diff --git a/configs/Jetway/NC92-330-LF.conf b/configs/Jetway/NC92-330-LF.conf
new file mode 100644
index 00000000..d2087642
--- /dev/null
+++ b/configs/Jetway/NC92-330-LF.conf
@@ -0,0 +1,75 @@
+# Configuration contributed by Maciej Żenczykowski.
+# Kernel modules used: f71882fg, coretemp.
+
+
+# Jetway NC92-330-LF
+
+chip "f71862fg-*"
+
+    label in0 "Vcc3V"
+    label in1 "Vcore"
+    label in2 "   NB"
+    label in3 "+ 5V"
+    label in4 "+12V"
+    label in5 "5VSB"
+    label in6 "VDIMM"
+    label in7 "VSB3V"
+    label in8 "Vbat"
+
+    label fan1 "CPUFAN"
+    label fan2 "SYSFAN1"
+    label fan3 "SYSFAN2"
+
+    label temp1 "?CPU Temp"
+    label temp2 "?Sys Temp"
+    label temp3 "???? Temp"
+
+# According to datasheet, 3VCC/VSB/VBAT
+# (ie. Vcc3V/VSB3V/Vbat, or in0/in7/in8)
+# use internal R1=R2=150K Ohm resistors
+#
+# remember V_in_to_chip = V_real * R2 / (R1 + R2)
+# (where V_real----R1---*----V_in_to_chip) [max 2.048V]
+# (                     |                )
+# (                    R2                )
+# (                     |                )
+# (                    GND               )
+#
+# It would seem that VDIMM is the same...
+# Hence those four are set to use "@*2, @/2"
+#
+# The values of 5.25 for +5V and 5VSB and 11 for +12V
+# are from the datasheet as well (after juggling):
+#
+# VCORE    R1=1K   R2=inf VCORE  -> *1
+# VRAM     R1=10K  R2=10K VIN2   -> *2
+# VCHIPSET R1=4.7K R2=10K VIN3   -> *1.47
+# VCC5V    R1=20K  R2=4.7 VIN4   -> *5.255319148
+# +12V     R1=200K R2=20K VIN5   -> *11
+# VCC1.5V  R1=10K  R2=inf VIN6   -> *1
+
+    compute in0 @*2, @/2
+    compute in1 @, @
+    compute in2 @, @
+    compute in3 @*5.255319148, @/5.255319148
+    compute in4 @*11, @/11
+    compute in5 @*5.255319148, @/5.255319148
+    compute in6 @*2, @/2
+    compute in7 @*2, @/2
+    compute in8 @*2, @/2
+
+#   set temp1_type 2
+    set temp1_max        85
+    set temp1_max_hyst   81
+    set temp1_crit       65
+#   set temp1_crit_hyst  61
+#   set temp2_type 2
+    set temp2_max        85
+    set temp2_max_hyst   81
+    set temp2_crit      100
+#   set temp2_crit_hyst  96
+#   set temp3_type 2
+    set temp3_max        70
+    set temp3_max_hyst   68
+    set temp3_crit       85
+#   set temp3_crit_hyst  83
diff --git a/configs/Kontron/986LCD-M.conf b/configs/Kontron/986LCD-M.conf
new file mode 100644
index 00000000..cf36bd61
--- /dev/null
+++ b/configs/Kontron/986LCD-M.conf
@@ -0,0 +1,48 @@
+# Voltage section for the Kontron 986LCD-M:
+
+chip "w83627thf-*"
+
+# Voltages
+
+    label in0  "Vcore"
+    label in1  "+12V"
+    label in2  "+3.3V"
+    label in3  "+5V"
+    label in4  "+1.5V"
+    label in7  "5VSB"
+    label in8  "Vbat"
+
+    # External resistors
+    compute in1  @ * (1 + 10/3.57), @ / (1 + 10/3.57)
+    # Internal resistors
+    compute in3  @ * (1 + 34/51), @ / (1 + 34/51)
+    compute in7  @ * (1 + 34/51), @ / (1 + 34/51)
+
+    set in1_min  12.0 * 0.95
+    set in1_max  12.0 * 1.05
+    set in2_min   3.3 * 0.95
+    set in2_max   3.3 * 1.05
+    set in3_min   5.0 * 0.95
+    set in3_max   5.0 * 1.05
+    set in4_min   1.5 * 0.95
+    set in4_max   1.5 * 1.05
+    set in7_min   5.0 * 0.90
+    set in7_max   5.0 * 1.10
+    set in8_min   3.0 * 0.90
+    set in8_max   3.0 * 1.15
+
+# Fans
+
+    label fan1  "Sys Fan"
+    label fan2  "CPU Fan"
+    label fan3  "Aux Fan"
+
+# Temperatures
+
+   label temp1 "M/B Temp"
+   label temp2 "CPU Temp"
+   # temp3 is an optional external sensor
+
+   # Default limits for temp2 and temp3 are sane, but not for temp1
+   set temp1_max       80
+   set temp1_max_hyst  75
diff --git a/configs/MSI/945P-Neo2-F.conf b/configs/MSI/945P-Neo2-F.conf
new file mode 100644
index 00000000..1fa26d02
--- /dev/null
+++ b/configs/MSI/945P-Neo2-F.conf
@@ -0,0 +1,56 @@
+# Winbond W83627EHF configuration contributed by Dmitry Pechnikov
+# This is for an MSI 945P Neo2-F aka MS-7176.
+chip "w83627ehf-*" "w83627dhg-*"
+
+    label in0 "VCore"
+    label in1 "+12V"
+    label in2 "AVCC"
+    label in3 "3VCC"
+    label in6 "+5V"
+    label in7 "VSB"
+    label in8 "VBAT"
+
+# +12V is in1 and +5V is in6 as recommended by datasheet
+    compute in1 @*(1+(56/10)),  @/(1+(56/10))
+    compute in6 @*(1+(22/10)),  @/(1+(22/10))
+     
+    set in1_min   12.0*0.9
+    set in1_max   12.0*1.1
+    set in6_min   5.0*0.9
+    set in6_max   5.0*1.1
+
+    set in2_min   3.3*0.9
+    set in2_max   3.3*1.1
+    set in3_min   3.3*0.9
+    set in3_max   3.3*1.1
+    set in7_min   3.3*0.9
+    set in7_max   3.3*1.1
+    set in8_min   3.3*0.9
+    set in8_max   3.3*1.1
+
+    ignore in4
+    ignore in5
+    ignore in9
+
+# Fans
+    label fan1      "Case Fan"
+    label fan2      "CPU Fan"
+    label fan3      "Aux Fan"
+   
+    ignore fan1
+    ignore fan3
+    ignore fan5
+#   set fan1_min    1200
+    set fan2_min    1000
+
+# Temperatures
+    label temp1     "Sys Temp"
+    label temp2     "CPU Temp"
+    label temp3     "AUX Temp"
+
+    set temp1_max       55
+    set temp1_max_hyst  48
+    set temp2_max       55
+    set temp2_max_hyst  47
+    set temp3_max       55
+    set temp3_max_hyst  50
diff --git a/configs/MSI/975X-Platinum.conf b/configs/MSI/975X-Platinum.conf
new file mode 100644
index 00000000..09b97111
--- /dev/null
+++ b/configs/MSI/975X-Platinum.conf
@@ -0,0 +1,63 @@
+# Configuration file for the MSI 975X Platinum (MS-7246),
+# contributed by Leonardo Marín.
+
+
+chip "w83627ehf-*" "w83627dhg-*"
+
+ label in0 "VCore" # CPU Core Voltage
+ label in1 "VPCIEx" # PCI Express Voltage
+ label in2 "AVCC"
+ label in3 "3VCC"
+ label in6 "+ 5V" # +5V, or so i think
+ label in7 "3VSB"
+ label in8 "VBAT"
+ label in9 "+12V" # +12V, or so i think
+
+## +12V is in9 and +5V is in6 ##
+ compute in9 @*(1+(56/10)), @/(1+(56/10))
+ compute in6 @*(1+(22/10)), @/(1+(22/10))
+
+ set in9_min 12.0*0.9
+ set in9_max 12.0*1.1
+ set in6_min 5.0*0.9
+ set in6_max 5.0*1.1
+
+ set in0_min 0.9
+ set in0_max 1.7
+ set in1_min 1.4
+ set in1_max 2.0
+ set in2_min 3.3*0.9
+ set in2_max 3.3*1.1
+ set in3_min 3.3*0.9
+ set in3_max 3.3*1.1
+ set in7_min 3.3*0.9
+ set in7_max 3.3*1.1
+ set in8_min 3.0*0.9
+ set in8_max 3.3*1.1
+
+ ignore in4
+ ignore in5
+
+## Temperatures ##
+
+ label temp1 "Sys Temp"
+ label temp2 "CPU Temp"
+ label temp3 "Aux Temp"
+
+ set temp1_max 55
+ set temp1_max_hyst 48
+ set temp2_max 55
+ set temp2_max_hyst 47
+ set temp3_max 55
+ set temp3_max_hyst 50
+
+## Fans ##
+
+ label fan1 "PSU Fan"
+ label fan2 "CPU Fan"
+ label fan3 "NB Fan"
+ label fan4 "Sys Fan"
+
+ set fan2_min 800
+
+ ignore fan5
diff --git a/configs/MSI/GF615M-P33.conf b/configs/MSI/GF615M-P33.conf
new file mode 100644
index 00000000..7ee1aef5
--- /dev/null
+++ b/configs/MSI/GF615M-P33.conf
@@ -0,0 +1,60 @@
+# Contributed by John Smith.
+
+
+# lm_sensors configuration file for the MSI GF615M-P33 rev 1.3 (MS-7597)
+# 2011-07-14, Kid from Belgrade
+# tweaked from config for MSI P35 Neo / MSI MS-7360 motherboard
+# 2007-09-21, Andre Jagusch
+# Comments welcome!
+
+chip "f71889ed-*"
+
+# Temperature
+    label temp1       "CPU"
+    label temp2       "System"
+    ignore temp3
+
+# Fans
+    label fan1        "CPU"
+    label fan2        "System"
+    label fan3        "Misc"
+
+# sensors in2, in3, in6, in7 and in8  may be ignored since
+# they are not shown in BIOS for MS-7597
+# in6 is always 0.00
+# Voltage
+    label in0         "+3.3V"
+    label in1         "Vcore"
+#    ignore in2
+#    ignore in3
+    label in2         "Vdimm"
+    label in3         "Vchip"
+    label in4         "+5V"
+    label in5         "+12V"
+    ignore in6
+#    ignore in7
+#    ignore in8
+    label in7         "3VSB"
+    label in8         "Battery"
+
+# never change the in0, in7 and in8 compute, these are hardwired in the chip!
