indication will always be valid; it won't be cleared forever by
reading the register. Do this by setting temp1_hyst to 127
and programming register 4C which sets it for temps 2 and 3.
Don't print hyst. value for temp1 in 'sensors' if == 127.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1407 7894878c-1315-0410-8ee3-d5d059ff63e0
Replace VID_FROM_REG() with vid_from_reg() in new sensors_vid.h.
Update library so it can be set in sensors.conf.
Add new documentation. Update mkpatch for new file.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1352 7894878c-1315-0410-8ee3-d5d059ff63e0
so that each temp. sensor for each chip can be printed with
the right number of digits. I tried to set each chip to
the right precision but there may still be some tweaking to do.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1161 7894878c-1315-0410-8ee3-d5d059ff63e0
The following patch does the following:
Fixed bug with not all alarms enabled.
Added ability to read battery voltage
Select temperature sensor type at module load time.
Added setting for Inside Technologies 786LCD board to example config file
I also fixed what looked like a typo in the existing it87 section where
in6_min/max was set twice and in7 was not set. As commented I think
the equation for the negative voltages are wrong but without that motherboard
I can't verify.
With the 786LCD board sensors-detect reports a lm78 which doesn't
exist and a sis5595 which may be part of the SIS630 chip but doesn't
perform the monitoring. The it8705F/SIS950 which is on the board is
reported as a misdetect. I didn't know enough about the various chips
to figure out how to get correct detections.
David Gesswein
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1146 7894878c-1315-0410-8ee3-d5d059ff63e0
on both platforms). LM87 support is very far along, and should work
for a majority of users, but some minor tweaks are still on the to-do list.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@963 7894878c-1315-0410-8ee3-d5d059ff63e0
Fahrenheit patch so that it will print either limit/hysteresis
or min/max. Add a flag to each call to select the right one.
Change temp output to be %3.1f. Some chips are 1 degree accuracy,
some are .5, the 686a is less. For now since it is a common
routine use one decimal point. In future maybe add another
parameter to the routine to specify accuracy.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@939 7894878c-1315-0410-8ee3-d5d059ff63e0
4 banks per memory chip. Add banks entry to libsensors and
use # of banks in calculation.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@839 7894878c-1315-0410-8ee3-d5d059ff63e0
can flag chassis intrusion detection to be ignored, etc. Updated
CHANGES to reflect this and updates to sensord.
-- merlin
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@837 7894878c-1315-0410-8ee3-d5d059ff63e0
This often-asked for, long-planned and somewhat-forgotten feature
makes it possible to tell libsensors-linked applications (like
the sensors program) that certain features should not be displayed.
This is very nice for things like unconnected temperature sensors
or fans.
Modifications to the library code, to the sensors program and to
the documentation and example sensors.conf file.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@676 7894878c-1315-0410-8ee3-d5d059ff63e0
Mark D. Studebaker