en.wikipedia.org/wiki/Init [upstart]: http://upstart.ubuntu.com/ [systemd]: http://www.freedesktop.org/wiki/Software/systemd/ [openrc]: http://www.gentoo.org/proj/en/base/openrc/ [run-parts(8)]: http://manpages.debian.org/cgi-bin/man.cgi?query=run-parts [original finit]: http://helllabs.org/finit/ [EeePC fastinit]: http://wiki.eeeuser.com/boot_process:the_boot_process [Claudio Matsuoka]: https://github.com/cmatsuoka [Joachim Nilsson]: http://troglobit.com [GitHub]: https://github.com/troglobit/finit [License]: https://en.wikipedia.org/wiki/MIT_License [License Badge]: https://img.shields.io/badge/License-MIT-yellow.svg [Travis]: https://travis-ci.org/troglobit/finit [Travis Status]: https://travis-ci.org/troglobit/finit.png?branch=master [Coverity Scan]: https://scan.coverity.com/projects/3545 [Coverity Status]: https://scan.coverity.com/projects/3545/badge.svg