+# +5V, +12V and +3.3V computes looking fine for MS-7597, nothing changed
+    compute in0       (@ * 2), (@ / 2)
+    compute in2       (@ * 2), (@ / 2)
+    compute in3       (@ * 2), (@ / 2)
+    compute in4       (@ * 5.25), (@ / 5.25)
+    compute in5       (@ * 11), (@ / 11)
+    compute in6       (@ * 6.585), (@ / 6.585)
+    compute in7       (@ * 2), (@ / 2)
+    compute in8       (@ * 2), (@ / 2)
+
+
+# On Fintek, first sensor is below or near the CPU socket (how to determine this?)
+# CPU temperature is also measurable by on-die sensor on K10 series.
+# Now I have not found this anywhere and correction is correlated with Fintek,
+# tweaked for Athlon II x2 250, may differ for others.
+chip "k10temp-*"
+
+   label temp1 "CPU K10 Temp"
+
+   compute temp1 (@ + 5.5), (@ - 5.5)
diff --git a/configs/MSI/IM-945GC.conf b/configs/MSI/IM-945GC.conf
new file mode 100644
index 00000000..5bd7df18
--- /dev/null
+++ b/configs/MSI/IM-945GC.conf
@@ -0,0 +1,58 @@
+# Configuration file contributed by Bryan Guidroz.
+
+
+chip "f71882fg-isa-0a10"
+
+# Ignore - Voltage
+# The F71882FG uses an 8-bit, 8 mV LSB ADC for voltage monitoring.
+# This means that it can measure up to 2.04 V directly. This is the value
+# of in2, in3 and in6 on the MSI MS-9832, which means these inputs
+# are saturated. This means these inputs are unused.
+
+   ignore in2
+   ignore in3
+   ignore in6
+
+# Ignore - Fans
+# The MSI MS-9832 uses fan1 (CPU Fan) and fan2 (System Fan).
+# This means other fans are unused.
+
+   ignore fan3
+   ignore fan4
+
+# Ignore - Temps
+# The MSI MS-9832 uses temp1 (CPU temp) and temp3 (System temp).
+# This means temp2 is unused.
+
+   ignore temp2
+
+# Other - Voltages
+# in0 (+3.3v), in7 (3VSB), and in8 (Vbat) are internally monitored voltages
+# with internal dividers. This means the values are properly set and do not
+# need to be defined in this configuration as they should be reported properly.
+
+# Voltages
+   label in1 "Vcore"
+   label in4 "+5V"
+   label in5 "+12V"
+
+   compute in4  @*(1+200/47),  @/(1+200/47)
+   compute in5  @*(1+200/20),  @/(1+200/20)
+
+   set in1_max  1.1625 * 1.05
+
+# Fans
+   label fan1 "CPU Fan"
+   label fan2 "Sys Fan"
+
+   set fan1_min 2100
+   set fan2_min 1400
+
+# Temperatures
+   label temp1 "CPU Temp"
+   label temp3 "Sys Temp"
+
+   set temp1_max       60
+   set temp1_max_hyst  58
+   set temp3_max       50
+   set temp3_max_hyst  48
diff --git a/configs/MSI/IM-945GSE-A.conf b/configs/MSI/IM-945GSE-A.conf
new file mode 100644
index 00000000..51aac2d2
--- /dev/null
+++ b/configs/MSI/IM-945GSE-A.conf
@@ -0,0 +1,39 @@
+# lm_sensors configuration file for the MSI IM-945GSE-A motherboard
+# Atom N270, Dual Gigabit Intel 82574L controllers, VGA, DVI
+# 2009-07-01 Thomas Ettwein
+# 2010-08-29 Leo Krueger
+
+chip "f71882fg-*"
+
+# Temperature
+     label temp1       "CPU"
+     label temp2       "Systemboard"
+     ignore temp3
+
+# Fans
+      ignore fan1 # no connector on board
+      label fan2 "CPUFAN1"
+      ignore fan3 # no connector on board
+      ignore fan4 # no connector on board
+
+
+# Voltage
+     label in0         "3.3V"
+     label in1         "Vcore"
+     label in2         "Vdimm"
+     label in3         "Vchip"
+     label in4         "+5V"
+     label in5         "12V"
+     label in6         "5VSB"
+     label in7         "3VSB"
+     label in8         "Battery"
+
+# never change the in0, in7 and in8 compute, these are hardwired in the chip!
+     compute in0       (@ * 2), (@ / 2)
+     compute in2       (@ * 2), (@ / 2)
+     compute in3       (@ * 2), (@ / 2)
+     compute in4       (@ * 5.25), (@ / 5.25)
+     compute in5       (@ * 11.0), (@ / 11.0)
+     compute in6       (@ * 5.25), (@ / 5.25)
+     compute in7       (@ * 2), (@ / 2)
+     compute in8       (@ * 2), (@ / 2)
diff --git a/configs/MSI/P35-Neo.conf b/configs/MSI/P35-Neo.conf
new file mode 100644
index 00000000..72cb75a1
--- /dev/null
+++ b/configs/MSI/P35-Neo.conf
@@ -0,0 +1,37 @@
+# lm_sensors configuration file for the MSI P35 Neo / MSI MS-7360 motherboard
+# 2007-09-21, Andre Jagusch
+# Comments welcome!
+
+chip "f71882fg-*"
+
+# Temperature
+    label temp1       "CPU"
+    label temp2       "System"
+    ignore temp3
+
+# Fans
+    label fan1        "CPU"
+    label fan2        "System"
+    label fan3        "Power"
+    label fan4        "Aux"
+
+# Voltage
+    label in0         "3.3V"
+    label in1         "Vcore"
+    label in2         "Vdimm"
+    label in3         "Vchip"
+    label in4         "+5V"
+    label in5         "12V"
+    label in6         "5VSB"
+    label in7         "3VSB"
+    label in8         "Battery"
+
+# never change the in0, in7 and in8 compute, these are hardwired in the chip!
+    compute in0       (@ * 2), (@ / 2)
+    compute in2       (@ * 2), (@ / 2)
+    compute in3       (@ * 2), (@ / 2)
+    compute in4       (@ * 5.25), (@ / 5.25)
+    compute in5       (@ * 11), (@ / 11)
+    compute in6       (@ * 6.585), (@ / 6.585)
+    compute in7       (@ * 2), (@ / 2)
+    compute in8       (@ * 2), (@ / 2)
diff --git a/configs/MSI/P6N-SLI-FI.conf b/configs/MSI/P6N-SLI-FI.conf
new file mode 100644
index 00000000..73e22f04
--- /dev/null
+++ b/configs/MSI/P6N-SLI-FI.conf
@@ -0,0 +1,58 @@
+# Sasha Alexandr - grapefruitgirl at linuxmail dot org 
+# Sept 2007 - lm_sensors 2.10.4 
+# Platform: MS-7350-010  P6N-SLI-FI  mfg-date: 0707
+# Chipset: nVidia nforce2 650i/430i SLI
+# CPU: Intel CORE2 E2160 1.8 Ghz
+# BIOS: AMIBIOS v2.3
+#
+# Configuration for Fintek F71882FG Super-I/O device & coretemp driver for CORE2 CPU temps:
+
+  chip "f71882fg-isa-0a00"
+
+# NOTE: Fans 1 and 3 are switched around (somewhere).
+   label fan1 "CPU Cooler"
+   label fan2 "SysFan2: Rear Case"
+   label fan3 "SysFan1: some device"
+   label fan4 "SysFan3: some device"
+
+# NOTE: Set statements for fans & volts give an 'Unknown Feature' error currently. This should be fixed sometime.
+# The fans report exact same as BIOS; no computing needed.
+# Header labeled 'Sysfan3' on board doesn't seem to report RPM.
+
+   label temp1 "CPU Temp"
+   label temp2 "System Temp"
+   label temp3 "128 ignore"
+
+#  NOTE: temp1 reports 5'C less than BIOS so I add 5'C to it.
+   compute temp1 (@ + 5), (@ - 5)
+   ignore  temp3
+
+# Voltages:
+   label in0 "3.3V in0"
+   label in1 "CPU V-Core in1"
+   label in2 "+5V StBy in2"
+   label in3 "V-Dimm in3"
+   label in4 "+5V in4"
+   label in5 "+12V in5"
+   label in6 "0.888 ignore"
+   label in7 "3.3 V StBy in7"
+   label in8 "3V Battery in8"
+
+   compute in0  (@ * 2.00) ,(@ / 2.00)
+#  compute in1  (no computing necessary)
+   compute in2  (@ * 5.25) ,(@ / 5.25)
+   compute in3  (@ * 2.50) ,(@ / 2.50)
+#  NOTE: I add 0.005 to in4 so it reads EXACTLY as BIOS reads.
+   compute in4  (0.005 + @ * 5.25) ,(0.005 - @ / 5.25)
+   compute in5  (@ * 11.00),(@ / 11.00)
+   ignore  in6
+   compute in7  (@ * 2.00) ,(@ / 2.00)
+   compute in8  (@ * 2.00) ,(@ / 2.00)
+
+chip "coretemp-isa-0000"
+label temp1 "Core 0 Temp"
+
+chip "coretemp-isa-0001"
+label temp1 "Core 1 Temp"
+
+# EOF
diff --git a/configs/MSI/P965-Platinum.conf b/configs/MSI/P965-Platinum.conf
new file mode 100644
index 00000000..fd7b87dc
--- /dev/null
+++ b/configs/MSI/P965-Platinum.conf
@@ -0,0 +1,48 @@
+# Configuration file contributed by Olaf Mandel.
+
+
+# configuration for the Fintek f71882fg as used on the MSI X58 Pro-E (MS-7522)
+chip "f71882fg-*"
+
+# Temperature
+    label   temp1 "CPU"
+    label   temp2 "IOH"
+    label   temp3 "System"
+
+# Fans
+    label   fan1  "CPU"
+    label   fan2  "System 1" # This is not confirmed
+    label   fan3  "System 2"
+    ignore  fan2
+    ignore  fan4
+
+# Voltage
+    label   in0   "3.3V"
+    label   in1   "Vcore"
+    ignore  in2
+    ignore  in3
+    label   in4   "5V"
+    label   in5   "12V"
+    ignore  in6
+    label   in7   "3VSB"
+    label   in8   "Vbat"
+    compute in0   (@ * 2), (@ / 2) # Hardwired in chip, don't change
+    compute in4   (@ * 5.25), (@ / 5.25) # E24: (12 + 51) / 12
+    compute in5   (@ * 11), (@ / 11)     # E6:  ( 1 + 10) /  1
+    compute in7   (@ * 2), (@ / 2) # Hardwired in chip, don't change
+    compute in8   (@ * 2), (@ / 2) # Hardwired in chip, don't change
+
+# Thresholds
+    set in1_max           1.3
+    set temp1_max        85
+    set temp1_max_hyst   82
+    set temp1_crit      100
+    set temp1_crit_hyst  97
+    set temp2_max        75
+    set temp2_max_hyst   72
+    set temp2_crit       85
+    set temp2_crit_hyst  82
+    set temp3_max        55
+    set temp3_max_hyst   52
+    set temp3_crit       65
+    set temp3_crit_hyst  62
diff --git a/configs/MSI/X58-Pro-E.conf b/configs/MSI/X58-Pro-E.conf
new file mode 100644
index 00000000..fd7b87dc
--- /dev/null
+++ b/configs/MSI/X58-Pro-E.conf
@@ -0,0 +1,48 @@
+# Configuration file contributed by Olaf Mandel.
