4 banks per memory chip. Add banks entry to libsensors and
use # of banks in calculation.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@839 7894878c-1315-0410-8ee3-d5d059ff63e0
* gl518sm document simplified for rev 0x00 & 0x80
* gl518sm & gl520sm libsensors interface updates
BTW: Revision is no longer part of the name, so old sensors.conf
will not work at all with gl518sm.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@511 7894878c-1315-0410-8ee3-d5d059ff63e0
* The library can now read GL518SM revision 0x00 voltages (in the worst case,
it will read zeros if the module was not inserted with readall=1)
* The readall parameter is now documented through MODULE_PARM_DESC
* Note my remarks in the TODO file
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@403 7894878c-1315-0410-8ee3-d5d059ff63e0
* Readings for the ADM9240 are now updated every 0.5 seconds; for the
DS1780, every 2.0 seconds.
* I still think it likely that voltage readings will be far-off in the
current implementation
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@401 7894878c-1315-0410-8ee3-d5d059ff63e0
Now prints out what kind of sensor it is.
Also separated alarms for temp2 and temp3 for 782d/783s (they are
a single bit for 781d).
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@400 7894878c-1315-0410-8ee3-d5d059ff63e0
The old documentation of Phil is still present at the bottom of the file.
Phil may decide to remove it.
In the driver, file 'status' is renamed to 'alarms' and masked to display
only the alarm bits. This fits more closely with other drivers, and the
remaining bit was not interesting anyway.
I fixed a problem that made insertion of the module impossible (I made a
typo when I introduced the insmod parameters) *** Someone else seems to
have changed this at almost the same moment?!? Now it is correct. ***
The MAX1617 and MAX1617A are now also supported by the library.
Once more, some slight formatting changes are made in the documentation
generators (some columns were made wider).
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@395 7894878c-1315-0410-8ee3-d5d059ff63e0
I've reviewed and applied the patch, but I would like some others to review
these commits too, to be safe.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@327 7894878c-1315-0410-8ee3-d5d059ff63e0
output to ADM9240. Status/alarms values need to be implemented instead
of a raw output, but I'll do that too.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@173 7894878c-1315-0410-8ee3-d5d059ff63e0
This file consists of two numbers: the first is either 0 (global sound
alarm disable) or 1 (enable), the second is in the same encoding as the
'alarm' file and determines for which alarms the speaker will sound.
The new file was added to the module, the library and the sensors application.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@112 7894878c-1315-0410-8ee3-d5d059ff63e0
Mark D. Studebaker