* The library can now read GL518SM revision 0x00 voltages (in the worst case,
it will read zeros if the module was not inserted with readall=1)
* The readall parameter is now documented through MODULE_PARM_DESC
* Note my remarks in the TODO file
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@403 7894878c-1315-0410-8ee3-d5d059ff63e0
* Readings for the ADM9240 are now updated every 0.5 seconds; for the
DS1780, every 2.0 seconds.
* I still think it likely that voltage readings will be far-off in the
current implementation
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@401 7894878c-1315-0410-8ee3-d5d059ff63e0
it proves to be noxious. Added writes for rt table. Use at own risk.
Fixed 782d fan3 bug hopefully.
Added 16,32,64,128 fan_div values for 782d/783s.
Reformatted some > 80 col. lines.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@397 7894878c-1315-0410-8ee3-d5d059ff63e0
The old documentation of Phil is still present at the bottom of the file.
Phil may decide to remove it.
In the driver, file 'status' is renamed to 'alarms' and masked to display
only the alarm bits. This fits more closely with other drivers, and the
remaining bit was not interesting anyway.
I fixed a problem that made insertion of the module impossible (I made a
typo when I introduced the insmod parameters) *** Someone else seems to
have changed this at almost the same moment?!? Now it is correct. ***
The MAX1617 and MAX1617A are now also supported by the library.
Once more, some slight formatting changes are made in the documentation
generators (some columns were made wider).
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@395 7894878c-1315-0410-8ee3-d5d059ff63e0
Like the LM78 before, all chips now handle strange values written to /proc/...
with grace - that is, they convert them to the most sane value considering
the circumstances, instead of reacting with strange resulting values
(note that they were already crash-free).
I also removed a factor '2' in the computation of the fan speeds in the
gl518sm module. This is conforming with the sheet; if your fan gives two
'ticks' for each rotation, just modify sensors.conf.
I tried to introduce rounding and limit checking to the maxilife module.
The VID computation is not yet rounded - I need the real formula for that.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@382 7894878c-1315-0410-8ee3-d5d059ff63e0
Whatever you cat to /proc/..../lm78-*/*, the result will now always be
sensible. No more overflows resulting in weird values.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@381 7894878c-1315-0410-8ee3-d5d059ff63e0
* sis5595.c now understand insmod parameters
* sis5595.c now uses sis5595_ prefix instead of lm78_ prefix
* sis5595.c now supports the correct subset of the LM78 features
(it only knows about 4 voltages, 2 fans and no vid)
* added SIS5595 defines to sensors.h
* fixed a small problem in compat.h
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@379 7894878c-1315-0410-8ee3-d5d059ff63e0
die_code is only relevant for true ADM1021 chips; for the MAX1617, this
is simply undefined, and for the MAX1617A, it is the chip device ID
register. So the die_code file is only created for ADM1021 chips.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@376 7894878c-1315-0410-8ee3-d5d059ff63e0
This one was easy. A MAX1617 is just a MAX1617A with better detection.
Life is beautiful!
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@375 7894878c-1315-0410-8ee3-d5d059ff63e0
Detection is completely impossible, but sensors-detect now assumes with a
confidence of 1 (the lowest possible) that any chip in the LTC1710 address
range is a real LTC1710. Perhaps I should remove this again, as I don't
think this chip will be encountered 'in the wild' if your name is not Phil -
in which case you would have soldered it to your SMBus yourself, so you
should know what you are doing...
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@372 7894878c-1315-0410-8ee3-d5d059ff63e0
gl518sm module
Besides the usual parameters, eeprom.o understands insmod parameter 'checksum'.
Set it to one (ie. 'modprobe eeprom checksum=1') to make it ignore any
chips which do not come through the checksum.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@371 7894878c-1315-0410-8ee3-d5d059ff63e0
As always, I also synchronised the detection with sensors-detect. Its
detection is now much better; it used to scan at many addresses on which
these chips could never exist
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@367 7894878c-1315-0410-8ee3-d5d059ff63e0
is used but ignored (because the driver could not determine what
specific chip was there).