+
+
+# configuration for the Fintek f71882fg as used on the MSI X58 Pro-E (MS-7522)
+chip "f71882fg-*"
+
+# Temperature
+    label   temp1 "CPU"
+    label   temp2 "IOH"
+    label   temp3 "System"
+
+# Fans
+    label   fan1  "CPU"
+    label   fan2  "System 1" # This is not confirmed
+    label   fan3  "System 2"
+    ignore  fan2
+    ignore  fan4
+
+# Voltage
+    label   in0   "3.3V"
+    label   in1   "Vcore"
+    ignore  in2
+    ignore  in3
+    label   in4   "5V"
+    label   in5   "12V"
+    ignore  in6
+    label   in7   "3VSB"
+    label   in8   "Vbat"
+    compute in0   (@ * 2), (@ / 2) # Hardwired in chip, don't change
+    compute in4   (@ * 5.25), (@ / 5.25) # E24: (12 + 51) / 12
+    compute in5   (@ * 11), (@ / 11)     # E6:  ( 1 + 10) /  1
+    compute in7   (@ * 2), (@ / 2) # Hardwired in chip, don't change
+    compute in8   (@ * 2), (@ / 2) # Hardwired in chip, don't change
+
+# Thresholds
+    set in1_max           1.3
+    set temp1_max        85
+    set temp1_max_hyst   82
+    set temp1_crit      100
+    set temp1_crit_hyst  97
+    set temp2_max        75
+    set temp2_max_hyst   72
+    set temp2_crit       85
+    set temp2_crit_hyst  82
+    set temp3_max        55
+    set temp3_max_hyst   52
+    set temp3_crit       65
+    set temp3_crit_hyst  62
diff --git a/configs/PCchips/M811.conf b/configs/PCchips/M811.conf
new file mode 100644
index 00000000..18346bb4
--- /dev/null
+++ b/configs/PCchips/M811.conf
@@ -0,0 +1,97 @@
+# lm_sensors configuration file for the PCchips M811 motherboard
+
+# 2006-05-30, Hans de Goede <j.w.r.degoede@hhs.nl>
+
+# Comments welcome!
+
+
+
+chip "it87-*"
+
+
+
+# Voltage monitors as advised in the It8705 data sheet
+
+
+
+    label in0 "VCore"
+
+    label in1 "+2.5V"
+
+    label in2 "+3.3V"
+
+    label in8 "VBat" 
+
+    # 5, 12, -5, -12 and standby do not seem to be connected
+
+    ignore in3
+
+    ignore in4
+
+    ignore in5
+
+    ignore in6
+
+    ignore in7
+
+    # The It8705 doesn't monitor vid
+
+    ignore vid
+
+
+
+    # in0 will depend on your processor VID value, set to voltage specified in
+
+    # bios
+
+    set in0_min 1.4 * 0.95
+
+    set in0_max 1.4 * 1.05
+
+    set in1_min 2.4
+
+    set in1_max 2.6
+
+    set in2_min 3.3 * 0.95
+
+    set in2_max 3.3 * 1.05
+
+    #the chip does not support in8 min/max
+
+
+
+# Temperature
+
+
+
+    label temp2       "CPU Temp"
+
+    set   temp2_over  50
+
+    set   temp2_low   15
+
+    label temp3       "PWM Temp?"
+
+    set   temp3_over  65
+
+    set   temp3_low   15
+
+    # temp1 does not seem to be connected
+
+    ignore temp1
+
+
+
+# Fans
+
+    label fan1        "CPU fan"
+
+    label fan2        "SYS fan"
+
+    set fan1_min      3000
+
+    # The system fan is not always connected
+
+    set fan2_min      0
+
+    ignore fan3
diff --git a/configs/Sapphire/PureFusionMiniE350.conf b/configs/Sapphire/PureFusionMiniE350.conf
new file mode 100644
index 00000000..cbcc70ec
--- /dev/null
+++ b/configs/Sapphire/PureFusionMiniE350.conf
@@ -0,0 +1,31 @@
+# Contributed by tux99.
+
+
+chip "f71808e-*"
+
+   label  in0  "VCC  +3.3V"
+   # E-350 Vcore range is ~ 0.5V-1.35V (lowest idle state to max load)
+   label  in1  "CPU  Vcore"
+   ignore in2
+   label  in3  "DDR3 VDIMM"
+   label  in4  "FCH  +1.1V"
+   label  in5  "PCIe +1.8V"
+   label  in7  "3VSB +3.3V"
+   label  in8  "VBAT +3.0V"
+
+   compute in0  @*2, @/2
+   compute in3 (@ * 1.465), (@ / 1.465)
+   compute in7  @*2, @/2
+   compute in8  @*2, @/2
+
+   label fan1 "CPU Fan"
+   label fan2 "SYS Fan"
+
+   ignore fan3
+
+   label  temp1 "SYS Temp1"
+   label  temp2 "SYS Temp2"
+
+chip "k10temp-*"
+
+  label temp1 "CPU Temp"
diff --git a/configs/Shuttle/XPC-SG33G5M-Deluxe.conf b/configs/Shuttle/XPC-SG33G5M-Deluxe.conf
new file mode 100644
index 00000000..ff354d3c
--- /dev/null
+++ b/configs/Shuttle/XPC-SG33G5M-Deluxe.conf
@@ -0,0 +1,57 @@
+# lm_sensors 3 configuration file for the "Shuttle XPC SG33G5M Deluxe"
+# 2008-09-26, Matthieu Crapet <mcrapet@gmail.com>
+# Comments welcome!
+
+
+##
+# Chip 'ITE IT8718F Super IO Sensors' (it87.ko)
+##
+chip "it8718-*"
+
+#
+# Voltages (cpu0_vid, in0, ..., in8)
+#
+set in2_min  3.3 * 0.95
+set in2_max  3.3 * 1.05
+set in3_min    5 * 0.95
+set in3_max    5 * 1.05
+set in4_min   12 * 0.95
+set in4_max   12 * 1.05
+set in7_min    5 * 0.95
+set in7_max    5 * 1.05
+
+label in0 "CPU voltage"
+label in1 "Chipset voltage"
+label in2 "+3.3V"
+label in3 "+5V"
+label in4 "+12V"
+label in6 "DDR2 voltage"
+label in7 "+5VSB"
+label in8 "Battery voltage"
+
+ignore in5
+compute in3  ((6.8/10)+1)*@ , @/((6.8/10)+1)
+compute in4  ((30/10)+1)*@  , @/((30/10)+1)
+compute in7  ((6.8/10)+1)*@ , @/((6.8/10)+1)
+
+#
+# Fans (fan1, fan2, fan3)
+#
+set fan1_min 700
+label fan1  "System Fan"
+
+ignore fan2
+ignore fan3
+
+#
+# Temperature (temp1, temp2, temp3)
+#
+set   temp1_max 60
+set   temp1_min 15
+label temp1  "CPU Temp"
+
+set   temp2_max 65
+set   temp2_min 15
+label temp2  "M/B Temp"
+
+ignore temp3
diff --git a/configs/SuperMicro/C2SBE.conf b/configs/SuperMicro/C2SBE.conf
new file mode 100644
index 00000000..fa609d15
--- /dev/null
+++ b/configs/SuperMicro/C2SBE.conf
@@ -0,0 +1,92 @@
+# Example configuration for the SuperMicro C2SBE.
+# Contributed by Romain Dolbeau.
+
+# The C2SBA is similar to the C2SBE (only with video on-board).
+
+
+# settings for the supermicro C2SBE
+# Originally written by Romain Dolbeau <romain@dolbeau.org>
+# Uses at your own risk !
+#
+# Here's the info as supplied by Supermicro:
+#
+# Bus Type = ISAIO
+# One W83627DHG
+#
+# Windbond W83627DHG, IndexReg=295, DataReg=296
+# =============================================================
+# Fan1/CPU Fan Speed, Bank 0, Offset 0x29		RPM = 1350000/8/Data
+# Fan2 Fan Speed, Bank 5, Offset 0x53		RPM = 1350000/8/Data
+# Fan3 Fan Speed, Bank 0, Offset 0x28		RPM = 1350000/8/Data
+# Fan4 Fan Speed, Bank 0, Offset 0x3f		RPM = 1350000/8/Data
+# Fan5 Fan Speed, Bank 0, Offset 0x2a		RPM = 1350000/8/Data
+# CPU Voltage, Bank 0, Offset 0x20		Voltage = Data* 0.008
+# -12V Voltage, Bank 0, Offset 0x26		Voltage =((Data*0.008-2.048)/(10./242.))+2.048
+# +12V Voltage, Bank 0, Offset 0x21		Voltage = Data* 0.008/(10./160.)
+# +3.3V Voltage, Bank 0, Offset 0x22		Voltage = Data* 0.016
+# DIMM Voltage, Bank 0, Offset 0x24		Voltage = Data* 0.008
+# +5V Voltage, Bank 0, Offset 0x25		Voltage = Data* 0.008/(10./40.)
+# +3.3VSb Voltage, Bank 5, Offset 0x50		Voltage = Data* 0.016
+# Battery Voltage, Bank 5, Offset 0x51		Voltage = Data* 0.016
+# CPU Temperature, Bank 1, Offset 0x50		Temperature = Data
+# System Temperature, Bank 0, Offset 0x27		Temperature = Data
+# Chassis Intrusion, Bank 0, Offset 0x42, BitMask 0x10	1 = Bad, 0 = Good
+#			(Clear Bit: Bank 0, Offset 0x46, BitMask 0x80)
+
+chip "w83627dhg-*"
+# Voltages ; note that in the table above, the .008 and .016 factors are
+# already computed in the driver...
