diff --git a/prog/eeprom/decode-dimms.pl b/prog/eeprom/decode-dimms.pl index eec25212..52495189 100755 --- a/prog/eeprom/decode-dimms.pl +++ b/prog/eeprom/decode-dimms.pl @@ -64,6 +64,7 @@ # use strict; +use Fcntl qw(:DEFAULT :seek); use vars qw($opt_html $opt_body $opt_bodyonly $opt_igncheck $use_sysfs @vendors); @vendors = ( @@ -332,28 +333,26 @@ sub printh ($) # print header w/ given text } } -sub readspd16 ($$) { # reads 16 bytes from SPD-EEPROM +sub readspd64 ($$) { # reads 64 bytes from SPD-EEPROM my ($offset, $dimm_i) = @_; + my @bytes; if ($use_sysfs) { # Kernel 2.6 with sysfs - open (HANDLE, "/sys/bus/i2c/drivers/eeprom/$dimm_i/eeprom") + sysopen(HANDLE, "/sys/bus/i2c/drivers/eeprom/$dimm_i/eeprom", O_RDONLY) or die "Cannot open /sys/bus/i2c/drivers/eeprom/$dimm_i/eeprom"; binmode HANDLE; - seek (HANDLE, $offset, 0); - read (HANDLE, my $eeprom, 16); + sysseek(HANDLE, $offset, SEEK_SET); + sysread(HANDLE, my $eeprom, 64); close HANDLE; - my @bytes = (); - for my $i ( 0 .. 15 ) { - $_ = ord substr($eeprom, $i, 1); - push(@bytes, $_); - } - return @bytes; + @bytes = unpack("C64", $eeprom); } else { # Kernel 2.4 with procfs - $offset = sprintf('%02x', $offset); - $_ = `cat /proc/sys/dev/sensors/$dimm_i/$offset`; - return split(" "); + for my $i (0 .. 3) { + my $hexoff = sprintf('%02x', $offset + $i * 16); + push @bytes, split(" ", `cat /proc/sys/dev/sensors/$dimm_i/$hexoff`); + } } + return @bytes; } for (@ARGV) { @@ -413,8 +412,11 @@ for my $i ( 0 .. $#dimm_list ) { # Decode first 16 bytes prints "The Following is Required Data and is Applicable to all DIMM Types"; - my @bytes = readspd16(0, $dimm_list[$i]); - for my $j ( 0 .. 15 ) { $dimm_checksum = $dimm_checksum + $bytes[$j]; } + my @bytes = readspd64(0, $dimm_list[$i]); + for my $j (0 .. 62) { + $dimm_checksum = $dimm_checksum + $bytes[$j]; + } + $dimm_checksum &= 0xff; printl "# of bytes written to SDRAM EEPROM",$bytes[0]; @@ -536,192 +538,183 @@ for my $i ( 0 .. $#dimm_list ) { prints "The Following Apply to SDRAM DIMMs ONLY"; # Decode next 16 bytes - @bytes = readspd16(16, $dimm_list[$i]); - for my $j ( 0 .. 15 ) { $dimm_checksum = $dimm_checksum + $bytes[$j]; } - $l = "Burst lengths supported"; $temp=""; - if (($bytes[0] & 1) > 0) { $temp .= "Burst Length = 1\n"; } - if (($bytes[0] & 2) > 0) { $temp .= "Burst Length = 2\n"; } - if (($bytes[0] & 4) > 0) { $temp .= "Burst Length = 4\n"; } - if (($bytes[0] & 8) > 0) { $temp .= "Burst Length = 8\n"; } - if (($bytes[0] & 16) > 0) { $temp .= "Undefined! (bit 4)\n"; } - if (($bytes[0] & 32) > 0) { $temp .= "Undefined! (bit 5)\n"; } - if (($bytes[0] & 64) > 0) { $temp .