The i801 driver is for the standard I2C bus on an i810 board.
This driver adds the support for the DDC and TV-out busses.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@729 7894878c-1315-0410-8ee3-d5d059ff63e0
Changes in sensors.c:
sensors_detect now skips addresses which are already taken. Even a
force parameter can not override this, as it could lead to major
problems.
For ISA addresses, the same is done; but the client drivers still need
a check if they claim more than one ISA address (as all of the current
ISA clients do).
Changes in chip drivers:
Removed the comment about needing address registration
Changes in i2cdetect.c:
Marks addresses which are already claimed
Changes in sensors-detect:
Warns when an address is already claimed, and skips it.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@667 7894878c-1315-0410-8ee3-d5d059ff63e0
* Removed several superfluous (struct i2c_client *) casts (they were left
from the time we had separate structs for smbus and isa)
* Removed the internal lists of registered clients
They have not been used for quite some time now, took memory space,
and limited the maximum number of clients that could be registered.
Also removed two small Makefile errors - I am happy I caught them before
the next release!
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@582 7894878c-1315-0410-8ee3-d5d059ff63e0
* i2c-isa simplified, by using the addr field in the client structure,
instead of a new field. This means we do not need `struct isa_*'
anymore
* All clients changed to reflect the new isa code. Many are much
simplified now.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@505 7894878c-1315-0410-8ee3-d5d059ff63e0
* The library can now read GL518SM revision 0x00 voltages (in the worst case,
it will read zeros if the module was not inserted with readall=1)
* The readall parameter is now documented through MODULE_PARM_DESC
* Note my remarks in the TODO file
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@403 7894878c-1315-0410-8ee3-d5d059ff63e0
Also a very slight formatting improvement for the module parameters
documentation script, and a typo from the LM78 documentation removed.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@393 7894878c-1315-0410-8ee3-d5d059ff63e0
* Removed unnecessary MOD_INC/DEC_USE_COUNT in host adapter drivers
(i2c-via bit-lp bit-velle)
You can now rmmod adapters even when they have registered clients.
Without this, you would have to detach the clients first. Only way of doing
this is to rmmod the client drivers, but the same drivers might be used to
access clients behind other hosts.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@347 7894878c-1315-0410-8ee3-d5d059ff63e0
It is untested as of yet; but it compiled without problem. Next step: add
support to the chip modules.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@324 7894878c-1315-0410-8ee3-d5d059ff63e0
Code written by Ludovic Drolez (ldrolez@usa.net)
All voltages are now readable for the rev 00 but the read is blocked for 10
seconds because of the needed comparisons.
Currently voltages are readable in /proc only.
This functionality can be enabled at module-load with parameter readall:
insmod gl518 readall=1
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@289 7894878c-1315-0410-8ee3-d5d059ff63e0
Mark D. Studebaker