+    label in0 "VCore"
+    label in1 "+12V"
+    label in2 "+3.3V"
+    ignore in3
+    label in4 "DIMM Voltage"
+    label in5 "+5V"
+    label in6 "-12V"
+    label in7 "+3.3VSB"
+    label in8 "VBAT"
+
+# CPU Voltage limits are probably CPU-dependant
+    compute in0 @, @
+    set in0_min 1.0
+    set in0_max 1.4
+    compute in1 @*16,  @/16
+    set in1_min 12*0.95
+    set in1_max 12*1.05
+    compute in2 @, @
+    set in2_min 3.3*0.95
+    set in2_max 3.3*1.05
+#   compute in3 @, @
+# DIMM Voltage limits ???
+    compute in4 @, @
+    set in4_min 1.8*0.95
+    set in4_max 1.8*1.05
+    compute in5 @*4, @/4
+    set in5_min 5*0.95
+    set in5_max 5*1.05
+    compute in6 ((@-2.048)*24.2)+2.048, ((@-2.048)/24.2)+2.048
+    set in6_min -12*1.05
+    set in6_max -12*0.95
+    compute in7 @, @
+    set in7_min 3.3*0.95
+    set in7_max 3.3*1.05
+# VBAT Voltage limits ???
+    compute in8 @, @
+    set in8_min 3*0.9
+    set in8_max 3*1.1
+
+# Fans ; default in the driver is fine
+# you should ignore the unplugged ones
+   label fan1      "Fan 3"
+   label fan2      "Fan1/CPU Fan"
+   label fan3      "Fan 5"
+   label fan4      "Fan 4"
+   label fan5      "Fan 2"
+
+# Temperatures
+# Min and Max are environment-dependant
+   label temp1     "System Temp"
+   set temp1_max 45
+   label temp2     "CPU Temp"
+   set temp2_max 65
+   ignore temp3
diff --git a/configs/SuperMicro/C7H61.conf b/configs/SuperMicro/C7H61.conf
new file mode 100644
index 00000000..fc9eee4b
--- /dev/null
+++ b/configs/SuperMicro/C7H61.conf
@@ -0,0 +1,73 @@
+#
+# Libsensors configuration for SuperMicro C7H61-O and C7H61-L boards.
+# 
+# C7H61-L has a single nct6776 sensor chip.
+# C7H61-O has two sensor chips, nct6776 and nct6106. nct6106 is not used
+# for temperature, fans or voltage sensing. Hardware monitoring for this
+# chip is not enabled, and you should not enable it.
+# BIOS allows one to set nct6776 parameters, such as voltage or PWM fan
+# control and default strategy.
+#
+
+chip "nct6776-isa-0a30"
+
+    label in0 "Vcore"
+    label in1 "+12V"
+    label in2 "AVCC"
+    label in3 "+3.3V"
+    label in4 "VDIMM"
+    label in5 "+5V"
+    label in6 "VTT_CPU"
+    label in7 "3VSB"
+    label in8 "Vbat"
+
+    compute in1   @*6.6, @/6.6
+    compute in5   @*4, @/4
+
+    # min/max values are set by the BIOS
+
+    ignore fan1
+    label fan2 "System FAN4"
+    label fan3 "CPU Fan"
+    label fan4 "System FAN2"
+    label fan5 "System FAN3"
+
+    ignore temp7
+    ignore temp8
+    ignore temp9
+    ignore temp10
+
+    ignore intrusion1
+
+
+chip "nct6106-*"
+
+    ignore in0
+    ignore in1
+    label in2 "AVCC"
+    label in3 "+3.3V"
+    ignore in4
+    ignore in5
+    ignore in6
+    label in7 "Vbat"
+    ignore in8
+
+    set in2_min  3.3 * 0.90
+    set in2_max  3.3 * 1.10
+    set in3_min  3.3 * 0.90
+    set in3_max  3.3 * 1.10
+    set in7_min  3.3 * 0.90
+    set in7_max  3.3 * 1.10
+
+    ignore fan1
+    ignore fan2
+    ignore fan3
+
+    ignore temp1
+    ignore temp2
+    ignore temp3
+    ignore temp7
+    ignore temp8
+    ignore temp9
+
+    ignore intrusion0
diff --git a/configs/SuperMicro/C7X58.conf b/configs/SuperMicro/C7X58.conf
new file mode 100644
index 00000000..029ce152
--- /dev/null
+++ b/configs/SuperMicro/C7X58.conf
@@ -0,0 +1,66 @@
+# Contributed by Henrique de Moraes Holschuh.
+
+# Also compatible with X8SAX.
+
+
+#
+# Libsensors configuration for SuperMicro C7X58 and X8SAX boards, revision 1.1 or 2.0
+# Scaling factors kindly provided by SuperMicro support.
+# 
+# Board has two sensor chips, w83627dhg is not used for temperature,
+# fans or voltage sensing. sensors-detect will suggest that you load the
+# w83627ehf driver but you shouldn't.
+# BIOS allows one to set w83795adg parameters, such as voltage or PWM fan
+# control and default strategy.
+#
+
+chip "w83795adg-*"
+
+   label fan1 "CPU Fan"
+
+   label in0  "CPU Core"
+   label in2  "DIMM"
+   label in3  "+5V"
+   label in4  "+12V"
+   label in5  "-12V"
+   label in11 "VTT"
+   label in12 "+3.3V"
+   label in13 "+3.3Vsb"
+   label in14 "Vbatt"
+
+   # The BIOS does not set the correct limits for VTT, but it is wired.
+   # Default to broad limits used on Asus boards, feel free to refine for your CPU.
+   set in11_min 0.770
+   set in11_max 1.538
+
+   label temp6 "System temperature"
+   label temp7 "CPU temperature"
+
+   compute in3 @*4, @/4
+   compute in4 @*6.62, @/6.62
+   compute in5 (@-2.048)*24.2 + 2.048, (@-2.048)/24.2 + 2.048
+
+chip "w83627dhg-*"
+
+# SuperIO chip used only for the FDC, UARTs and GPIO
+# SENSORS ARE NOT WIRED
+# Power Supply Failure, GP31(From W83627DHG-P)    1 = Good, 0 = Bad
+
+   ignore fan1
+   ignore fan2
+   ignore fan3
+   ignore fan4
+   ignore fan5
+   ignore temp1
+   ignore temp2
+   ignore temp3
+   ignore in0
+   ignore in1
+   ignore in2
+   ignore in3
+   ignore in4
+   ignore in5
+   ignore in6
+   ignore in7
+   ignore in8
+   ignore cpu0_vid
diff --git a/configs/SuperMicro/DLE370.conf b/configs/SuperMicro/DLE370.conf
new file mode 100644
index 00000000..d268194f
--- /dev/null
+++ b/configs/SuperMicro/DLE370.conf
@@ -0,0 +1,55 @@
+# lm_sensors 3 configuration file for the Supermicro DLE370 motherboard
+# 2007-09-26, Jean Delvare <khali@linux-fr.org>
+# Comments welcome!
+
+chip "lm87-*"
+
+### Voltages
+
+   label in1  "Vcore"
+   label in2  "+3.3V"
+   label in3    "+5V"
+   label in4   "+12V"
+
+   # All voltage inputs are scaled internally, so the driver itself
+   # takes care of it.
+
+   set in1_min  cpu0_vid - 0.08
+   set in1_max  cpu0_vid + 0.08
+   set in2_min   3.3 * 0.95
+   set in2_max   3.3 * 1.05
+   set in3_min     5 * 0.95
+   set in3_max     5 * 1.05
+   set in4_min    12 * 0.95
+   set in4_max    12 * 1.05
+
+### Fans
+
+   label fan1  "CPU0 Fan"
+   label fan2  "CPU1 Fan"
+
+   set fan1_div 4
+   set fan2_div 4
+
+   set fan1_min 1800
+   set fan2_min 1800
+
+   # Unfortunately, the analog output appears not to be wired to anything
+   # so there is no way to control the fan speeds.
+
+### Temperatures
+
+   label temp1   "Sys Temp"
+   label temp2  "CPU0 Temp"
+   label temp3  "CPU1 Temp"
+
+   # The BIOS will set the temperature limits to reasonable values, so
+   # you can leave them as is. I tend to prefer more restrictive settings
+   # though.
+
+   set temp1_min   5
+   set temp1_max  48
+   set temp2_min   5
+   set temp2_max  56
+   set temp3_min   5
+   set temp3_max  56
diff --git a/configs/SuperMicro/H8DC8.conf b/configs/SuperMicro/H8DC8.conf
new file mode 100644
index 00000000..e8241330
--- /dev/null
+++ b/configs/SuperMicro/H8DC8.conf
@@ -0,0 +1,138 @@
+# Example configuration for the SuperMicro H8DC8.
+# Contributed by Romain Dolbeau.
+
+
+# settings for the supermicro H8DC8
+# here are the details supplied by the technical support:
+##Bus Type = SMBus
+##One WindBond W83627HF, One Analog Devices ADM1026
+##
+##Analog Devices ADM1026, Slave Address=0x2c (0x58 in 8-Bit format)
+##==============================================================
+##Fan1 Fan Speed, Offset 0x38           RPM=1350000/8/Reading
+##Fan2 Fan Speed, Offset 0x39           RPM=1350000/8/Reading
+##Fan3 Fan Speed, Offset 0x3a           RPM=1350000/8/Reading
+##Fan4 Fan Speed, Offset 0x3b           RPM=1350000/8/Reading
+##Fan5 Fan Speed, Offset 0x3c           RPM=1350000/8/Reading
+##Fan6 Fan Speed, Offset 0x3d           RPM=1350000/8/Reading
+##Fan7 Fan Speed, Offset 0x3e           RPM=1350000/8/Reading
+##Fan8 Fan Speed, Offset 0x3f           RPM=1350000/8/Reading
+##CPU1 Core Voltage, Offset 0x2d        Voltage=(Reading * 3)/256
+##CPU2 Core Voltage, Offset 0x37        Voltage=(Reading * 2.5)/256
+##+5VSB Voltage, offset 0x30            Voltage=(Reading * 6)/256
+##+1.5V Voltage, offset 0x32            Voltage=(Reading * 3)/256
+##+5V Voltage, offset 0x2c              Voltage=(Reading * 6.66)/256
+##+12V Voltage, offset 0x2e             Voltage=(Reading * 16)/256
+##-12V Voltage, offset 0x2f             Voltage=((Reading* 18.5)/256)-16
+##DIMM Voltage, offset 0x33             Voltage=(Reading * 3)/256
+##Battery Voltage, Offset 0x26
+##Voltage=(((Reading-128)*2)/128)+2)
+##System Temperature, Offset 0x1f       C=Reading
+##CPU1 Temperature, Offset 0x28         C=Reading
+##CPU2 Temperature, Offset 0x29         C=Reading
+##Chassis Intrusion, Offset 0x23, BitMask=40
+##
+##
+##Power Supply Failure (From W82627HF), GP12
+#
+# Notes:
+# 1) no section for the W82627HF yet.