= "Undefined! (bit 6)\n"; } - if (($bytes[0] & 128) > 0) { $temp .= "Burst Length = Page\n"; } - if ($bytes[0] == 0) { $temp .= "(None Supported)\n";} + if (($bytes[16] & 1) > 0) { $temp .= "Burst Length = 1\n"; } + if (($bytes[16] & 2) > 0) { $temp .= "Burst Length = 2\n"; } + if (($bytes[16] & 4) > 0) { $temp .= "Burst Length = 4\n"; } + if (($bytes[16] & 8) > 0) { $temp .= "Burst Length = 8\n"; } + if (($bytes[16] & 16) > 0) { $temp .= "Undefined! (bit 4)\n"; } + if (($bytes[16] & 32) > 0) { $temp .= "Undefined! (bit 5)\n"; } + if (($bytes[16] & 64) > 0) { $temp .= "Undefined! (bit 6)\n"; } + if (($bytes[16] & 128) > 0) { $temp .= "Burst Length = Page\n"; } + if ($bytes[16] == 0) { $temp .= "(None Supported)\n";} printl $l, $temp; $l = "Number of Device Banks"; - if ($bytes[1] == 0) { printl $l, "Undefined/Reserved!"; } - else { printl $l, $bytes[1]; } + if ($bytes[17] == 0) { printl $l, "Undefined/Reserved!"; } + else { printl $l, $bytes[17]; } $l = "Supported CAS Latencies"; $temp=""; - if (($bytes[2] & 1) > 0) { $temp .= "CAS Latency = 1\n";} - if (($bytes[2] & 2) > 0) { $temp .= "CAS Latency = 2\n"; } - if (($bytes[2] & 4) > 0) { $temp .= "CAS Latency = 3\n"; } - if (($bytes[2] & 8) > 0) { $temp .= "CAS Latency = 4\n"; } - if (($bytes[2] & 16) > 0) { $temp .= "CAS Latency = 5\n"; } - if (($bytes[2] & 32) > 0) { $temp .= "CAS Latency = 6\n"; } - if (($bytes[2] & 64) > 0) { $temp .= "CAS Latency = 7\n"; } - if (($bytes[2] & 128) > 0) { $temp .= "Undefined (bit 7)\n"; } - if ($bytes[2] == 0) { $temp .= "(None Supported)\n";} + if (($bytes[18] & 1) > 0) { $temp .= "CAS Latency = 1\n";} + if (($bytes[18] & 2) > 0) { $temp .= "CAS Latency = 2\n"; } + if (($bytes[18] & 4) > 0) { $temp .= "CAS Latency = 3\n"; } + if (($bytes[18] & 8) > 0) { $temp .= "CAS Latency = 4\n"; } + if (($bytes[18] & 16) > 0) { $temp .= "CAS Latency = 5\n"; } + if (($bytes[18] & 32) > 0) { $temp .= "CAS Latency = 6\n"; } + if (($bytes[18] & 64) > 0) { $temp .= "CAS Latency = 7\n"; } + if (($bytes[18] & 128) > 0) { $temp .= "Undefined (bit 7)\n"; } + if ($bytes[18] == 0) { $temp .= "(None Supported)\n";} printl $l, $temp; $l = "Supported CS Latencies"; $temp=""; - if (($bytes[3] & 1) > 0) { $temp .= "CS Latency = 0\n";} - if (($bytes[3] & 2) > 0) { $temp .= "CS Latency = 1\n"; } - if (($bytes[3] & 4) > 0) { $temp .= "CS Latency = 2\n"; } - if (($bytes[3] & 8) > 0) { $temp .= "CS Latency = 3\n"; } - if (($bytes[3] & 16) > 0) { $temp .= "CS Latency = 4\n"; } - if (($bytes[3] & 32) > 0) { $temp .= "CS Latency = 5\n"; } - if (($bytes[3] & 64) > 0) { $temp .= "CS Latency = 6\n"; } - if (($bytes[3] & 128) > 0) { $temp .