# Converted by sensors-conf-convert on Mon Jun 24 22:08:41 2019 # ASRock X370 taichi # 2018, contributed by bowman # # dmi: board_name: X370 Taichi # dmi: board_vendor: ASRock # dmi: bios_version: P5.10 # cpu: AMD Ryzen 7 1800X Eight-Core Processor chip "k10temp-pci-00c3" label temp1 "CPU Core Temp" label temp2 "CPU TCtrl Temp" chip "iwlwifi-virtual-0" label temp1 "Wifi Radio Temp" chip "nct6779-isa-*" # Fans label fan1 "Chassis Fan 3 Speed" label fan2 "CPU Fan 1 Speed" label fan3 "CPU Fan 2 Speed" label fan4 "Chassis Fan 1 Speed" label fan5 "Chassis Fan 2 Speed" # Temperatures label temp1 "Motherboard" label temp2 "CPU MB" label temp3 "Auxillary" label temp4 "VRM" label temp5 "AUXTIN2" # temp6 is almost always at -25. Not certain what to do about this. label temp6 "CPU (PECI)" # temp7 (CPU tCTL) A Thermal BIAS value generated by CPU # it includes an offset it is usedto drive mainboard Fans to higher speeds. # temp7 value is rounded off to the nearest ~1C only reported if # "Use Tctrl" has been selected in UEFI as the fan control sensor. # It will likely be offset by 20/10C on Ryzen X series CPU's label temp7 "CPU tCTL" # Voltages # VCore is different to VDDCR_CPU # VCore is a voltage measured somewhere by the Firmware. # (Readings may appear low at times (0.54V) and fluctuate - this is normal) label in0 "VCore" label in1 "VPPM" #scalar label in2 "AVCC" label in3 "3VCC" label in4 "+12V" #scalar label in5 "VDDCR_SOC" #(Data Fabric) label in6 "DRAM (VDDIO)" label in7 "3VSB" label in8 "VBat" ignore in9 #Unused input that is always at 0. label in10 "Mem_VTT" #(1/2 of VDDIO) label in11 "Chipset 1.05V" label in12 "+5V" label in13 "VDDP" label in14 "1.8V+" # CPU VCore limits set according to overclockers testing and AMD Max Safe # voltage recommendations. # Keep in mind Ryzen CPU's may boost to higher voltages for short times. # This is entirely dependant on individual chip binning. # If your chip indicates 1.55V continuously the sensors may not be treated # correctly by your mainboard or you have buggy firmware. # In that case It might be actually 1.55V which would correlates with # high heat, or it may be just a bad readout. # Note: sustained 1.45 is also not safe. # I am not sure about the low load voltage drops, they are normal # (commonly occuring on many boards) and thus likely a measurement or # sensor anomaly. # There is a more accurate on-die voltage sensor with ryzen. # but the documentation is covered by NDA. k10-temp would need to be # adapated to read voltages in addition to temperatures like HWInfo64 on # Windows already does. set in0_min 0.40 #Possibly inaccurate at low voltages. set in0_max 1.45 # VPPM Voltage 5% set in1_min 2.50 * 0.95 set in1_max 2.50 * 1.05 # Most PSU voltages set according to ATX v2.2 spec +/- 5% on the following: # +3.3VDC ± 5% +3.135 VDC +3.465 VDC # +5VDC ± 5% +4.750 VDC +5.250 VDC # +5VSB ± 5% +4.750 VDC +5.250 VDC # -5VDC ± 10% -4.500 VDC -5.500 VDC # +12VDC ± 5% +11.400 VDC +12.600 VDC # -12VDC ± 10% -10.800 VDC -13.200 VDC # +12VDC set in4_min 12 * 0.95 set in4_max 12 * 1.05 # VDDCR_SOC (fabric & peripheral) voltage levels # This can vary largely from board to board and among CPU's set in5_min 0.80 set in5_max 1.20 # DDR 4 RAM Tolerances VDDIO (1.2V DDR4 JEDEC standard) set in6_min 1.10 #Underclocking set in6_max 1.50 #Intel XMP2.0 recommended max safe voltage # Memory VTT Voltages (this should correspond to approximately VDDIO/2) set in10_min 1.20 * 0.5 #Stock Voltage set in10_max 1.50 * 0.5 #Overclocked XMP Voltage # Uncertain tolerances for the Ryzen Chipset set in11_min 0.90 #Undervolting set in11_max 1.20 #Overvolting set in12_min 5 * 0.95 set in12_max 5 * 1.05 # CLDO_VDDP Magic - helps to set to 1.0V when RAM overclocking or on XMP set in13_min 0.95 * 0.96 set in13_max 0.95 * 1.13 # PLL (Phase locked loop) voltage on the CPU. set in14_min 1.8 * 0.98 set in14_max 1.8 * 1.02 # Compute Inputs # The nct6779D uses a 2.048V input range, all inputs above that are scaled # using a voltage divider. # Below inputs utilize an integrated voltage divider: # ADC, AVCC, VBAT, 3VSB and 3VCC # # values as per nuvoton nct6779D datasheet # Section 8.5 Analog Inputs (Page 54,55) # # Vs R1,Rin R2,Rf Vin # in4 +12.0 56 10 ~+1.84 # in12 +5.0 20 10 ~+1.67 # compute in0 @*2, @/2 compute in1 @*2, @/2 compute in4 ((56/10)+1)*@, @/((56/10)+1) compute in12 ((20/10)+1)*@, @/((20/10)+1) # Potential things to filter # These inputs are unused unless you have a case intrusion switch connected. #ignore intrusion0 #ignore intrusion1