# # pwmconfig v0.5 # Tests the pwm outputs of sensors and configures fancontrol # # Warning!!! This program will stop your fans, one at a time, # for approximately 3 seconds each!!! # This may cause your processor temperature to rise!!! # Verify that all fans are running at normal speed after this # program has exited!!! # # Copyright 2003 The lm_sensors project # # This program is free software; you can redistribute it and/or modify # it under the terms of the GNU General Public License as published by # the Free Software Foundation; either version 2 of the License, or # (at your option) any later version. # # This program is distributed in the hope that it will be useful, # but WITHOUT ANY WARRANTY; without even the implied warranty of # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the # GNU General Public License for more details. # # You should have received a copy of the GNU General Public License # along with this program; if not, write to the Free Software # Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. # # echo 'This program will search your sensors for pulse width modulation (pwm)' echo 'controls, and test each one to see if it controls a fan on' echo 'your motherboard. Note that many motherboards do not have pwm' echo 'circuitry installed, even if your sensor chip supports pwm.' echo echo 'We will attempt to briefly stop each fan using the pwm controls.' echo 'The program will attempt to restore each fan to full speed' echo 'after testing. However, it is ** very important ** that you' echo 'physically verify that the fans have been to full speed' echo 'after the program has completed.' echo DELAY=5 # 3 seconds delay is too short for large fans, thus I increased it to 5 DIR=/proc/sys/dev/sensors if [ ! -d $DIR ] then echo $0: 'No sensors found! (modprobe sensor modules?)' exit 1 fi cd $DIR DRIVERS=`echo *-*` if [ "*-*" = "$DRIVERS" ] then echo $0: 'No sensors found! (modprobe sensor modules?)' exit 1 fi PWM=`echo */pwm*` if [ "*/pwm*" = "$PWM" ] then echo $0: 'There are no pwm-capable sensor modules installed' exit 1 fi FAN=`echo */fan[1-9]` if [ "*/fan[1-9]" = "$FAN" ] then echo $0: 'There are no fan-capable sensor modules installed' exit 1 fi echo 'Found the following PWM controls:' for i in $PWM do echo " $i" if [ -w $i ] then echo 255 0 > $i else NOTROOT=1 fi done echo echo 'Found the following fan sensors:' for i in $FAN do S=`cat $i | cut -d' ' -f2` if [ "$S" = "0" -o "$S" = "-1" ] then echo " $i current speed: 0 ... skipping!" else echo " $i current speed: $S RPM" if [ "$GOODFAN" = "" ] then GOODFAN=$i SPEEDS=$S else GOODFAN="$GOODFAN $i" SPEEDS="$SPEEDS $S" fi fi done echo if [ "$GOODFAN" = "" ] then echo 'There are no working fan sensors, all readings are 0.' echo 'Make sure you have a 3-wire fan connected.' echo 'You may also need to increase the fan divisors.' echo 'See doc/fan-divisors for more information.' exit 1 fi if [ "$NOTROOT" = "1" ] then echo 'As you are not root, we cannot write the PWM settings.' echo 'Please run as root to continue.' exit 1 fi echo 'Warning!!! This program will stop your fans, one at a time,' echo "for approximately $DELAY seconds each!!!" echo 'This may cause your processor temperature to rise!!!' echo 'If you do not want to do this hit control-C now!!!' echo -n 'Hit return to continue: ' read X echo PLOTTER=gnuplot STEP=15 PDELAY=2 function pwmdetail() { P=$1 F=$2 PLOT= type gnuplot > /dev/null 2>&1 if [ $? -eq 0 ] then echo -n " Would you like to generate a graphical plot using $PLOTTER (y) ? " read X if [ "$X" = "y" -o "$X" = "Y" -o "$X" = "" ] then PLOT=y fi fi if [ "$PLOT" = "y" ] then TMP1=/usr/tmp/pwmtest$$.1 TMP2=/usr/tmp/pwmtest$$.2 echo "set xlabel \"PWM: $P\"" > $TMP1 echo "set ylabel \"FAN: $F (RPM)\"" >> $TMP1 echo 'set nokey' >> $TMP1 echo 'set xrange [0:255]' >> $TMP1 echo "plot \"$TMP2\" with lines" >> $TMP1 echo 'pause -1 " Hit return to continue..."' >> $TMP1 > $TMP2 fi let pwm=255 while [ $pwm -ge 0 ] do echo $pwm 1 > $P S=`cat $F | cut -d' ' -f2` echo " PWM $pwm FAN $S" if [ "$PLOT" = "y" ] then echo "$pwm $S" >> $TMP2 fi if [ "$S" = "0" -o "S" = "-1" ] then echo 255 0 > $P echo " Fan Stopped at PWM = $pwm" if [ $pwm -eq 255 ] then echo " This fan appears to stop when the PWM is enabled;" echo " perhaps the fan input shares a pin with the PWM output" echo " on the sensor chip." rm -f $TMP1 $TMP2 echo return 0 fi break fi let pwm=$pwm-$STEP sleep $PDELAY if [ $? -ne 0 ] then echo 255 0 > $P echo '^C received, aborting...' rm -f $TMP1 $TMP2 exit 1 fi done echo 255 0 > $P if [ "$PLOT" = "y" ] then $PLOTTER $TMP1 rm -f $TMP1 $TMP2 fi echo } for i in $PWM do echo Testing pwm control $i ... echo 0 1 > $i sleep $DELAY if [ $? -ne 0 ] then echo 255 0 > $i echo '^C received, restoring PWM and aborting...' exit 1 fi let pwmactivecount=0 let count=1 for j in $GOODFAN do OS=`echo $SPEEDS | cut -d' ' -f$count` S=`cat $j | cut -d' ' -f2` echo " $j ... speed was $OS now $S" echo 255 0 > $i let threshold=2*$OS/3 if [ $S -lt $threshold ] then echo " It appears that fan $j" echo " is controlled by pwm $i" # # a PWM can control more than one fan.... # if [ $pwmactivecount -eq 0 ] then let pwmactivecount=1 pwmactive="$i ${pwmactive}" fi sleep $DELAY if [ $? -ne 0 ] then echo '^C received, aborting...' exit 1 fi S=`cat $j | cut -d' ' -f2` if [ $S -lt $threshold ] then echo " Fan $j has not returned to speed, please investigate!" else echo -n " Would you like to generate a detailed correlation (y) ? " read X if [ "$X" = "y" -o "$X" = "Y" -o "$X" = "" ] then pwmdetail $i $j fi fi else echo " no correlation" fi let count=count+1 done echo if [ "$pwmactivecount" = "0" ] then echo "No correlations were detected, there is either no fan connected to the output of $i, or the connected fan has no rpm-signal connected to one of the tested fan sensors. (Note: not all motherboards have the pwm outputs connected to the fan connectors, check out the hardware database on http://www.almico.com/forumindex.php)" echo echo -n " Did you see/hear a fan stopping during the above test (y)?" read X if [ "$X" = "y" -o "$X" = "Y" -o "$X" = "" ] then pwmactive="$i ${pwmactive}" fi fi done echo 'Testing is complete.' echo 'Please verify that all fans have returned to their normal speed.' echo echo 'The fancontrol script can automatically respond to temperature changes' echo 'of your system by changing fanspeeds. Do you want to set up its' echo 'configuration file now? (y)' read X if [ "$X" = "n" -o "$X" = "N" ] then exit fi TEMPS=`echo */temp[1-9]` if [ "*/temp[1-9]" = "$TEMPS" ] then echo $0: 'There are no temperature-capable sensor modules installed' exit 1 fi function AskPath { echo 'What should be the path to your fancontrol config file? (/etc/fancontrol)' read X if [ "$X" = "y" -o "$X" = "Y" -o "$X" = "" ] then X=/etc/fancontrol fi if [ -f $X ] then FCCONFIG=$X else echo "$X does not exist, shall I create it now? (y)" read Y if [ "$Y" = "y" -o "$Y" = "Y" -o "$Y" = "" ] then touch $X chmod 0660 $X chown root.root $X FCCONFIG=$X else AskPath fi fi } AskPath function LoadConfig { echo "Loading configuration from $1 ..." INTERVAL=`egrep '^INTERVAL=.*$' $1 | sed -e 's/INTERVAL=//g'` FCTEMPS=`egrep '^FCTEMPS=.*$' $1 | sed -e 's/FCTEMPS=//g'` MINTEMP=`egrep '^MINTEMP=.*$' $1 | sed -e 's/MINTEMP=//g'` MAXTEMP=`egrep '^MAXTEMP=.*$' $1 | sed -e 's/MAXTEMP=//g'` MINSTART=`egrep '^MINSTART=.*$' $1 | sed -e 's/MINSTART=//g'` MINSTOP=`egrep '^MINSTOP=.