From 08883f795856de8dd7ea83540c0d8bff9e74a29e Mon Sep 17 00:00:00 2001 From: "Mark D. Studebaker" Date: Sun, 25 Feb 2001 00:45:28 +0000 Subject: [PATCH] add entry for dual lm87's requiring different configuration git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1035 7894878c-1315-0410-8ee3-d5d059ff63e0 --- doc/FAQ | 24 ++++++++++++++++++++---- 1 file changed, 20 insertions(+), 4 deletions(-) diff --git a/doc/FAQ b/doc/FAQ index dfbc306f..1a17561f 100644 --- a/doc/FAQ +++ b/doc/FAQ @@ -65,6 +65,7 @@ sensor reading results. Why? 4.17A Bad readings from the AS99127F! 4.17B Bad readings from the VIA 686A! 4.17C Bad readings from the MTP008! +4.18 How do I configure two chips (LM87) differently? 4.19 Dmesg says Upgrade BIOS! I don't want to! 4.20 Sensors says 'Can't access /proc file' 4.21 Sensors says 'No sensors found!' @@ -411,7 +412,7 @@ readings. 4.3 Why do I have two Vcore readings, I have only one processor! - The LM78 family has seven voltage sensors. The default way of + The LM78 has seven voltage sensors. The default way of connecting them is used in the configuration file. This includes a VCore2, even if you do not have one. You can easily edit the configuration file to give it another name, or (in upcoming versions) to make this reading @@ -612,6 +613,19 @@ If your sensor type does not match the default, you will have to change it. See doc/chips/mtp008 for details. +4.18 How do I configure two chips (LM87) differently? + + There is a SuperMicro board with two LM87's on it that are +not hooked up in the same way, so they need different defaults. +For example, both CPU temperatures go to one LM87. + + Make two different sections in /etc/sensors.conf as follows: + chip "lm87-i2c-*-2c" + put configuration for the chip at 0x2c here + chip "lm87-i2c-*-2d" + put configuration for the chip at 0x2d here + + 4.19 Dmesg says Upgrade BIOS! I don't want to! If the problem is a PCI device is not present in 'lspci', the solution @@ -687,13 +701,15 @@ prog/eeprom/decode-dimms.pl to get more information than you ever wanted. These are often 'shadows' of you EEPROMs on your SDRAM DIMMs at addresses 0x50 - 0x57. They aren't really there. If you try and do a 'i2cdump' on them you won't get anything. This is probably -caused by some timing problem on your motherboard or on the DIMMs.x +caused by some timing problem on your motherboard or on the DIMMs. We don't know the exact cause. 4.24 Sensors-detect doesn't work at all - It could be many things. What was the problem? See below. + It could be many things. What was the problem? See below + in questions 4.24 A-C. + 4.24A Sensors-detect says "Couldn't open /proc/bus/i2c?!?" @@ -854,7 +870,7 @@ can not be sure. --------------------------------------------------------------------------------------- --------------------------------------------------------------------------------------- -Rev 2.3 (MDS) General update, 20010219 +Rev 2.3 (MDS) General update, 20010224 Rev 2.2 (Frodo) Corrections for lm_sensors 2.4, 19990920 Rev 2.1 (Frodo) Corrections for lm_sensors 2.2, 19990112 Rev 2.0 (Frodo) Major revision for lm_sensors 2.1, 19981229