Set DESTDIR if you want to install at some other place then where you
will run everything from.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@675 7894878c-1315-0410-8ee3-d5d059ff63e0
use lm75 driver for temp2 and temp3 until I fix w83781d driver.
LM75 detection fails on as99127f (and w83781d temp2).
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@670 7894878c-1315-0410-8ee3-d5d059ff63e0
Changes in sensors.c:
sensors_detect now skips addresses which are already taken. Even a
force parameter can not override this, as it could lead to major
problems.
For ISA addresses, the same is done; but the client drivers still need
a check if they claim more than one ISA address (as all of the current
ISA clients do).
Changes in chip drivers:
Removed the comment about needing address registration
Changes in i2cdetect.c:
Marks addresses which are already claimed
Changes in sensors-detect:
Warns when an address is already claimed, and skips it.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@667 7894878c-1315-0410-8ee3-d5d059ff63e0
Reasons varied from typos (_ instead of -) to static declarations that
should have been extern.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@646 7894878c-1315-0410-8ee3-d5d059ff63e0
<linux/version.h> was not included (it was automatically
included by <linux/module.h> when a module, but that is not good
enough of course...)
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@644 7894878c-1315-0410-8ee3-d5d059ff63e0
sensors-detect detection is now complete; I think nothing else needs
to be done in the tree?!? (except documentation of course)
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@643 7894878c-1315-0410-8ee3-d5d059ff63e0
* Improved monitoring of /proc directories
Instead of doing:
proc_bus_i2c->fill_inode = &monitor_bus_i2c;
void monitor_bus_i2c(struct inode *inode, int fill)
{
if (fill)
MOD_INC_USE_COUNT;
else
MOD_DEC_USE_COUNT;
}
you can now simply set:
proc_bus_i2c->owner = THIS_MODULE;
and this is just as good!
* An old 2.3 problem seemingly never was resolved yet: instead of using
a *wait_queue directly, you have to use a wait_queue_head_t and
initialize it properly:
#if (LINUX_VERSION_CODE < 0x020301)
static struct wait_queue *pcf_wait = NULL;
#else
static wait_queue_head_t pcf_wait;
#endif
#if (LINUX_VERSION_CODE >= 0x020301)
init_waitqueue_head(&pcf_wait);
#endif
except for this, semantics remain the same (but using a plain
wait_queue_head_t instead of a pointer to a wait_queue)
* I had to change the semantics of sensors_register_entry slightly,
to make the monitoring of /proc/sys/dev/* files possible for kernels
2.3.27 and newer. It now takes an additional parameter, which you
can specify as THIS_MODULE.
* THIS_MODULE is only defined in kernels 2.3.13 and later; added
it to compat.h and the compatibility section of mkpatch.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@640 7894878c-1315-0410-8ee3-d5d059ff63e0
(1.75 to 1.30 Volts) as specified in Intel document
243773302.pdf. Lower voltages are coming!
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@617 7894878c-1315-0410-8ee3-d5d059ff63e0
* Removed several superfluous (struct i2c_client *) casts (they were left
from the time we had separate structs for smbus and isa)
* Removed the internal lists of registered clients
They have not been used for quite some time now, took memory space,
and limited the maximum number of clients that could be registered.
Also removed two small Makefile errors - I am happy I caught them before
the next release!
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@582 7894878c-1315-0410-8ee3-d5d059ff63e0
The Makefile now examine $(LINUX)/.config to see what modules need to be
compiled. It compiles only those modules which were either not configured
in at all, or were built as modules (ie. drivers which are built-in in the
kernel are not built, as they can not be overruled).
The above is still potentially dangerous, if we break the interface of
our modules. Still, it is much better than it was.
C
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@575 7894878c-1315-0410-8ee3-d5d059ff63e0
be working perfectly. Of course, some real-world users might find something
I didn't... BTW- I caught a minor bug which I thought was funny, and checked
lm75.c to see if it was there from the start... and it was! So, I managed to
catch a bug in lm75.c which might have resulted in bad temp_hyst readings
during that short period between setting new limits and the next valid update.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@564 7894878c-1315-0410-8ee3-d5d059ff63e0
Most important change: GL518SM-rev00 can't use kernel threads on 2.0 and
early 2.1 kernels
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@563 7894878c-1315-0410-8ee3-d5d059ff63e0
Frodo Looijaard