= "Undefined (bit 7)\n"; } - if ($bytes[3] == 0) { $temp .= "(None Supported)\n";} + if (($bytes[19] & 1) > 0) { $temp .= "CS Latency = 0\n";} + if (($bytes[19] & 2) > 0) { $temp .= "CS Latency = 1\n"; } + if (($bytes[19] & 4) > 0) { $temp .= "CS Latency = 2\n"; } + if (($bytes[19] & 8) > 0) { $temp .= "CS Latency = 3\n"; } + if (($bytes[19] & 16) > 0) { $temp .= "CS Latency = 4\n"; } + if (($bytes[19] & 32) > 0) { $temp .= "CS Latency = 5\n"; } + if (($bytes[19] & 64) > 0) { $temp .= "CS Latency = 6\n"; } + if (($bytes[19] & 128) > 0) { $temp .= "Undefined (bit 7)\n"; } + if ($bytes[19] == 0) { $temp .= "(None Supported)\n";} printl $l, $temp; $l = "Supported WE Latencies"; $temp=""; - if (($bytes[4] & 1) > 0) { $temp .= "WE Latency = 0\n";} - if (($bytes[4] & 2) > 0) { $temp .= "WE Latency = 1\n"; } - if (($bytes[4] & 4) > 0) { $temp .= "WE Latency = 2\n"; } - if (($bytes[4] & 8) > 0) { $temp .= "WE Latency = 3\n"; } - if (($bytes[4] & 16) > 0) { $temp .= "WE Latency = 4\n"; } - if (($bytes[4] & 32) > 0) { $temp .= "WE Latency = 5\n"; } - if (($bytes[4] & 64) > 0) { $temp .= "WE Latency = 6\n"; } - if (($bytes[4] & 128) > 0) { $temp .= "Undefined (bit 7)\n"; } - if ($bytes[4] == 0) { $temp .= "(None Supported)\n";} + if (($bytes[20] & 1) > 0) { $temp .= "WE Latency = 0\n";} + if (($bytes[20] & 2) > 0) { $temp .= "WE Latency = 1\n"; } + if (($bytes[20] & 4) > 0) { $temp .= "WE Latency = 2\n"; } + if (($bytes[20] & 8) > 0) { $temp .= "WE Latency = 3\n"; } + if (($bytes[20] & 16) > 0) { $temp .= "WE Latency = 4\n"; } + if (($bytes[20] & 32) > 0) { $temp .= "WE Latency = 5\n"; } + if (($bytes[20] & 64) > 0) { $temp .= "WE Latency = 6\n"; } + if (($bytes[20] & 128) > 0) { $temp .= "Undefined (bit 7)\n"; } + if ($bytes[20] == 0) { $temp .= "(None Supported)\n";} printl $l, $temp; $l = "SDRAM Module Attributes"; $temp=""; - if (($bytes[5] & 1) > 0) { $temp .= "Buffered Address/Control Inputs\n";} - if (($bytes[5] & 2) > 0) { $temp .= "Registered Address/Control Inputs\n"; } - if (($bytes[5] & 4) > 0) { $temp .= "On card PLL (clock)\n"; } - if (($bytes[5] & 8) > 0) { $temp .= "Buffered DQMB Inputs\n"; } - if (($bytes[5] & 16) > 0) { $temp .= "Registered DQMB Inputs\n"; } - if (($bytes[5] & 32) > 0) { $temp .= "Differential Clock Input\n"; } - if (($bytes[5] & 64) > 0) { $temp .= "Redundant Row Address\n"; } - if (($bytes[5] & 128) > 0) { $temp .= "Undefined (bit 7)\n"; } - if ($bytes[5] == 0) { $temp .= "(None Reported)\n";} + if (($bytes[21] & 1) > 0) { $temp .= "Buffered Address/Control Inputs\n";} + if (($bytes[21] & 2) > 0) { $temp .