+# 2) the temperature min/max are ballpark estimate,
+#    you may need to fix them depening on your environment
+#    such as the setting of your air conditionner.
+# 3) According to the support, in11 and in12 (both +3.3V
+#    lines) aren't hooked up, yet they supply proper readings
+#    (as specified by the manufacturer of the chip for those
+#    lines).
+#    You may want to disable them.
+#
+# Originally written by Romain Dolbeau <romain@dolbeau.org>
+# Uses at your own risk !
+
+chip "adm1026-i2c-*-2c"
+
+  label fan0 "FAN0 Speed"
+  label fan1 "FAN1 Speed"
+  label fan2 "FAN2 Speed"
+  label fan3 "FAN3 Speed"
+  label fan4 "FAN4 Speed"
+  label fan5 "FAN5 Speed"
+  label fan6 "FAN6 Speed"
+  label fan7 "FAN7 Speed"
+
+  set fan0_div 8
+  set fan1_div 8
+  set fan2_div 8
+  set fan3_div 8
+  set fan4_div 8
+  set fan5_div 8
+  set fan6_div 8
+  set fan7_div 8
+
+  label in0 "+5VSB Voltage"
+  compute in0 @*2,@/2
+  set in0_min 5*0.90
+  set in0_max 5*1.1
+
+  ignore in1
+
+  label in2 "+1.5V Voltage"
+  set in2_min 1.5*0.95
+  set in2_max 1.5*1.05
+
+  label in3 "DIMM Voltage"
+  set in3_min 2.5*0.95
+  set in3_max 2.5*1.05
+
+  ignore in4
+  ignore in5
+  ignore in6
+
+  label in7 "CPU2 Core Voltage"
+  set in7_min 1.35*0.95
+  set in7_max 1.35*1.05
+
+  ignore in8
+  ignore in9
+
+  label in10 "Battery Voltage"
+  set in10_min 3*0.95
+  set in10_max 3*1.05
+
+  # for in11 & in12, see comments above
+  #ignore in11
+  #ignore in12
+
+  label in11 "3.3V Standby"
+  set in11_min 3.3*0.95
+  set in11_max 3.3*1.05
+
+  label in12 "3.3V Main"
+  set in12_min 3.3*0.95
+  set in12_max 3.3*1.05
+
+  label in13 "+5V Voltage"
+  set in13_min 5*0.95
+  set in13_max 5*1.05
+
+  label in14 "CPU1 Core Voltage"
+  set in14_min 1.35*0.95
+  set in14_max 1.35*1.05
+
+  label in15 "+12V Voltage"
+  set in15_min 12*0.95
+  set in15_max 12*1.05
+
+  label in16 "-12V Voltage"
+  set in16_max -12*0.95
+  set in16_min -12*1.05
+
+  label temp1 "System Temperature"
+  set temp1_min 18
+  set temp1_max 40
+  label temp2 "CPU1 Temperature"
+  set temp2_min 20
+  set temp2_max 45
+  label temp3 "CPU2 Temperature"
+  set temp3_min 20
+  set temp3_max 45
diff --git a/configs/SuperMicro/H8QM3.conf b/configs/SuperMicro/H8QM3.conf
new file mode 100644
index 00000000..dafec2ed
--- /dev/null
+++ b/configs/SuperMicro/H8QM3.conf
@@ -0,0 +1,30 @@
+# Sensors-detect will suggest loading the w83627hf driver, but don't, it's
+# useless on this board.
+
+
+chip "w83793-i2c-*-2f"
+
+   # Voltages
+   label  in0  "Vcore1"
+   label  in1  "Vcore2"
+   ignore in2
+   label  in3  "Vcore4"
+   label  in4  "Vcore3"
+   label  in5  "+3.3V"
+   label  in6  "+12V"
+
+   compute  in6  @*12, @/12
+
+   # Fans
+   label  fan3  "CPU2 Fan"
+   label  fan4  "CPU1 Fan"
+   label  fan7  "CPU4 Fan"
+   label  fan8  "CPU3 Fan"
+
+   # Temperatures
+   label  temp1  "CPU1 Temp"
+   label  temp2  "CPU2 Temp"
+   label  temp3  "CPU4 Temp"
+   label  temp4  "CPU3 Temp"
+   label  temp5  "Sys Temp"
+   # Not sure about temp6
diff --git a/configs/SuperMicro/PDSMi+.conf b/configs/SuperMicro/PDSMi+.conf
new file mode 100644
index 00000000..f64c3cfe
--- /dev/null
+++ b/configs/SuperMicro/PDSMi+.conf
@@ -0,0 +1,82 @@
+# Example configuration for the SuperMicro PDSMi+.
+# Contributed by Romain Dolbeau & Jean Delvare
+
+
+# settings for the supermicro PDSMi+
+#
+# Notes:
+# 1) You need lm-sensors >= 2.10.2, otherwise you get an error about
+#    missing temp6.
+#
+# Originally written by Romain Dolbeau <romain@dolbeau.org>
+# Uses at your own risk !
+chip "w83793-i2c-*-2f"
+
+# 0x10, CPU Core
+    label in0 "CPU Core"
+# 0x11, unconnected according to support, 1.5V in BIOS ?
+    label in1 "+1.5V"
+    set in1_min 1.5*0.95
+    set in1_max 1.5*1.05
+# 0x12, unconnected according to support, VTT=1.2V in BIOS ?
+    label in2 "VTT"
+    set in2_min 1.2*0.95
+    set in2_max 1.2*1.05
+# 0x14, -12V
+    label in3 "-12V"
+#    From Supermicro support information...
+#    compute in3 (((@/8)*18500)/256)-16, (((@+16)*256)/18500)*8
+#    ... but this from Jean Delvare works better in pratice
+    compute in3 (@ * 5.14) - 14.91, (@ + 14.91) / 5.14
+    set in3_min -12*1.05
+    set in3_max -12*0.95
+# 0x15, DIMM
+    label in4 "DIMM"
+# 0x16, +3.3V
+    label in5 "+3.3V"
+    set in5_min 3.3*0.95
+    set in5_max 3.3*1.05
+# 0x17, +12V
+    label in6 "+12V"
+    compute in6 @*12,@/12
+    set in6_min 12*0.95
+    set in6_max 12*1.05
+# Ox18, +5V
+    label in7 "+5V"
+    compute in7 @-0.15,@+0.15
+    set in7_min 5*0.95
+    set in7_max 5*1.05
+# 0x19, 5VSB
+    label in8 "5VSB"
+    compute in8 @-0.15,@+0.15
+    set in8_min 5*0.95
+    set in8_max 5*1.05
+# 0x1a, Battery Voltage
+    label in9 "VBAT"
+
+    label temp1 "CPU Temp"
+    ignore temp2
+    ignore temp3
+    ignore temp4
+# System Temp used to live at temp5, but was moved to temp6 for some reason
+    ignore temp5
+#    label temp5 "System Temp"
+#    ignore temp6
+    label temp6 "System Temp"
+
+# 6 connected
+    label fan1 "fan1"
+    label fan2 "fan2"
+    label fan3 "fan3"
+    label fan4 "fan4"
+    label fan5 "fan5"
+# apparently, fan6 is skipped and fan7 is used instead for CPU fan,
+# at least that's how I understand Supermicro data.
+    ignore fan6
+    label fan7 "CPU fan"
+    ignore fan8
+    ignore fan9
+    ignore fan10
+    ignore fan12
+    ignore fan12
+# you should ignore the last 3 or 4, in 1U rackmount system
diff --git a/configs/SuperMicro/X6DH8-XG2.conf b/configs/SuperMicro/X6DH8-XG2.conf
new file mode 100644
index 00000000..03c36bb2
--- /dev/null
+++ b/configs/SuperMicro/X6DH8-XG2.conf
@@ -0,0 +1,30 @@
+# Partial and untested configuration file for the SuperMicro X6DH8-XG2.
+# Please report if you try it.
+
+
+chip "pc87427-*"
+
+   label  fan7  "CPU1 Fan"
+   label  fan8  "CPU2 Fan"
+
+chip "lm93-*"
+
+   ignore fan1
+   ignore fan2
+   ignore fan3
+   ignore fan4
+
+   label  in1  "+12V"
+   label  in7  "VCore1"
+   label  in8  "VCore2"
+   label  in9  "+3.3V"
+   label  in10 "+5V"
+   ignore in11
+   label  in15 "-12V"
+
+   compute in1  @ * ((13.7/1.15)+1), @ / ((13.7/1.15)+1)
+   compute in15 @ * 5.1138 - 13.5771, (@ + 13.5771) / 5.1138
+
+   label  temp1  "CPU1 Temp"
+   label  temp2  "CPU2 Temp"
+   label  temp3  "Sys Temp"
diff --git a/configs/SuperMicro/X7DB8.conf b/configs/SuperMicro/X7DB8.conf
new file mode 100644
index 00000000..782ba972
--- /dev/null
+++ b/configs/SuperMicro/X7DB8.conf
@@ -0,0 +1,121 @@
+# Originally contributed by Gary E. Miller, cleaned up by Jean Delvare.
+
+
+# /etc/sensors.d/X7DB8
+# settings for the supermicro X7DB8
+# originally written by Gary E. Miller <gem@rellim.com>
+# use at your own risk !
+# Date: 30 May 2012
+
+# Here's the info as supplied by Supermicro:
+#
+# Bus Type = SMBus
+# One W83793G
+# 
+# Windbond W83793G, Slave Address=0x2f (0x5E in 8-Bit format)
+# =============================================================
+# Fan1 Fan Speed, Offset 0x23, 0x24			RPM = 1350000/Data
+# Fan2 Fan Speed, Offset 0x25, 0x26			RPM = 1350000/Data
+# Fan3 Fan Speed, Offset 0x27, 0x28			RPM = 1350000/Data
+# Fan4 Fan Speed, Offset 0x29, 0x2a			RPM = 1350000/Data
+# Fan5 Fan Speed, Offset 0x2b, 0x2c			RPM = 1350000/Data
+# Fan6 Fan Speed, Offset 0x2d, 0x2e			RPM = 1350000/Data
+# Fan7/CPU1 Fan Speed, Offset 0x2f, 0x30		RPM = 1350000/Data
+# Fan8/CPU2 Fan Speed, Offset 0x31, 0x32		RPM = 1350000/Data
+# CPU1 Core Voltage, Offset 0x10			Voltage = Data* 0.008	
+# CPU2 Core Voltage, Offset 0x11			Voltage = Data* 0.008
+# -12V Voltage, Offset 0x14				Voltage = ((Data*0.016)- (2.048*(232./260.)))/(1-(232./260.))
