* The library can now read GL518SM revision 0x00 voltages (in the worst case,
it will read zeros if the module was not inserted with readall=1)
* The readall parameter is now documented through MODULE_PARM_DESC
* Note my remarks in the TODO file
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@403 7894878c-1315-0410-8ee3-d5d059ff63e0
Like the LM78 before, all chips now handle strange values written to /proc/...
with grace - that is, they convert them to the most sane value considering
the circumstances, instead of reacting with strange resulting values
(note that they were already crash-free).
I also removed a factor '2' in the computation of the fan speeds in the
gl518sm module. This is conforming with the sheet; if your fan gives two
'ticks' for each rotation, just modify sensors.conf.
I tried to introduce rounding and limit checking to the maxilife module.
The VID computation is not yet rounded - I need the real formula for that.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@382 7894878c-1315-0410-8ee3-d5d059ff63e0
gl518sm module
Besides the usual parameters, eeprom.o understands insmod parameter 'checksum'.
Set it to one (ie. 'modprobe eeprom checksum=1') to make it ignore any
chips which do not come through the checksum.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@371 7894878c-1315-0410-8ee3-d5d059ff63e0
Improved bounds checking for FAN_TO_REG in all files.
For lm78-compatible drivers, minimum speed is 2657 RPM when the
divisor is 2. Attempts to set lower than that now are set to 0.
Before was set to a random number.
Thanks Jeff Dairiki.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@330 7894878c-1315-0410-8ee3-d5d059ff63e0
Fan1 causes now alarm when rpm drops.
Fixed libsensors displaying incorrect temperature limits for rev 80.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@293 7894878c-1315-0410-8ee3-d5d059ff63e0
Code written by Ludovic Drolez (ldrolez@usa.net)
All voltages are now readable for the rev 00 but the read is blocked for 10
seconds because of the needed comparisons.
Currently voltages are readable in /proc only.
This functionality can be enabled at module-load with parameter readall:
insmod gl518 readall=1
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@289 7894878c-1315-0410-8ee3-d5d059ff63e0
* Better VDD internal computation, as described in the data sheet;
* Fixed the config file to reflect the above change;
* The library read the wrong file to get its gl518sm alarm data.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@150 7894878c-1315-0410-8ee3-d5d059ff63e0
* (module) VIN limits are now set to sane values (3V instead of 30V, which
caused nasty overflows)
* (module) VIN limits had min/max swapped in gl518_attach_adapter
* (lib) TEMP_HYST used the VID sysctl instead of the TEMP sysctl, leading
to bogus readings
* (sensors) print n/a for gl518 not available readings.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@145 7894878c-1315-0410-8ee3-d5d059ff63e0
This file consists of two numbers: the first is either 0 (global sound
alarm disable) or 1 (enable), the second is in the same encoding as the
'alarm' file and determines for which alarms the speaker will sound.
The new file was added to the module, the library and the sensors application.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@112 7894878c-1315-0410-8ee3-d5d059ff63e0
* Turned the i2c noise level down, by setting the debug_level in algo-bit.c
and i2c-core.c to 0 instead of 1. This should stop it from polluting
the dmesg output, as it does at this moment.
* Renamed gl518-r?0-* entries to gl518sm-r?0-*
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@82 7894878c-1315-0410-8ee3-d5d059ff63e0
Strangly enough, both these devices use a high byte, low byte order for
word-sized reads and writes. The SMBus documentation specifies the
reverse (low, high) order, though. If all devices use the high,low order,
we should change this in smbus.c.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@64 7894878c-1315-0410-8ee3-d5d059ff63e0
* Alarms may now work (sound signal disabled, though)
* Revision 0x80 should be recognized and handled correctly
* If fan unconnected, it should show 0 instead of -1 now
Note that this driver will not support GL520SM chips; that chip is different
enough that it deserves its own driver.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@61 7894878c-1315-0410-8ee3-d5d059ff63e0
To be done: support for GL518SM revision 0x80 and GL520SM
Kyösti, if you have some time soon, could you please test it?
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@56 7894878c-1315-0410-8ee3-d5d059ff63e0
Frodo Looijaard