*$' $1 | sed -e 's/MINSTOP=//g'` } LoadConfig $FCCONFIG function TestMinStart { echo echo 'Now we increase the PWM value in 10-unit-steps. Let the fan stop completely, then press return until the fan starts spinning, we will use this value +20 to be safe.' let fanok=0 let fanval=0 until [ "$fanok" = "1" ] do let fanval=fanval+10 echo -n "Setting $pwms to $fanval..." echo $fanval > $pwms read FANTEST if [ "$FANTEST" = "y" -o "$FANTEST" = "Y" ] ; then let fanok=1 ; fi done let fanval=fanval+20 if (( $fanval > 240 )) ; then let fanval=255 ; fi echo "OK, using $fanval" echo 255 > $pwms } function TestMinStop { echo echo 'Now we decrease the PWM value in 10-unit-steps, Let the fan has reach full speed, then press return until the fan stops spinning, we will use this value +20 as the minimum speed.' let fanok=0 let fanval=255 until [ "$fanok" = "1" ] do let fanval=fanval-10 if (( $fanval < 0 )) ; then fanval=0 ; fi echo -n "Setting $pwms to $fanval..." echo $fanval > $pwms read FANTEST if [ "$FANTEST" = "y" -o "$FANTEST" = "Y" ] ; then let fanok=1 ; fi done let fanval=fanval+20 if (( $fanval > 255 )) ; then let fanval=255 ; fi echo "OK, using $fanval" echo 255 > $pwms } function SaveConfig { echo echo "Saving configuration to $FCCONFIG..." egrep -v '(INTERVAL|FCTEMPS|MAXTEMP|MINTEMP|MINSTART|MINSTOP)' /etc/fancontrol >/tmp/fancontrol echo -e "INTERVAL=$INTERVAL\nFCTEMPS=$FCTEMPS\nMINTEMP=$MINTEMP\nMAXTEMP=$MAXTEMP\nMINSTART=$MINSTART\nMINSTOP=$MINSTOP" >>/tmp/fancontrol mv /tmp/fancontrol /etc/fancontrol #check if file was written correctly echo 'Configuration saved' } #function LoadConfig { #} INTERVAL=10 #the section below has a high potential for usability improvements echo echo 'Select fan output to configure:' select pwms in $pwmactive "Change INTERVAL" "Just quit" "Save and quit" "Show configuration"; do case $pwms in "Change INTERVAL") echo echo "Enter the interval at which fancontrol should update PWM values (in s):" read INTERVAL ;; #check user input here "Just quit") exit ;; "Save and quit") SaveConfig exit ;; "Show configuration") echo echo "Common Settings:" echo "INTERVAL=$INTERVAL" for pwmo in $pwmactive do echo echo "Settings of ${pwmo}:" echo " Depends on `echo $FCTEMPS |sed -e 's/ /\n/g' |egrep \"${pwmo}\" |sed -e 's/.*=//g'`" echo " MINTEMP=`echo $MINTEMP |sed -e \"s/ /\n/g\" |egrep \"${pwmo}\" |sed -e \"s/.*=//g\"`" echo " MAXTEMP=`echo $MAXTEMP |sed -e \"s/ /\n/g\" |egrep \"${pwmo}\" |sed -e \"s/.*=//g\"`" echo " MINSTART=`echo $MINSTART |sed -e \"s/ /\n/g\" |egrep \"${pwmo}\" |sed -e \"s/.*=//g\"`" echo " MINSTOP=`echo $MINSTOP |sed -e \"s/ /\n/g\" |egrep \"${pwmo}\" |sed -e \"s/.*=//g\"`" done echo ;; "`echo ${pwmactive} |sed -e \"s/ /\n/g\" | egrep \"${pwms}\"`" ) pwmsed=`echo ${pwms} | sed -e 's/\//\\\\\//g'` #escape / for sed echo echo "Select a temperature sensor as source for ${pwms}:" select tempss in $TEMPS "None (Do not affect this PWM output)"; do if [ "$tempss" = "None (Do not affect this PWM output)" ] then break; else if [ "$FCTEMPS" = "" ] then FCTEMPS="${pwms}=>${tempss}" else FCTEMPS="`echo $FCTEMPS | sed -e "s/${pwmsed}[^ ]* *//g\"` ${pwms}=${tempss}" fi fi echo echo 'Enter the minimum temperature at which the fan should be switched off:' read XMT if [ "$MINTEMP" = "" ] then MINTEMP="${pwms}=>${XMT}" else MINTEMP="`echo $MINTEMP | sed -e \"s/${pwmsed}[^ ]* *//g\"` ${pwms}=${XMT}" fi echo echo 'Enter the maximum temperature at which the fan should be switched to full speed:' read XMT if [ "$MAXTEMP" = "" ] then MAXTEMP="${pwms}=>${XMT}" else MAXTEMP="`echo $MAXTEMP | sed -e \"s/${pwmsed}[^ ]* *//g\"` ${pwms}=${XMT}" fi echo echo 'Enter the minimum PWM value at which the fan STARTS spinning (press return to test):' read XMV if [ "$XMV" = "" ] then TestMinStart XMV=$fanval fi if [ "$MINSTART" = "" ] then MINSTART="${pwms}=>${XMV}" else MINSTART="`echo $MINSTART | sed -e \"s/${pwmsed}[^ ]* *//g\"` ${pwms}=${XMV}" fi echo echo 'Enter the minimum PWM value at which the fan STOPS spinning (press return to test):' read XMV if [ "$XMV" = "" ] then TestMinStop XMV=$fanval fi if [ "$MINSTOP" = "" ] then MINSTOP="${pwms}=>${XMV}" else MINSTOP="`echo $MINSTOP | sed -e \"s/${pwmsed}[^ ]* *//g\"` ${pwms}=${XMV}" fi break; done ;; *) echo "No such option, press RETURN to show menu" ;; esac done