+# +1.5V Voltage, Offset 0x15				Voltage = Data* 0.016
+# +3.3V Voltage, Offset 0x16				Voltage = Data* 0.016
+# +12V Voltage, Offset 0x17				Voltage = Data* 0.008/ (10./120.)
+# +5V Voltage, Offset 0x18				Voltage = Data* 0.024
+# 5Vsb Voltage, Offset 0x19				Voltage = Data* 0.024
+# Battery Voltage, Offset 0x1a				Voltage = Data* 0.016
+# CPU1 CoreA (PECI Agent1) Temperature, Offset 0x1c	Temperature = Data
+# CPU1 CoreB (PECI Agent2) Temperature, Offset 0x1d	Temperature = Data
+# CPU2 CoreA (PECI Agent3) Temperature, Offset 0x1e	Temperature = Data
+# CPU2 CoreB (PECI Agent4) Temperature, Offset 0x1f	Temperature = Data
+# System Temperature, Offset 0x20			Temperature = Data
+# Chassis Intrusion, Offset 0x44, BitMask 0x40		1 = Bad, 0 = Good
+# 
+# 
+# Windbond W83627HF
+# =============================================================
+# Power Supply Failure, GP11(From W83627HF)		1 = Good, 0 = Bad
+#
+
+chip "w83627hf-isa-0290"
+    # no driver access to GP11, so I turned off everything.
+    ignore in0
+    ignore in1
+    ignore in2
+    ignore in3
+    ignore in4
+    ignore in5
+    ignore in6
+    ignore in7
+    ignore in8
+    ignore cpu0_vid
+    ignore fan1
+    ignore fan2
+    ignore fan3
+    ignore temp1
+    ignore temp2
+    ignore temp3
+
+
+
+bus "i2c-0" "SMBus I801 adapter at 1100"
+
+chip "w83793-i2c-0-2f"
+
+	label fan7	"CPU1 Fan"
+	label fan8	"CPU2 Fan"
+
+# Voltages ; note that in the table above, the .008, .016, and .024 factors are
+# already computed in the driver...
+	label in0 "Vcore1"
+	label in1 "Vcore2"
+	ignore in2
+	label in3 "-12V"
+	label in4 "+1.5V"
+	label in5 "+3.3V"
+	label in6 "+12V"
+	label in7 "+5V"
+	label in8 "5Vsb"
+	label in9 "Vbat"
+
+	label temp1 "CPU1 CoreA"
+	label temp2 "CPU1 CoreB"
+	label temp3 "CPU2 CoreA"
+	label temp4 "CPU2 CoreB"
+	label temp5 "M/B Temp"
+
+	compute in3  (@ - (2.048*(232/260)))/(1-(232/260)), (@*(1-(232/260)))+(2.048*(232/260))
+	compute in6  @ * 12 , @ / 12
+
+
+	# CPUs
+	set in0_min  0.82
+	set in0_max  1.35
+	set in1_min  0.82
+	set in1_max  1.35
+
+	# -12V, 10%
+	set in3_max  -12.0 * 0.90
+	set in3_min  -12.0 * 1.10
+	# +3.3V, 5%
+	set in5_min  3.3 * 0.95
+	set in5_max  3.3 * 1.05
+	# +12V, 5%
+	set in6_min  12.0 * 0.95
+	set in6_max  12.0 * 1.05
+	# +5V, 5%
+	set in7_min  5.0 * 0.95
+	set in7_max  5.0 * 1.05
+	# 5Vsb, 10%
+	set in8_min  5.0 * 0.90
+	set in8_max  5.0 * 1.10
+	# Vbat, 10%
+	set in9_min  3.0 * 0.90
+	set in9_max  3.0 * 1.10
diff --git a/configs/SuperMicro/X7DBE.conf b/configs/SuperMicro/X7DBE.conf
new file mode 100644
index 00000000..2e970ca7
--- /dev/null
+++ b/configs/SuperMicro/X7DBE.conf
@@ -0,0 +1,65 @@
+# settings for the SuperMicro X7DBE
+#
+# Notes:
+# 1) You need lm-sensors >= 2.10.2, otherwise you get an error about
+#    missing temp6.
+#
+# Originally written by Romain Dolbeau <romain@dolbeau.org>
+# Use at your own risk!
+
+chip "w83793-i2c-*-2f"
+
+# 0x10, CPU Core 1
+    label in0 "CPU Core 1"
+# 0x11, CPU Core 2
+    label in1 "CPU Core 2"
+# 0x12 VTT=1.2V in BIOS ?
+    label in2 "VTT"
+    set in2_min 1.2*0.95
+    set in2_max 1.2*1.05
+# 0x14, -12V
+    label in3 "-12V"
+    compute in3 (((@/8)*18500)/256)-16, (((@+16)*256)/18500)*8
+    set in3_min -12*1.05
+    set in3_max -12*0.95
+# 0x15, DIMM
+    label in4 "P1V5"
+# 0x16, +3.3V
+    label in5 "+3.3V"
+    set in5_min 3.3*0.95
+    set in5_max 3.3*1.05
+# 0x17, +12V
+    label in6 "+12V"
+    compute in6 @*12,@/12
+    set in6_min 12*0.95
+    set in6_max 12*1.05
+# Ox18, +5V
+    label in7 "+5V"
+    set in7_min 5*0.95
+    set in7_max 5*1.05
+# 0x19, 5VSB
+    label in8 "5VSB"
+    set in8_min 5*0.95
+    set in8_max 5*1.05
+# 0x1a, Battery Voltage
+    label in9 "VBAT"
+
+    label temp1 "CPU1 Temp"
+    label temp2 "CPU2 Temp"
+    ignore temp3
+    ignore temp4
+    label temp5 "System Temp"
+    ignore temp6
+
+    label fan1 "fan1"
+    label fan2 "fan2"
+    label fan3 "fan3"
+    label fan4 "fan4"
+    ignore fan5
+    ignore fan6
+    label fan7 "CPU1 fan"
+    label fan8 "CPU2 fan"
+    ignore fan9
+    ignore fan10
+    ignore fan11
+    ignore fan12
diff --git a/configs/SuperMicro/X7SBU.conf b/configs/SuperMicro/X7SBU.conf
new file mode 100644
index 00000000..58e36976
--- /dev/null
+++ b/configs/SuperMicro/X7SBU.conf
@@ -0,0 +1,108 @@
+# Example configuration for the SuperMicro X7SBU. Contributed by Joe Ogulin.
+
+# Monitoring hardware on this board: Winbond W83793G on ICH9 SMBus (driver
+# w83793) and integrated sensors in the CPU (driver coretemp). A few voltages
+# also available from the Winbond W83627HF Super-I/O chip.
+
+
+# settings for the supermicro X7SBU
+#
+chip "w83793-*"
+
+# 0x10, CPU Core
+    label in0 "CPU Core"
+# 0x11, unconnected according to support, 1.5V in BIOS ?
+    label in1 "+1.25V"
+    set in1_min 1.25*0.95
+    set in1_max 1.25*1.05
+# 0x12, unconnected according to support, VTT=1.2V in BIOS ?
+    label in2 "VTT"
+# 0x14, -12V
+    label in3 "-12V"
+#    From Supermicro support information...
+#    compute in3 (((@/8)*18500)/256)-16, (((@+16)*256)/18500)*8
+#    ... but this from Jean Delvare works better in pratice
+    compute in3 (@ * 5.14) - 14.91, (@ + 14.91) / 5.14
+    set in3_min -12*1.05
+    set in3_max -12*0.95
+# 0x15, DIMM
+    label in4 "DIMM"
+# 0x16, +3.3V
+    label in5 "+3.3V"
+    set in5_min 3.3*0.95
+    set in5_max 3.3*1.05
+# 0x17, +12V
+    label in6 "+12V"
+    compute in6 @*12,@/12
+    set in6_min 12*0.95
+    set in6_max 12*1.05
+# Ox18, +5V
+    label in7 "+5V"
+    compute in7 @-0.15,@+0.15
+    set in7_min 5*0.95
+    set in7_max 5*1.05
+# 0x19, 5VSB
+    label in8 "5VSB"
+    compute in8 @-0.15,@+0.15
+    set in8_min 5*0.95
+    set in8_max 5*1.05
+# 0x1a, Battery Voltage
+    label in9 "VBAT"
+
+    label temp1 "CPU Temp"
+    ignore temp2
+    ignore temp3
+    ignore temp4
+    label temp5 "Sys Temp"
+    ignore temp6
+
+# 3 connected
+# note that these fan labels are for a 1U rackmount and are given their
+# positions based on where they are when you look at it from the front
+# towards the back
+#
+# relabel them as necessary to however you have them set up
+    label fan1 "Right Fan"
+    label fan2 "Mid-right Fan"
+    label fan3 "Middle Fan"
+    ignore fan4
+    ignore fan5
+    ignore fan6
+    ignore fan7
+    ignore fan8
+    ignore fan9
+    ignore fan10
+    ignore fan12
+    ignore fan12
+    # Override CPU temperature threshold
+    set temp1_max       80
+    set temp1_max_hyst  70
+
+    set temp5_max       60
+    set temp5_max_hyst  55
+
+# NOTE: nearly everything on this chip is not used you can turn on alarms, if
+# you have the appropriate setup for it and want to have chassis intrusion
+# detection turned on
+
+chip "w83627hf-*"
+
+    ignore in0
+    ignore in1
+    ignore in2
+    label in3 "+5.0V"
+    compute in3 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)
+    set in3_min 5*0.95
+    set in3_max 5*1.05
+    ignore in4
+    ignore in5
+    ignore in6
+    ignore in7
+    ignore in8
+    ignore fan1
+    ignore fan2
+    ignore fan3
+    ignore alarms
+    ignore temp1
+    ignore temp2
+    ignore temp3
diff --git a/configs/SuperMicro/X7SBi.conf b/configs/SuperMicro/X7SBi.conf
new file mode 100644
index 00000000..e82f3d64
--- /dev/null
+++ b/configs/SuperMicro/X7SBi.conf
@@ -0,0 +1,108 @@
+# Example configuration for the SuperMicro X7SBi. Contributed by Joe Ogulin.
+
+# Monitoring hardware on this board: Winbond W83793G on ICH9 SMBus (driver
+# w83793) and integrated sensors in the CPU (driver coretemp). A few voltages
+# also available from the Winbond W83627HF Super-I/O chip.
+
+
+# settings for the supermicro X7SBi
+#
+chip "w83793-*"
+
+# 0x10, CPU Core
+    label in0 "CPU Core"
+# 0x11, unconnected according to support, 1.5V in BIOS ?
+    label in1 "+1.5V"
+    set in1_min 1.5*0.95
+    set in1_max 1.5*1.05
+# 0x12, unconnected according to support, VTT=1.2V in BIOS ?