= "Registered Address/Control Inputs\n"; } + if (($bytes[21] & 4) > 0) { $temp .= "On card PLL (clock)\n"; } + if (($bytes[21] & 8) > 0) { $temp .= "Buffered DQMB Inputs\n"; } + if (($bytes[21] & 16) > 0) { $temp .= "Registered DQMB Inputs\n"; } + if (($bytes[21] & 32) > 0) { $temp .= "Differential Clock Input\n"; } + if (($bytes[21] & 64) > 0) { $temp .= "Redundant Row Address\n"; } + if (($bytes[21] & 128) > 0) { $temp .= "Undefined (bit 7)\n"; } + if ($bytes[21] == 0) { $temp .= "(None Reported)\n";} printl $l, $temp; $l = "SDRAM Device Attributes (General)"; $temp=""; - if (($bytes[6] & 1) > 0) { $temp .= "Supports Early RAS# Recharge\n";} - if (($bytes[6] & 2) > 0) { $temp .= "Supports Auto-Precharge\n"; } - if (($bytes[6] & 4) > 0) { $temp .= "Supports Precharge All\n"; } - if (($bytes[6] & 8) > 0) { $temp .= "Supports Write1/Read Burst\n"; } - if (($bytes[6] & 16) > 0) { $temp .= "Lower VCC Tolerance:5%\n"; } - if (($bytes[6] & 16) == 0) { $temp .= "Lower VCC Tolerance:10%\n"; } - if (($bytes[6] & 32) > 0) { $temp .= "Upper VCC Tolerance:5%\n"; } - if (($bytes[6] & 32) == 0) { $temp .= "Upper VCC Tolerance:10%\n"; } - if (($bytes[6] & 64) > 0) { $temp .= "Undefined (bit 6)\n"; } - if (($bytes[6] & 128) > 0) { $temp .= "Undefined (bit 7)\n"; } + if (($bytes[22] & 1) > 0) { $temp .= "Supports Early RAS# Recharge\n";} + if (($bytes[22] & 2) > 0) { $temp .= "Supports Auto-Precharge\n"; } + if (($bytes[22] & 4) > 0) { $temp .= "Supports Precharge All\n"; } + if (($bytes[22] & 8) > 0) { $temp .= "Supports Write1/Read Burst\n"; } + if (($bytes[22] & 16) > 0) { $temp .= "Lower VCC Tolerance: 5%\n"; } + if (($bytes[22] & 16) == 0) { $temp .= "Lower VCC Tolerance: 10%\n"; } + if (($bytes[22] & 32) > 0) { $temp .= "Upper VCC Tolerance: 5%\n"; } + if (($bytes[22] & 32) == 0) { $temp .= "Upper VCC Tolerance: 10%\n"; } + if (($bytes[22] & 64) > 0) { $temp .= "Undefined (bit 6)\n"; } + if (($bytes[22] & 128) > 0) { $temp .= "Undefined (bit 7)\n"; } printl $l, $temp; $l = "SDRAM Cycle Time (2nd highest CAS)"; - $temp = $bytes[7] >> 4; + $temp = $bytes[23] >> 4; if ($temp == 0) { printl $l, "Undefined!"; } else { if ($temp < 4 ) {$temp=$temp + 15;} - printl $l, $temp + (($bytes[7] & 0xf) * 0.1) . "nS"; + printl $l, $temp + (($bytes[23] & 0xf) * 0.1) . "nS"; } $l = "SDRAM Access from Clock Time (2nd highest CAS)"; - $temp = $bytes[8] >> 4; + $temp = $bytes[24] >> 4; if ($temp == 0) { printl $l, "Undefined!"; } else { if ($temp < 4 ) {$temp=$temp + 15;} - printl $l, $temp + (($bytes[8] & 0xf) * 0.1) . "nS"; + printl $l, $temp + (($bytes[24] & 0xf) * 0.1) . "nS"; } prints "The Following are Optional (may be Bogus)"; $l = "SDRAM Cycle Time (3rd highest CAS)"; - $temp = $bytes[9] >> 2; + $temp = $bytes[25] >> 2; if ($temp == 0) { printl $l, "Undefined!"; } - else { printl $l, $temp + ($bytes[9] & 0x3) * 0.25 . "nS"; } + else { printl $l, $temp + ($bytes[25] & 0x3) * 0.25 . "nS"; } $l = "SDRAM Access from Clock Time (3rd highest CAS)"; - $temp = $bytes[10] >> 2; + $temp = $bytes[26] >> 2; if ($temp == 0) { printl $l, "Undefined!"; } - else { printl $l, $temp + ($bytes[10] & 0x3) * 0.25 . "nS"; } + else { printl $l, $temp + ($bytes[26] & 0x3) * 0.25 . "nS"; } prints "The Following are Required (for SDRAMs)"; $l = "Minimum Row Precharge Time"; - if ($bytes[11] == 0) { printl $l, "Undefined!"; } - else { printl $l, "$bytes[11]nS"; } + if ($bytes[27] == 0) { printl $l, "Undefined!"; } + else { printl $l, "$bytes[27]nS"; } $l = "Row Active to Row Active Min"; - if ($bytes[12] == 0) { printl $l, "Undefined!"; } - else { printl $l, "$bytes[12]nS"; } + if ($bytes[28] == 0) { printl $l, "Undefined!"; } + else { printl $l, "$bytes[28]nS"; } $l = "RAS to CAS Delay"; - if ($bytes[13] == 0) { printl $l, "Undefined!"; } - else { printl $l, "$bytes[13]nS"; } + if ($bytes[29] == 0) { printl $l, "Undefined!"; } + else { printl $l, "$bytes[29]nS"; } $l = "Min RAS Pulse Width"; - if ($bytes[14] == 0) { printl $l, "Undefined!"; } - else { printl $l, "$bytes[14]nS"; } + if ($bytes[30] == 0) { printl $l, "Undefined!"; } + else { printl $l, "$bytes[30]nS"; } prints "The Following are Required and Apply to ALL DIMMs"; $l = "Row Densities"; $temp=""; - if (($bytes[15] & 1) > 0) { $temp .= "4 MByte\n";} - if (($bytes[15] & 2) > 0) { $temp .= "8 MByte\n"; } - if (($bytes[15] & 4) > 0) { $temp .= "16 MByte\n"; } - if (($bytes[15] & 8) > 0) { $temp .= "32 MByte\n"; } - if (($bytes[15] & 16) > 0) { $temp .= "64 MByte\n"; } - if (($bytes[15] & 32) > 0) { $temp .= "128 MByte\n"; } - if (($bytes[15] & 64) > 0) { $temp .= "256 MByte\n"; } - if (($bytes[15] & 128) > 0) { $temp .= "512 MByte\n"; } - if ($bytes[15] == 0) { $temp .= "(Undefined! -- None Reported!)\n";} + if (($bytes[31] & 1) > 0) { $temp .= "4 MByte\n";} + if (($bytes[31] & 2) > 0) { $temp .= "8 MByte\n"; } + if (($bytes[31] & 4) > 0) { $temp .= "16 MByte\n"; } + if (($bytes[31] & 8) > 0) { $temp .= "32 MByte\n"; } + if (($bytes[31] & 16) > 0) { $temp .= "64 MByte\n"; } + if (($bytes[31] & 32) > 0) { $temp .= "128 MByte\n"; } + if (($bytes[31] & 64) > 0) { $temp .= "256 MByte\n"; } + if (($bytes[31] & 128) > 0) { $temp .= "512 MByte\n"; } + if ($bytes[31] == 0) { $temp .= "(Undefined! -- None Reported!)