Michael Hufer <michael.hufer@freenet.de>
------------------------
> First, I added a new mod parameter "reset_it87" which controls whether
> or not the chip is reset on module load (modprobe it87 reset_it=1,
> default) or not(modprobe it87 reset_it87=0).
> Since this worked out quiet nicely I decided to go one step further
> and also add the chips manual and automatic temperature controlled fan
> speed features (PWM etc.).
>
> Finally I also updated the doc to document the new features.
>
> Attached is a diff against the current cvs version.
------------------------
Subject:
Re: fan speed for it87?? chips added
Date:
Fri, 26 Sep 2003 23:28:35 +0200
From:
Michael Hufer <michael.hufer@freenet.de>
To:
sensors@Stimpy.netroedge.com, Jean Delvare <khali@linux-fr.org>
On Friday 26 September 2003 22:40, Jean Delvare wrote:
> > I found and fixed the little problem I had with the original chip
> > initialization. I can now load the module with reset_it87=0 and
> > init=1 without messing up the settings of the power supply fan
> > from the BIOS. It was quite simple after all.
>
> I'm interested in details, can you tell us what it was?
Sure, it actually was something I introduced myself :-(. I initialized the
fan_ctl register with (read_value & 0x8f | 0x77) to enable the smart
guardian feature for all 3 fans. But the power supply fan does not support
pwm. It can only be operated in on/off mode, i.e. bit 0 must be clear. I
switched it back to the original (rv & 0x8f | 0x70 ) and everything is back
to working.
> > Do you want me to send the latest diff?
>
> Sure I want.
Here it comes.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@2033 7894878c-1315-0410-8ee3-d5d059ff63e0
- fix voltage scaling
- swap voltage limits
- use lower critical rather than upper hysteresis
for non-temperature sensors
- increase libsensors support to 20 voltage, 10 fan,
10 temperature sensors
Tickets 1406 and 1407.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@2017 7894878c-1315-0410-8ee3-d5d059ff63e0
From:
Kalev Soikonen <sokos@starman.ee>
Hi.
I am using lm_sensors in a slightly patched form.
The motherboard is Intel D845BGL, which features
SMSC LPC47M142 LPC Bus I/O controller.
If you look at the 47m10x and 47m14x datasheets,
you'll notice they have different Device ID's
(the former has 0x59, the latter 0x5F). As far
as the fan monitoring is concerned, they are
pretty much identical.
The 47M142 will be recognized with only some
trivial modifications to the code. I've attached
diffs for lm_sensors-2.7.0 and lm_sensors-2.8.0.
Best regards,
Kalev Soikonen
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1993 7894878c-1315-0410-8ee3-d5d059ff63e0
* Greg KH <greg@kroah.com> [2003-06-02 10:20:40 -0700]:
> On Sun, Jun 01, 2003 at 10:38:08AM -0400, Mark M. Hoffman wrote:
> > > This patch against 2.5.70 works for me vs. an SMBus adapter. It needs
> > re-testing against an ISA adapter since my particular chip is SMBus only.
>
> I've applied this and will send it off to Linus in a bit.
Thanks!
This patch fixes the various return values in the w83781d_detect()
error paths. It also cleans up some formatting here and there.
It should be applied on top of the previous one.
It works for me; same caveat as above w.r.t. ISA.
Regards,
--
Mark M. Hoffman
mhoffman@lightlink.com
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1990 7894878c-1315-0410-8ee3-d5d059ff63e0
Mainly targetted (and tested) with the 6651, but should work with
the MAX6550.
See doc/chips/max6650 for notes, bugs, assumptions, etc.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1987 7894878c-1315-0410-8ee3-d5d059ff63e0
(mmh) o remove devinitdata marking from i2c-nforce2.c as it's wrong
(mmh) o minor cleanups to the i2c-nforce2 driver
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1938 7894878c-1315-0410-8ee3-d5d059ff63e0
Add half a dozen new features.
Add checksum parameter (same as for the eeprom module)
Fix monitor limits
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1934 7894878c-1315-0410-8ee3-d5d059ff63e0
Update header comments, copyright and authors
Add support for Philips NE1619
Simplify the driver a lot (unified voltages, unified
temperatures and much more)
Fix default voltage limits
Change default temperature limits
Remove the adm1025_read_value and adm1025_write_value
wrappers (direct calls instead)
Swap remote and local temperatures to match the internal
registers order (make the code unification possible)
Export remote diode fault through alarms
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1919 7894878c-1315-0410-8ee3-d5d059ff63e0
SMBus pci device only - instead of also claiming the south bridge.
Although no problems had been reported with the previous detection
strategy, this change avoids the class of problems mentioned here:
http://archives.andrew.net.au/lm-sensors/msg03193.html
As a side benefit, it now looks much more like its sibling in 2.5.7x.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1893 7894878c-1315-0410-8ee3-d5d059ff63e0
Jean Delvare