+    label in2 "VTT"
+    set in2_min 1.2*0.95
+    set in2_max 1.2*1.05
+# 0x14, -12V
+    label in3 "-12V"
+#    From Supermicro support information...
+#    compute in3 (((@/8)*18500)/256)-16, (((@+16)*256)/18500)*8
+#    ... but this from Jean Delvare works better in pratice
+    compute in3 (@ * 5.14) - 14.91, (@ + 14.91) / 5.14
+    set in3_min -12*1.05
+    set in3_max -12*0.95
+# 0x15, DIMM
+    label in4 "DIMM"
+# 0x16, +3.3V
+    label in5 "+3.3V"
+    set in5_min 3.3*0.95
+    set in5_max 3.3*1.05
+# 0x17, +12V
+    label in6 "+12V"
+    compute in6 @*12,@/12
+    set in6_min 12*0.95
+    set in6_max 12*1.05
+# Ox18, +5V
+    label in7 "+5V"
+    compute in7 @-0.15,@+0.15
+    set in7_min 5*0.95
+    set in7_max 5*1.05
+# 0x19, 5VSB
+    label in8 "5VSB"
+    compute in8 @-0.15,@+0.15
+    set in8_min 5*0.95
+    set in8_max 5*1.05
+# 0x1a, Battery Voltage
+    label in9 "VBAT"
+
+    label temp1 "CPU Temp"
+    ignore temp2
+    ignore temp3
+    ignore temp4
+    ignore temp5
+    label temp6 "Sys Temp"
+
+# 3 connected
+# note that these fan labels are for a 1U rackmount and are given their
+# positions based on where they are when you look at it from the front
+# towards the back
+#
+# relabel them as necessary to however you have them set up
+    label fan1 "Right Fan"
+    ignore fan2
+    ignore fan3
+    ignore fan4
+    label fan5 "Mid-right Fan"
+    ignore fan6
+    label fan7 "Middle Fan"
+    ignore fan8
+    ignore fan9
+    ignore fan10
+    ignore fan12
+    ignore fan12
+    # Override CPU temperature threshold
+    set temp1_max       80
+    set temp1_max_hyst  70
+
+    set temp6_max       60
+    set temp6_max_hyst  55
+
+# NOTE: nearly everything on this chip is not used you can turn on alarms, if
+# you have the appropriate setup for it and want to have chassis intrusion
+# detection turned on
+
+chip "w83627hf-*"
+
+    ignore in0
+    ignore in1
+    ignore in2
+    label in3 "+5.0V"
+    compute in3 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)
+    ignore in4
+    ignore in5
+    ignore in6
+    ignore in7
+    ignore in8
+    ignore fan1
+    ignore fan2
+    ignore fan3
+    ignore alarms
+    ignore temp1
+    ignore temp2
+    ignore temp3
diff --git a/configs/SuperMicro/X7SLA.conf b/configs/SuperMicro/X7SLA.conf
new file mode 100644
index 00000000..b8d81cf0
--- /dev/null
+++ b/configs/SuperMicro/X7SLA.conf
@@ -0,0 +1,39 @@
+# Contributed by Jeff Rickman, fixes by Jean Delvare.
+
+
+chip "w83627dhg-*"
+
+    label in0 "Vcore"
+    label in1 "+12V"
+    label in2 "+3.3V"
+    label in3 "Vcc"
+    label in4 "Vdimm"
+    label in5 "+5V"
+    label in6 "+1.5V"
+    label in7 "3VSB"
+    label in8 "Vbat"
+
+    label fan1 "Back Fan"
+    label fan2 "P/S Fan"
+    label fan5 "Front Fan"
+    label fan4 "MCH Fan"
+
+    label temp1 "M/B Temp"
+    label temp2 "CPU Temp"
+
+    ignore fan3
+    ignore cpu0_vid
+    ignore temp3
+
+    # Scaling factor for +12V needs confirmation
+    compute in1  @*6.63, @/6.63
+    compute in5  @*4, @/4
+
+    set in2_min  3.3 * 0.90
+    set in2_max  3.3 * 1.10
+    set in3_min  3.3 * 0.90
+    set in3_max  3.3 * 1.10
+    set in7_min  3.3 * 0.90
+    set in7_max  3.3 * 1.10
+    set in8_min  3.0 * 0.90
+    set in8_max  3.0 * 1.10
diff --git a/configs/SuperMicro/X7SPA.conf b/configs/SuperMicro/X7SPA.conf
new file mode 100644
index 00000000..08a4478d
--- /dev/null
+++ b/configs/SuperMicro/X7SPA.conf
@@ -0,0 +1,32 @@
+# Configuration file contributed by Scott Shanafelt.
+
+
+chip "w83627dhg-*"
+
+	label in0 "Vcore"
+	label in1 "+1.05V"
+	label in2 "AVCC"
+	label in3 "3VCC"
+		set in3_min 3.3 * 0.90
+		set in3_max 3.3 * 1.10
+	label in4 "Vdimm"
+	label in5 "+5V"
+		compute in5 @*4, @/4
+	label in6 "+12V"
+		compute in6 @*16, @/16
+		set in6_min 12 * 0.90
+		set in6_max 12 * 1.10
+	label in7 "3VSB"
+	label in8 "Vbat"
+
+	ignore fan1
+	label fan2 "CPU Fan"
+	ignore fan3
+	label fan4 "Case Fan"
+	ignore fan5
+
+	label temp1 "MB Temp"
+	label temp2 "CPU Temp"
+	label temp3 "Case Temp"
+
+	ignore cpu0_vid
diff --git a/configs/SuperMicro/X8DTN.conf b/configs/SuperMicro/X8DTN.conf
new file mode 100644
index 00000000..ee052349
--- /dev/null
+++ b/configs/SuperMicro/X8DTN.conf
@@ -0,0 +1,100 @@
+# /etc/sensors.d/X8DTN
+# settings for the supermicro X8DTN
+# originally written by Gary E. Miller <gem@rellim.com>
+# use at your own risk !
+# Date: 25 May 2012
+
+# Here's the info as supplied by Supermicro:
+
+#
+# Bus Type = ISAIO/SMBus
+# One W83795AG
+# 
+# Windbond W83795AG, Slave Address=0x2f (0x5E in 8-Bit format)
+# =============================================================
+# Fan1 Fan Speed, Offset 0x2e		RPM = 84375/Data
+# Fan2 Fan Speed, Offset 0x2f		RPM = 84375/Data
+# Fan3 Fan Speed, Offset 0x30		RPM = 84375/Data
+# Fan4 Fan Speed, Offset 0x31		RPM = 84375/Data
+# Fan5 Fan Speed, Offset 0x32		RPM = 84375/Data
+# Fan6 Fan Speed, Offset 0x33		RPM = 84375/Data
+# Fan7 Fan Speed, Offset 0x34		RPM = 84375/Data
+# Fan8 Fan Speed, Offset 0x35		RPM = 84375/Data
+# CPU1 Voltage, Offset 0x10		Voltage = Data* 0.008
+# CPU2 Voltage, Offset 0x11		Voltage = Data* 0.008
+# +1.5V Voltage, Offset 0x12		Voltage = Data* 0.008
+# +5V Voltage, Offset 0x13		Voltage = Data* 0.008 * (40/10)
+# +12V Voltage, Offset 0x14		Voltage = Data* 0.008/ (10./66.2)
+# +5VSB Voltage, Offset 0x15		Voltage = Data* 0.008 * (40/10)
+# +3.3V Voltage, Offset 0x1c		Voltage = Data* 0.024
+# +3.3VSB Voltage, Offset 0x1d		Voltage = Data* 0.024
+# Battery Voltage, Offset 0x1e		Voltage = Data* 0.024
+# CPU1 Temperature, Offset 0x27		Temperature = Data
+# CPU2 Temperature, Offset 0x26		Temperature = Data
+# System Temperature, Offset 0x1f		Temperature = Data
+# Chassis Intrusion, Bank 0, Offset 0x46, BitMask 0x40	1 = Bad, 0 = Good
+#		 (Clear Bit: Bank 0, Offset 0x4d, BitMask 0x80)
+# 
+# 
+# Power Supply Failure, GP11(From W83627HF)		1 = Good, 0 = Bad
+ 
+chip "w83627hf-isa-0a00"
+    # I'm not sure which is GP11, so I turned off everything.
+    ignore in0
+    ignore in1
+    ignore in2
+    ignore in3
+    ignore in4
+    ignore in5
+    ignore in6
+    ignore in7
+    ignore in8
+    ignore cpu0_vid
+    ignore fan1
+    ignore fan2
+    ignore fan3
+    ignore temp1
+    ignore temp2
+    ignore temp3
+ 
+bus "i2c-0" "SMBus I801 adapter at 0400"
+
+chip "w83795adg-i2c-0-2f"
+
+# Voltages ; note that in the table above, the .008 and .024 factors are
+# already computed in the driver...
+
+    label in0 "CPU1"
+    label in1 "CPU2"
+    label in2 "+1.5V"
+    label in3 "+5V"
+    label in4 "+12V"
+    label in5 "5VSB"
+    label in12 "+3.3V"
+    label in13 "3VSB"
+    label in14 "Vbat"
+
+    compute in3 @*4, @/4
+    compute in4 @*6.62, @/6.62
+    compute in5 @*4, @/4
+
+    label temp5 "mobo"
+    label temp7 "CPU2"
+    label temp8 "CPU1"
+
+    ignore in6
+    ignore in7
+    ignore in11
+    ignore temp3
+    ignore temp4
+
+    set in0_min  0.82
+    set in0_max  1.35
+    set in1_min  0.82
+    set in1_max  1.35
+    set in12_min  3.3 * 0.90
+    set in12_max  3.3 * 1.05
+    set in13_min  3.3 * 0.95
+    set in13_max  3.3 * 1.10
+    set in14_min  3.0 * 0.90
+    set in14_max  3.3 * 1.10
diff --git a/configs/SuperMicro/X9SRA.conf b/configs/SuperMicro/X9SRA.conf
new file mode 100644
index 00000000..04d8c89a
--- /dev/null
+++ b/configs/SuperMicro/X9SRA.conf
@@ -0,0 +1,56 @@
+# Configuration file contributed by Eric Wedel.
+
+
+# Supermicro X9SRA motherboard lm-sensors configuration.
+# Voltage inputs & scaling per Supermicro support.  Other
+# inputs from BIOS screen and observation.