\n";} printl $l, $temp; # Decode next 16 bytes (32-47) - @bytes = readspd16(32, $dimm_list[$i]); - for my $j ( 0 .. 15 ) { $dimm_checksum = $dimm_checksum + $bytes[$j]; } - prints "The Following are Proposed and Apply to SDRAM DIMMs"; $l = "Command and Address Signal Setup Time"; - $temp = (($bytes[0] & 0x7f) >> 4) + ($bytes[0] & 0xf) * 0.1; - printl $l, ( ($bytes[0] >> 7) ? -$temp : $temp ) . "nS"; + $temp = (($bytes[32] & 0x7f) >> 4) + ($bytes[32] & 0xf) * 0.1; + printl $l, ( ($bytes[32] >> 7) ? -$temp : $temp ) . "nS"; $l = "Command and Address Signal Hold Time"; - $temp = (($bytes[1] & 0x7f) >> 4) + ($bytes[1] & 0xf) * 0.1; - printl $l, ( ($bytes[1] >> 7) ? -$temp : $temp ) . "nS"; + $temp = (($bytes[33] & 0x7f) >> 4) + ($bytes[33] & 0xf) * 0.1; + printl $l, ( ($bytes[33] >> 7) ? -$temp : $temp ) . "nS"; $l = "Data Signal Setup Time"; - $temp =(($bytes[2] & 0x7f) >> 4) + ($bytes[2] & 0xf) * 0.1; - printl $l, ( ($bytes[2] >> 7) ? -$temp : $temp ) . "nS"; + $temp = (($bytes[34] & 0x7f) >> 4) + ($bytes[34] & 0xf) * 0.1; + printl $l, ( ($bytes[34] >> 7) ? -$temp : $temp ) . "nS"; $l = "Data Signal Hold Time"; - $temp = (($bytes[3] & 0x7f) >> 4) + ($bytes[3] & 0xf) * 0.1; - printl $l, ( ($bytes[3] >> 7) ? -$temp : $temp ) . "nS"; + $temp = (($bytes[35] & 0x7f) >> 4) + ($bytes[35] & 0xf) * 0.1; + printl $l, ( ($bytes[35] >> 7) ? -$temp : $temp ) . "nS"; # That's it for the lower part of an SDRAM EEPROM's memory! # Decode next 16 bytes (48-63) - @bytes = readspd16(48, $dimm_list[$i]); - for my $j ( 0 .. 14 ) { $dimm_checksum = $dimm_checksum + $bytes[$j]; } - - printl "SPD Revision code ", sprintf("%x", $bytes[14]); + printl "SPD Revision code ", sprintf("%x", $bytes[62]); $l = "EEPROM Checksum of bytes 0-62"; - $dimm_checksum &= 0xff; - printl $l, ($bytes[15]==$dimm_checksum? - sprintf("OK (0x%.2X)",$bytes[15]): - sprintf("Bad (found 0x%.2X, calculated 0x%.2X)\n",$bytes[15],$dimm_checksum)); + printl $l, ($bytes[63] == $dimm_checksum ? + sprintf("OK (0x%.2X)", $bytes[63]): + sprintf("Bad (found 0x%.2X, calculated 0x%.2X)\n", + $bytes[63], $dimm_checksum)); - if($bytes[15]==$dimm_checksum || $opt_igncheck) { -# Decode next 16 bytes (64-79) - @bytes = readspd16(64, $dimm_list[$i]); + if($bytes[63]==$dimm_checksum || $opt_igncheck) { +# Decode next 48 bytes (64-111) + @bytes = readspd64(64, $dimm_list[$i]); $l = "Manufacturer"; # $extra is a reference to an array containing up to @@ -738,46 +731,39 @@ for my $i ( 0 .. $#dimm_list ) { printl $l, $temp; $l = "Manufacurer's Part Number"; -# Decode next 16 bytes (80-95) - my @bytes2= readspd16(80, $dimm_list[$i]); - - $temp = pack("C18",$bytes[9],$bytes[10],$bytes[11],$bytes[12],$bytes[13],$bytes[14],$bytes[15], - $bytes2[0],$bytes2[1],$bytes2[2],$bytes2[3],$bytes2[4],$bytes2[5],$bytes2[6],$bytes2[7],$bytes2[8],$bytes2[9],$bytes2[10]); + $temp = pack("C18", @bytes[9..26]); printl $l, $temp; $l = "Revision Code"; - $temp = sprintf("0x%.2X%.2X\n",$bytes2[11],$bytes2[12]); + $temp = sprintf("0x%.2X%.2X\n", @bytes[27..28]); printl $l, $temp; $l = "Manufacturing Date"; - $temp = sprintf("0x%.2X%.2X\n",$bytes2[13],$bytes2[14]); + $temp = sprintf("0x%.2X%.2X\n", @bytes[29..30]); printl $l, $temp; $l = "Assembly Serial Number"; -# Decode next 16 bytes (96-111) - @bytes = readspd16(96, $dimm_list[$i]); - - $temp = sprintf("0x%.2X%.2X%.2X%.2X\n",$bytes2[15],$bytes[0],$bytes[1],$bytes[2]); + $temp = sprintf("0x%.2X%.2X%.2X%.2X\n", @bytes[31..34]); + printl $l, $temp; + # Decode next 16 bytes (112-127) - @bytes = readspd16(112, $dimm_list[$i]); - $l = "Intel Specification for Frequency"; - if ($bytes[14] == 102) { printl $l, "66MHz\n"; } - elsif ($bytes[14] == 100) { printl $l, "100MHz\n"; } + if ($bytes[62] == 102) { printl $l, "66MHz\n"; } + elsif ($bytes[62] == 100) { printl $l, "100MHz\n"; } else { printl $l, "Undefined!\n"; } $l = "Intel Spec Details for 100MHz Support"; $temp=""; - if (($bytes[15] & 1) > 0) { $temp .= "Intel Concurrent AutoPrecharge\n";} - if (($bytes[15] & 2) > 0) { $temp .= "CAS Latency = 2\n";} - if (($bytes[15] & 4) > 0) { $temp .= "CAS Latency = 3\n";} - if (($bytes[15] & 8) > 0) { $temp .= "Junction Temp A (90 degrees C)\n";} - if (($bytes[15] & 8) == 0) { $temp .= "Junction Temp B (100 degrees C)\n";} - if (($bytes[15] & 16) > 0) { $temp .= "CLK 3 Connected\n";} - if (($bytes[15] & 32) > 0) { $temp .= "CLK 2 Connected\n";} - if (($bytes[15] & 64) > 0) { $temp .= "CLK 1 Connected\n";} - if (($bytes[15] & 128) > 0) { $temp .= "CLK 0 Connected\n";} - if ($bytes[15] > 175) { $temp .= "Double Sided DIMM\n"; } + if (($bytes[63] & 1) > 0) { $temp .= "Intel Concurrent AutoPrecharge\n";} + if (($bytes[63] & 2) > 0) { $temp .= "CAS Latency = 2\n";} + if (($bytes[63] & 4) > 0) { $temp .= "CAS Latency = 3\n";} + if (($bytes[63] & 8) > 0) { $temp .= "Junction Temp A (90 degrees C)\n";} + if (($bytes[63] & 8) == 0) { $temp .= "Junction Temp B (100 degrees C)\n";} + if (($bytes[63] & 16) > 0) { $temp .= "CLK 3 Connected\n";} + if (($bytes[63] & 32) > 0) { $temp .= "CLK 2 Connected\n";} + if (($bytes[63] & 64) > 0) { $temp .= "CLK 1 Connected\n";} + if (($bytes[63] & 128) > 0) { $temp .= "CLK 0 Connected\n";} + if ($bytes[63] > 175) { $temp .= "Double Sided DIMM\n"; } else { $temp .= "Single Sided DIMM\n";} printl $l, $temp; }