For lm78, 78-j, 79, w83781d, and as99127f, the chips have integral
inverters, so the compute lines are inverting.
Therefore the min register is really max and vice versa.
So the library was wrong, but sensors.conf.eg was wrong too,
so the chip got programmed correctly but 'sensors' printed
min and max backwards.
This was a different situation than for the previous fix to
sensors.conf.eg, where the chips were programmed wrong due
solely to sensors.conf.eg being incorrect.
In this fix we change the library and sensors.conf.eg.
The chip is still programmed right by 'sensors -s' (since
the library and sensors.conf changes cancel each other out)
but 'sensors' now prints correctly.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1305 7894878c-1315-0410-8ee3-d5d059ff63e0
These were set to NO_MAPPING so compute entries for
the fans would not affect the fan_mins.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1255 7894878c-1315-0410-8ee3-d5d059ff63e0
The following patch does the following:
Fixed bug with not all alarms enabled.
Added ability to read battery voltage
Select temperature sensor type at module load time.
Added setting for Inside Technologies 786LCD board to example config file
I also fixed what looked like a typo in the existing it87 section where
in6_min/max was set twice and in7 was not set. As commented I think
the equation for the negative voltages are wrong but without that motherboard
I can't verify.
With the 786LCD board sensors-detect reports a lm78 which doesn't
exist and a sis5595 which may be part of the SIS630 chip but doesn't
perform the monitoring. The it8705F/SIS950 which is on the board is
reported as a misdetect. I didn't know enough about the various chips
to figure out how to get correct detections.
David Gesswein
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1146 7894878c-1315-0410-8ee3-d5d059ff63e0
on both platforms). LM87 support is very far along, and should work
for a majority of users, but some minor tweaks are still on the to-do list.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@963 7894878c-1315-0410-8ee3-d5d059ff63e0
4 banks per memory chip. Add banks entry to libsensors and
use # of banks in calculation.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@839 7894878c-1315-0410-8ee3-d5d059ff63e0
* gl518sm document simplified for rev 0x00 & 0x80
* gl518sm & gl520sm libsensors interface updates
BTW: Revision is no longer part of the name, so old sensors.conf
will not work at all with gl518sm.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@511 7894878c-1315-0410-8ee3-d5d059ff63e0
* The library can now read GL518SM revision 0x00 voltages (in the worst case,
it will read zeros if the module was not inserted with readall=1)
* The readall parameter is now documented through MODULE_PARM_DESC
* Note my remarks in the TODO file
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@403 7894878c-1315-0410-8ee3-d5d059ff63e0
* Readings for the ADM9240 are now updated every 0.5 seconds; for the
DS1780, every 2.0 seconds.
* I still think it likely that voltage readings will be far-off in the
current implementation
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@401 7894878c-1315-0410-8ee3-d5d059ff63e0
Now prints out what kind of sensor it is.
Also separated alarms for temp2 and temp3 for 782d/783s (they are
a single bit for 781d).
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@400 7894878c-1315-0410-8ee3-d5d059ff63e0
The old documentation of Phil is still present at the bottom of the file.
Phil may decide to remove it.
In the driver, file 'status' is renamed to 'alarms' and masked to display
only the alarm bits. This fits more closely with other drivers, and the
remaining bit was not interesting anyway.
I fixed a problem that made insertion of the module impossible (I made a
typo when I introduced the insmod parameters) *** Someone else seems to
have changed this at almost the same moment?!? Now it is correct. ***
The MAX1617 and MAX1617A are now also supported by the library.
Once more, some slight formatting changes are made in the documentation
generators (some columns were made wider).
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@395 7894878c-1315-0410-8ee3-d5d059ff63e0
I've reviewed and applied the patch, but I would like some others to review
these commits too, to be safe.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@327 7894878c-1315-0410-8ee3-d5d059ff63e0
Fan1 causes now alarm when rpm drops.
Fixed libsensors displaying incorrect temperature limits for rev 80.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@293 7894878c-1315-0410-8ee3-d5d059ff63e0
I am trying to create a more-or-less standard documentation format for
doc/chips/* files. I am not quite satisfied with the lm75 and lm78 docs
yet, but it is starting to come. Basically, I want as much information
in it as possible, and to generate most of it automatically. But that is
harder than I though it would be.
Also, a small library bugfix (class problem) and a doc-features fix.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@210 7894878c-1315-0410-8ee3-d5d059ff63e0
I added two new make file 'includes': busses/Module.mk and chips/Module.mk
Frodo- You may want to review the makefile structure to make sure that
the system works as you intended.
Note: The docs still need to be updated to reflect the new file arrangement,
but at least it builds!
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@176 7894878c-1315-0410-8ee3-d5d059ff63e0
Mark D. Studebaker