# Configuration file contributed by Lee Marriott.


# libsensors configuration file
# -----------------------------
#
# This is a first attempt at a custom configuration file for the Biostar N68S+.
# This custom configuration file should be copied to /etc/sensors.d/Biostar-N68S+.conf.
#
# Custom configuration files for some specific mainboards can be found at
# https://github.com/lm-sensors/lm-sensors/tree/master/configs

# READ THE MAN PAGE DOCUMENTATION OF 'sensors.conf' FOR MORE
# COMPLETE INFORMATION. ie:

# man sensors.conf

# Regarding the Biostar N68S+ motherboard: This motherboard supports
# both manual overclocking by individual settings and preconfigured
# overclocking using predefined sets of overclock settings.

chip "it8716-*"

# All labels set to match Biostar N68S+ BIOS displayed labels. See
# the 'PC Health' screen in the BIOS.

# Voltage settings

    label in0 "  Vcore"
    label in1 "Chipset"
    ignore in2           # +3.3 V not in BIOS
    label in3 "   +5 V"  # VCC
    label in4 "  +12 V"
    label in5 "    DDR"
    label in6 "     HT"
    label in7 "   5VSB"
    label in8 "   Vbat"

    compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
    compute in4 ((30/10)+1)*@ , @/((30/10)+1)
    compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)

    ignore cpu0_vid

# Other than +3.3, +5.0 and +12.0 voltages (here set plus/minus 10%), the
# indicated min/max voltages are a guess based on present measurements
# and similar to those on my Asus m/b.
# 

    set in0_min   0.80
    set in0_max   1.80
    set in1_min   1.1
    set in1_max   1.76
#    set in2_min   3.3 * 0.90
#    set in2_max   3.3 * 1.10
    set in3_min   5.0 * 0.90
    set in3_max   5.0 * 1.10
    set in4_min  12.0 * 0.90
    set in4_max  12.0 * 1.10
    set in5_min   1.60
    set in5_max   2.20
    set in6_min   0.95
    set in6_max   1.4
    set in7_min   5.0 * 0.90
    set in7_max   5.0 * 1.10

# Fan settings

    label fan1 "CPU fan"
    label fan2 "Sys1fan"
    label fan3 " NB fan"

    # Ignore fans you don't have
   ignore fan3

#
# The Biostart N68S+ is based upon the nVidia GeForce 7025/nForce 630a
# chipset and comes with active (fan based) cooling.

# Biostar N68S+ can allow 0 rpm for the CPU fan when in SMART
# fan control mode. Set min speeds as applicable for your system.

#    set fan1_min 1000
    set fan1_min 0
    set fan2_min 1000
#    set fan3_min 5600

# Temperature sensor settings

    label temp1 "CPU Tmp"
    label temp2 "M/B Tmp"
    label temp3 "NB     "

# BioStar N68S+ BIOS doesn't use 'temp2' and 'temp3'.

    ignore temp2
    ignore temp3

# Only set tempX_type if you have PC Health [disabled]
# in your BIOS???? Generally, the kernel {lmsensors} will
# correctly detect individual temperature sensor type and
# set values accordingly.
# 2 = thermistor; 3 = thermal diode; 0 = unused

#    set temp1_type 2
#    set temp2_type 2
#    set temp3_type 3

# Set your temparature max values. Warning: If your values here
# are set higher than the values set in your BIOS, then you may
# shutdown at a lower temperature than you think. It's probably
# best to assume that shutdown will occur at the lowest setting
# whenever the value here and the BIOS are different.

   set temp1_max  50
   set temp1_min  10
#   set temp2_max  50
#   set temp2_min  10

# The other possibility is that a value set here will always
# override the BIOS. You may or may not want that behavior.