The i801 driver is for the standard I2C bus on an i810 board.
This driver adds the support for the DDC and TV-out busses.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@729 7894878c-1315-0410-8ee3-d5d059ff63e0
Wasn't used by bt869 so wasn't found before.
i2cdump now works and sensors_detect will find ddc monitor.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@711 7894878c-1315-0410-8ee3-d5d059ff63e0
Initially, random values were put in the voltage registers. If iterate was
left at 0, these random values were put in /proc.
Solution: initialize voltage[0..2] with 0.
Frodo
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@709 7894878c-1315-0410-8ee3-d5d059ff63e0
Simultaneous DDC and I2C access may cause errors.
No support for multiple Voodoo3/Banshee chips, only first one
is handled.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@698 7894878c-1315-0410-8ee3-d5d059ff63e0
registers in I2C mode.
Instead of using bank 1 and 2, which was in violation of
the datasheets, use the separate I2C registers (usually
0x48 and 0x49). Register these addresses separately
using additional i2c_attach-client() calls.
Users will see new "subclient" registration messages
in the syslog.
/proc and libsensors interfaces are unchanged, i.e. the
chip still looks like a single device.
This should fix temp2 and temp3 for the as99127f, which
did not allow bank 1 and 2 accesses. Should not affect
operation for other chips as they worked before.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@686 7894878c-1315-0410-8ee3-d5d059ff63e0
Please test. Changes in voodoo3_setup:
* Use pci_find_device instead of traversing the list ourselves;
* Eliminate flag, testing v3_num is just as good;
* Elimiate result, it was not used anyway.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@684 7894878c-1315-0410-8ee3-d5d059ff63e0
Set DESTDIR if you want to install at some other place then where you
will run everything from.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@675 7894878c-1315-0410-8ee3-d5d059ff63e0
use lm75 driver for temp2 and temp3 until I fix w83781d driver.
LM75 detection fails on as99127f (and w83781d temp2).
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@670 7894878c-1315-0410-8ee3-d5d059ff63e0
Changes in sensors.c:
sensors_detect now skips addresses which are already taken. Even a
force parameter can not override this, as it could lead to major
problems.
For ISA addresses, the same is done; but the client drivers still need
a check if they claim more than one ISA address (as all of the current
ISA clients do).
Changes in chip drivers:
Removed the comment about needing address registration
Changes in i2cdetect.c:
Marks addresses which are already claimed
Changes in sensors-detect:
Warns when an address is already claimed, and skips it.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@667 7894878c-1315-0410-8ee3-d5d059ff63e0
Reasons varied from typos (_ instead of -) to static declarations that
should have been extern.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@646 7894878c-1315-0410-8ee3-d5d059ff63e0
<linux/version.h> was not included (it was automatically
included by <linux/module.h> when a module, but that is not good
enough of course...)
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@644 7894878c-1315-0410-8ee3-d5d059ff63e0
sensors-detect detection is now complete; I think nothing else needs
to be done in the tree?!? (except documentation of course)
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@643 7894878c-1315-0410-8ee3-d5d059ff63e0
Mark D. Studebaker