diff --git a/CHANGES b/CHANGES
index 0240333d..248cb4fb 100644
--- a/CHANGES
+++ b/CHANGES
@@ -26,7 +26,8 @@ ask CVS about it:
   File doc/chips/via686a: Claim support for 686b.
   File sensors.conf.eg: Adjust as99127f in5 (-12V) and temp2 calculations;
                         Add lm87, adm9240, ds1780, lm81 templates;
-                        Enhance help comments in file
+                        Enhance help comments in file;
+                        Add Tyan S2510 dual-MTP008 example.
   File sensors.c: Add xxx_init() calls for drivers added to mkpatch in 2.5.5.
   Include file i2c-isa.h: No longer required, moved to i2c.h in i2c package
   Include file sensors.h: Most contents moved to i2c-proc.h in i2c package
@@ -40,6 +41,8 @@ ask CVS about it:
                  Save BIOS pin configuration of temps and fans
   Module sensors: Disabled, moved to i2c package as i2c-proc.c
   Module via686a: Allow force=9191,address (for A7V/K7V boards)
+  Module w83781d: Don't reinitialize as99127f chip; this may cause fan/temp
+                  reading changes
   Program mkpatch.pl: Fix adm9240 typos, add more chips to Configure.help
   Program sensord: Add -d (debug) and -p (pid-file) options
   Program sensors: Change reported version from 1.3 to the lm_sensors version;
diff --git a/doc/chips/mtp008 b/doc/chips/mtp008
index 1d09e002..f22a96e6 100644
--- a/doc/chips/mtp008
+++ b/doc/chips/mtp008
@@ -1,7 +1,7 @@
 Kernel driver `mtp008.o'
 =========================
 
-Status: Complete; Alpha.
+Status: Complete; Beta.
         This chip is quite configurable and many settings cannot
         be done through the driver. Hopefully the BIOS settings will
 	be correct for most motherboards.
@@ -39,6 +39,10 @@ AIN5 is hooked up to the -12V sensing circuit.
 Other Tyan motherboards (the 2510 Thunder and the Tiger 200) appear to
 have different configurations.
 
+For the 2510, which has two MTP008 chips, each with a different
+configuration, follow the instructions in the mtp008 section of
+etc/sensors.conf.eg to configure 'sensors' correctly.
+
 The PWM outputs are configurable but not via the driver.
 The Fan input types (2 wire or 3 wire) are configurable but
 not via the driver.
diff --git a/etc/sensors.conf.eg b/etc/sensors.conf.eg
index 30de6bb7..6985f745 100644
--- a/etc/sensors.conf.eg
+++ b/etc/sensors.conf.eg
@@ -688,8 +688,9 @@ chip "via686a-*"
 
 chip "mtp008-*"
     
-# The values below should be correct if you own a Tyan S1834D motherboard.  If
-# not, please contact us, so we can figure out better readings.
+# The values below should be correct if you own a Tyan S1834D motherboard.
+# If not, please contact us, so we can figure out better readings.
+# FOR TYAN S2510 SEE END OF THIS SECTION.
 
 # For positive voltages outside the 0..4.09V range (in2..in4), two resistors
 # are used, with the following formula (R1,R2: resistor values, Vs: read
@@ -713,9 +714,9 @@ chip "mtp008-*"
     label in5 "-12V"
     label in6 "Vtt"
 
-    label fan1 "CPUFAN1"
-    label fan2 "CPUFAN2"
-    label fan3 "CPUFAN3"
+    label fan1 "CPU1 Fan"
+    label fan2 "CPU2 Fan"
+    label fan3 "fan3"
 
     label temp1 "CPU1 Temp"
     label temp2 "CPU2 Temp"
@@ -732,6 +733,53 @@ chip "mtp008-*"
 #    set temp3_over 52	
 #    set temp3_hyst 47	
 
+# End of standard mtp008 configuration
+
+# TYAN S2510 INFORMATION
+# This motherboard has two mtp008's which are hooked up differently,
+# so they must be configured separately.
+# For this motherboard, COMMENT OUT the above mtp008 section and
+# UNCOMMENT the following two sections.
+#
+#chip mtp008-i2c-*-2c
+#    label in0 "VCore1"
+#    set in0_min 1.60
+#    set in0_max 1.80
+#    label in1 "+3.3V"
+#    label in2 "+12V"
+#    label in3 "Vcore2"
+#    set in3_min 1.60
+#    set in3_max 1.80
+#    ignore in4
+#    label in5 "-12V"
+#    label in6 "Vtt"
+#    label fan1 "CPU1 Fan"
+#    label fan2 "CPU2 Fan"
+#    label fan3 "fan3"
+#    label temp1 "CPU1 Temp"
+#    label temp2 "CPU2 Temp"
+#    ignore temp3
+#    compute in2 @ * 38 / 10,		@ * 10 / 38
+#    compute in5 (@ * 36 - 118.61) / 7,	(118.61 + 7 * @) / 36
+#
+#chip mtp008-i2c-*-2e
+#    ignore in0
+#    label in1 "+3.3V"
+#    ignore in2
+#    label in3 "+5V"
+#    set in3_min 4.50
+#    set in3_max 5.50
+#    ignore in4
+#    label in5 "+3.3V"
+#    ignore in6
+#    label fan1 "fan4"
+#    label fan2 "fan5"
+#    label fan3 "fan6"
+#    ignore temp1
+#    label temp2 "MB Temp"
+#    set temp2_over 52	
+#    set temp2_hyst 47	
+#    ignore temp3
 
 chip "adm1025-*"