diff --git a/doc/chips/thmc50 b/doc/chips/thmc50
new file mode 100644
index 00000000..572213e0
--- /dev/null
+++ b/doc/chips/thmc50
@@ -0,0 +1,92 @@
+Kernel driver `thmc50.o'
+=====================
+
+Status: Complete and some-what tested
+
+Supported chips: 
+  * Texas Instruments THMC50
+    Prefix: `thmc50'
+    Addresses scanned: I2C 0x2D - 0x2F (inclusive)
+    Datasheet: Publicly available at the Texas Instruments' website
+
+Authors: Frodo Looijaard <frodol@dds.nl> and 
+         Philip Edelbrock <phil@netroedge.com>
+
+
+Module Parameters
+-----------------
+
+* force: short array (min = 1, max = 48)
+  List of adapter,address pairs to boldly assume to be present
+* force_thmc50: short array (min = 1, max = 48)
+  List of adapter,address pairs which are unquestionably assumed to contain
+  a `thmc50' chip
+* ignore: short array (min = 1, max = 48)
+  List of adapter,address pairs not to scan
+* ignore_range: short array (min = 1, max = 48)
+  List of adapter,start-addr,end-addr triples not to scan
+* probe: short array (min = 1, max = 48)
+  List of adapter,address pairs to scan additionally
+* probe_range: short array (min = 1, max = 48)
+  List of adapter,start-addr,end-addr triples to scan additionally
+
+
+Description
+-----------
+
+The THMC50 implements: an internal temperature sensors, support for an
+external diode-type temperature sensor (compatible w/ the diode sensor inside
+many processors), and a controllable fan/analog_out DAC. For the temperature
+sensors, limits can be set through the appropriate Overtemperature Shutdown 
+register and Hysteris register. Each value can be set and read to half-degree 
+accuracy.  An alarm is issued (usually to a connected LM78) when the 
+temperature gets higher then the Overtemperature Shutdown value; it stays on 
+until the temperature falls below the Hysteris value. All temperatures are in 
+degrees Celcius, and are guaranteed within a range of -55 to +125 degrees.
+
+The THMC50 only updates its values each 1.5 seconds; reading it more often
+will do no harm, but will return 'old' values.
+
+The THMC50 is usually used in combination with LM78-like chips, to measure
+the temperature of the processor(s).
+
+
+Driver Features
+---------------
+
+These are the files which are provided by the driver (ro=read-only, 
+rw=read and writeable):
+
+temp -- 	Three fields: [temp-os,rw] [temp-hyst,rw] [temp,ro]
+remote_temp -- 	Three fields: [temp-os,rw] [temp-hyst,rw] [temp,ro]
+
+temp-os, temp-hyst, and temp are whole degree integers representing degrees
+celcius.
+
+analog_out --	One field: [output-value,rw]
+
+output-value is a number from 0 to 255 representing the voltage output
+provided by the DAC from 0 to 2.5, respectively.  Note: the max *current*
+supplied is actually quite low.  Some type of current amplification is needed
+in order to control a fan or other current demanding device (see the
+datasheet for more info).
+
+die_code --	One field: [die-code,ro]
+
+die-code is an integer representation of the die_code byte register. 
+According to the docs, the high nibble is the die version, and the lower
+nibble is the stepping.  (Don't ask me why or what this means! ;')
+
+inter --	One field: [interrupts,rw]
+
+interrupts is an integer representation of the interrupts byte.  See the data
+sheet for what bits mean what.
+
+inter_mask -- 	One field: [inter-mask,rw]
+
+inter-mask is an integer repressentation of the interrupt mask which is a
+determination of which conditions can cause the /INT pin on the chip to
+become asserted.
+
+
+