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@342 7894878c-1315-0410-8ee3-d5d059ff63e0
Also fixed a small lm78 problem and synchronised the detect script with
the Winbond detection.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@341 7894878c-1315-0410-8ee3-d5d059ff63e0
Also fixed a few nasty sensors.c bugs, and a minor LM78 one. If the new
parameters give trouble, please recompile sensors.c with DEBUG=1 and
examine the dmesg output!
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@338 7894878c-1315-0410-8ee3-d5d059ff63e0
Added RT table read to 781d but then #undef'ed it since it was just
all 1's. Changed max entries in sensor.c to 32 bytes to handle RT table.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@335 7894878c-1315-0410-8ee3-d5d059ff63e0
Improved bounds checking for FAN_TO_REG in all files.
For lm78-compatible drivers, minimum speed is 2657 RPM when the
divisor is 2. Attempts to set lower than that now are set to 0.
Before was set to a random number.
Thanks Jeff Dairiki.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@330 7894878c-1315-0410-8ee3-d5d059ff63e0
I've reviewed and applied the patch, but I would like some others to review
these commits too, to be safe.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@327 7894878c-1315-0410-8ee3-d5d059ff63e0
Supported insmod parameters:
ignore, ignore_range
probe, probe_range
force, force_lm78, force_lm78j, force_lm79
force* overrules ignore* overrules probe*
The *_range parameters need three elements for each specification:
bus,start_addr,end_addr
The address ranges are inclusive.
The other parameters need two elements for each specification:
bus,addr
In each case, '-1' stands for 'any I2C bus', and 9191 stands for
'the ISA bus' (Bonus question: who can figure out why I choose 9191?)
In each case, just append if you want several specification, for example:
insmod lm78 probe=9191,0x2a0,1,0x56
force_* does no detection, not even chip detection; it blindly assumes
you know what you are doing. plain force does the chip detection, but
nothing else; but it can still fail if the register read-out does not
match a chip type.
Detection is done in exactly the same way as sensors-detect, except that
only the range 0x20-0x2f is examined by default. This needs to be
synchronized somehow with the detect script. I would rather scan the whole
I2C address range, but with those clueless PIIX4 hangs when clock chips
are read, that would simply give too much trouble.
The detect script has slightly better ISA detection now, too.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@325 7894878c-1315-0410-8ee3-d5d059ff63e0
removed in1 and added in6 for 783s to keep compatibility
with 781d/782d. So 783s has no in1. sorry.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@313 7894878c-1315-0410-8ee3-d5d059ff63e0
Added limit defaults for in7/in8 and added separate
782d/783s limit defaults for in5/in6.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@304 7894878c-1315-0410-8ee3-d5d059ff63e0
Recognize chips, adjust /proc entries.
Added registers for Vbat/V5sb for 782d.
Did quick test that 781d isn't broken.
782d/783s untested, I'll send mail to the guy that volunteered.
No PWM fan support yet.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@297 7894878c-1315-0410-8ee3-d5d059ff63e0
Fan1 causes now alarm when rpm drops.
Fixed libsensors displaying incorrect temperature limits for rev 80.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@293 7894878c-1315-0410-8ee3-d5d059ff63e0
Code written by Ludovic Drolez (ldrolez@usa.net)
All voltages are now readable for the rev 00 but the read is blocked for 10
seconds because of the needed comparisons.
Currently voltages are readable in /proc only.
This functionality can be enabled at module-load with parameter readall:
insmod gl518 readall=1
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@289 7894878c-1315-0410-8ee3-d5d059ff63e0
device drivers. Specifically, I added these lines:
(in includes list)
#include "i2c-isa.h"
(Near beginning of *-attach-adapter function)
/* Make sure we aren't probing the ISA bus!! */
if (i2c_is_isa_adapter(adapter)) return 0;
This may be redundant is a couple of the files, but it shouldn't hurt.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@283 7894878c-1315-0410-8ee3-d5d059ff63e0
Frodo Looijaard