+
+chip "nct6776-*"
+
+### Voltages
+
+label in0 "Vcore"
+
+label in1 "+12V"
+compute in1 @ * (66.2/10), @ / (66.2/10)
+
+label in2 "AVcc"
+
+label in3 "+3.3V"
+
+label in4 "Vdimm"
+
+label in5 "+5V"
+compute in5 @ * 4, @ / 4
+
+label in6 "Vtt"
+
+label in7 "+3.3Vsb"
+
+label in8 "Vbatt"
+
+### Temperatures
+
+# not sure about temp1 / temp2 assignments
+
+label temp1 "System temperature"
+label temp2 "Peripheral temperature"
+
+ignore temp3
+
+# PECI agent 0:
+label temp7 "CPU temperature"
+
+label temp8 "PCH temperature"
+
+ignore temp9
+ignore temp10
+
+## fans: gratuitous renumbering between Supermicro & lm-sensors.
+## Use display labels which match X9SRA fan connector labels.
+
+label fan1  "fanA"
+label fan2  "fan1"
+label fan3  "CPU Fan"
+label fan4  "fan3"
+label fan5  "Exhaust Fan"
diff --git a/configs/Tyan/S2466-4M.conf b/configs/Tyan/S2466-4M.conf
new file mode 100644
index 00000000..2690790a
--- /dev/null
+++ b/configs/Tyan/S2466-4M.conf
@@ -0,0 +1,109 @@
+#    Sensors configuration file used by 'libsensors' for Tyan S2466-4M
+#
+# Edited by: kevin schlichter <kevins at tyan dot com> 05.16.03
+# Update 07.30.03:kevin schlichter: add vid support
+# Update 2009-Apr-01 Adam Thompson <athompso at athompso dot net>: radically 
+#   updated for lm_sensors 3.0.2 & Linux kernel 2.6.27 (aka Ubuntu 8.10)
+#
+# Note that in the 2.6 series of kernels, with lm_sensors 3.0.2, it is
+# no longer necessary to jump through force_subclient= and ignore_* hoops
+# when loading the w83782d module; its default behaviour is sufficient
+# to support itself correctly (and it finds the 3 subclients without any
+# additional prompting).  This does NOT allow access to the other chip,
+# a W83627HF, over I2C, but this second chip is mapped into the ISA I/O 
+# space anyway, and loading the "w83627hf" module without any options 
+# locates it and accesses it perfectly fine.  See also notes below about
+# the inadvisability of overusing the I2C bus on this motherboard anyway.
+# This has only been tested on MY board, which is the -4M variant, with
+# BIOS 4.06.  Depending on your BIOS version, you may or may not want to 
+# use the "init=0" module options INSTEAD OF setting various mins & maxes 
+# below, particularly temperature-wise.  YMMV.
+# -Adam Thompson, 2009-Apr-01
+#####
+
+# set min/max limits to  5% for the critical voltages
+# set min/max limits to 10% for the non-critical voltages
+# set min/max limits to 20% for the battery voltage
+
+
+chip "w83782d-*"
+    ignore  in0 
+    ignore  in1
+    label   in2 "AGP V"
+    set     in2_min 3.3*0.95
+    set     in2_max 3.3*1.05
+    label   in3 " +5 V"
+    compute in3 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)
+    set     in3_min 5.0*0.95
+    set     in3_max 5.0*1.05
+    label   in4 "DDR V"
+    ignore  in5
+    ignore  in7
+    label   in6 "3 VSB"
+    set     in6_max 3.0*1.05
+    set     in6_min 3.0*0.95
+    label   in8 "Bat V"
+    set     in8_min 3.3*0.80
+    set     in8_max 3.3*1.20
+    ignore  vid
+    label   fan1 "Chassis Fan 2"
+    label   fan2 "Chassis Fan 1"
+    label   fan3 "PSU Fan"
+    label   temp1 "VRM2 Temp"
+    label   temp2 "CPU1 Temp"
+    label   temp3 "CPU2 Temp"
+#    set     temp1_type 2
+#    set     temp1_max 40	
+#    set     temp1_max_hyst 60	
+#    set     temp2_type 2
+#    set     temp2_max 70	
+#    set     temp2_max_hyst 80	
+#    set     temp3_type 2
+#    set     temp3_max 70	
+#    set     temp3_max_hyst 80	
+
+# lm_sensors ticket#1795 (http://www.lm-sensors.org/ticket/1795) also 
+# strongly suggests using the ISA bus where possible to avoid overloading
+# the SMBus on Tyan motherboards.
+# Accessing this via ISA inb/outb also avoids the need altogether to use
+# force_subclient= options when loading the w83782d module.
+
+chip "w83627hf-*"
+    label   in0 "VCore1"
+    set     in0_min cpu0_vid*0.95
+    set     in0_max cpu0_vid*1.05
+    label   in1 "VCore2"
+    set     in1_min cpu0_vid*0.95
+    set     in1_max cpu0_vid*1.05
+    label   in2 "+3.3 V"
+    set     in2_min 3.3*0.95
+    set     in2_max 3.3*1.05
+    ignore  in3
+    label   in4 " +12 V"
+    compute in4 ((3.8/1)+1)*@ , @/((3.8/1)+1)
+    set     in4_max 12*0.90
+    set     in4_min 12*1.10
+    label   in5 " -12 V"
+    compute in5 (5.14*@)-14.91 , (@+14.91)/5.14
+    set     in5_max -12*0.90
+    set     in5_min -12*1.10
+    ignore  in6
+    ignore  in7
+    ignore  in8
+    ignore  vid
+    label   temp1 "VRM1 Temp"
+    label   temp2 "AGP Temp"
+    label   temp3 "DDR Temp"
+    label   fan1 "CPU1 Fan"
+    label   fan2 "CPU2 Fan"
+    ignore  fan3 
+#    set     temp1_type 2
+#    set     temp1_max 40
+#    set     temp1_max_hyst 37
+#    set     temp2_type 2
+#    set     temp2_max 52
+#    set     temp2_max_hyst 47
+#    set     temp3_type 2
+#    set     temp3_max 52
+#    set     temp3_max_hyst 47
+    set     beep_enable 0
diff --git a/configs/VIA/EPIA-M920.conf b/configs/VIA/EPIA-M920.conf
new file mode 100644
index 00000000..69f2846d
--- /dev/null
+++ b/configs/VIA/EPIA-M920.conf
@@ -0,0 +1,30 @@
+# Configuration file reportedly provided to users by VIA themselves.
+
+
+chip "f71869-*"
+
+    label in0 "+3.3V"
+    label in1 "+Vcore"
+    label in4 "Vdimm"
+    label in3 "+3.3V"
+    label in2 "+5V"
+    label in6 "+12V"
+    label in7 "3VSB"
+    label in8 "Vbat"
+    label fan1 "CPU Fan Speed"
+    label fan2 "System Fan Speed"
+    label temp1 "CPU Temperature"
+    label temp2 "System Temperature"
+
+    compute in0  @*2    , @/2
+    compute in2  @*2.5  , @/2.5
+    compute in3  @*2    , @/2
+    compute in4  @*1.47 , @/1.47
+    compute in6  @*11   , @/11
+    compute in7  @*2    , @/2
+    compute in8  @*2    , @/2
+
+    ignore in5
+    ignore fan3
+    ignore fan4
+    ignore temp3
diff --git a/configs/Zotac/H55-ITX.conf b/configs/Zotac/H55-ITX.conf
new file mode 100644
index 00000000..15a7bc7a
--- /dev/null
+++ b/configs/Zotac/H55-ITX.conf
@@ -0,0 +1,48 @@
+# Configuration contributed by Jean Delvare.
+
+
+chip "w83667hg-isa-0a10"
+
+   # Voltages
+
+   label  in0 "Vcore"
+   label  in1 "Vtt"
+   label  in2 "AVCC"
+   label  in3 "+3.3V"
+   label  in4 "PCH"
+   label  in5 "IGD"
+   label  in7 "3VSB"
+   label  in8 "Vbat"
+
+   set in1_min  1.1 * 0.95
+   set in1_max  1.1 * 1.05
+   set in2_min  3.3 * 0.90
+   set in2_max  3.3 * 1.10
+   set in3_min  3.3 * 0.90
+   set in3_max  3.3 * 1.10
+   set in4_min  1.1 * 0.95
+   set in4_max  1.1 * 1.05
+   set in7_min  3.3 * 0.90
+   set in7_max  3.3 * 1.10
+   set in8_min  3.0 * 0.90
+   set in8_max  3.0 * 1.10
+
+   # Fans
+
+   # I don't know which fan headers exist and which don't.
+   #ignore fan1
+   label  fan2 "CPU Fan"
+   #ignore fan3
+   #ignore fan4
+   #ignore fan5
+
+   set fan2_min  800
+
+   # Temperatures
+
+   label  temp1 "M/B Temp"
+   label  temp2 "CPU Temp"
+   ignore temp3
+
+   set temp1_max       55
+   set temp1_max_hyst  52
diff --git a/configs/Zotac/ZBox-HD-ID11.conf b/configs/Zotac/ZBox-HD-ID11.conf
new file mode 100644
index 00000000..66972836
--- /dev/null
+++ b/configs/Zotac/ZBox-HD-ID11.conf
@@ -0,0 +1,59 @@
+# Contributed by Piotr Maksymiuk.
+
+
+##/etc/sensors.d/zbox-hd-id-11
+
+chip "w83667hg-isa-0a10"
+
+   # Voltages
+
+   label  in0 "Vcore"
+   label  in1 "RAM"
+   label  in2 "AVCC"
+   label  in3 "+3.3V"
+   label  in4 "Chipset"
+   label  in5 "+1.5V"
+   label  in6 "3VSB"
+
+   set in0_min  1.1 * 0.90
+   set in0_max  1.1 * 1.10
+   set in1_min  1.9 * 0.90
+   set in1_max  1.9 * 1.10
+   set in2_min  3.3 * 0.90
+   set in2_max  3.3 * 1.10
+   set in3_min  3.3 * 0.90
+   set in3_max  3.3 * 1.10
+   set in4_min  1.1 * 0.90
+   set in4_max  1.1 * 1.10
+   set in5_min  1.5 * 0.90
+   set in5_max  1.5 * 1.10
+
+   # Fans
+
+   # Only fan2 is used in this barebone.
+   ignore fan1
+   label  fan2 "Case Fan"
+   ignore fan3
+   ignore fan4
+   ignore fan5
+
+   set fan2_min  800
+
+   # Temperatures
+
+   #unfortunately i'm not sure if temp3 is ram
+   label  temp1 "M/B Temp"
+   label  temp2 "CPU Temp"
+   label  temp3 "RAM Temp"
+
+   #this always returns a 0 reading
+   ignore cpu0_vid
+
+   set temp1_max       50
+   set temp1_max_hyst  40
+
+   set temp2_max       75
+   set temp2_max_hyst  60
+
+   set temp3_max       35
+   set temp3_max_hyst  30