# /etc/sensors.d/X8DTN
# settings for the supermicro X8DTN
# originally written by Gary E. Miller <gem@rellim.com>
# use at your own risk !
# Date: 25 May 2012

# Here's the info as supplied by Supermicro:

#
# Bus Type = ISAIO/SMBus
# One W83795AG
# 
# Windbond W83795AG, Slave Address=0x2f (0x5E in 8-Bit format)
# =============================================================
# Fan1 Fan Speed, Offset 0x2e		RPM = 84375/Data
# Fan2 Fan Speed, Offset 0x2f		RPM = 84375/Data
# Fan3 Fan Speed, Offset 0x30		RPM = 84375/Data
# Fan4 Fan Speed, Offset 0x31		RPM = 84375/Data
# Fan5 Fan Speed, Offset 0x32		RPM = 84375/Data
# Fan6 Fan Speed, Offset 0x33		RPM = 84375/Data
# Fan7 Fan Speed, Offset 0x34		RPM = 84375/Data
# Fan8 Fan Speed, Offset 0x35		RPM = 84375/Data
# CPU1 Voltage, Offset 0x10		Voltage = Data* 0.008
# CPU2 Voltage, Offset 0x11		Voltage = Data* 0.008
# +1.5V Voltage, Offset 0x12		Voltage = Data* 0.008
# +5V Voltage, Offset 0x13		Voltage = Data* 0.008 * (40/10)
# +12V Voltage, Offset 0x14		Voltage = Data* 0.008/ (10./66.2)
# +5VSB Voltage, Offset 0x15		Voltage = Data* 0.008 * (40/10)
# +3.3V Voltage, Offset 0x1c		Voltage = Data* 0.024
# +3.3VSB Voltage, Offset 0x1d		Voltage = Data* 0.024
# Battery Voltage, Offset 0x1e		Voltage = Data* 0.024
# CPU1 Temperature, Offset 0x27		Temperature = Data
# CPU2 Temperature, Offset 0x26		Temperature = Data
# System Temperature, Offset 0x1f		Temperature = Data
# Chassis Intrusion, Bank 0, Offset 0x46, BitMask 0x40	1 = Bad, 0 = Good
#		 (Clear Bit: Bank 0, Offset 0x4d, BitMask 0x80)
# 
# 
# Power Supply Failure, GP11(From W83627HF)		1 = Good, 0 = Bad
 
chip "w83627hf-isa-0a00"
    # I'm not sure which is GP11, so I turned off everything.
    ignore in0
    ignore in1
    ignore in2
    ignore in3
    ignore in4
    ignore in5
    ignore in6
    ignore in7
    ignore in8
    ignore cpu0_vid
    ignore fan1
    ignore fan2
    ignore fan3
    ignore temp1
    ignore temp2
    ignore temp3
 
bus "i2c-0" "SMBus I801 adapter at 0400"

chip "w83795adg-i2c-0-2f"

# Voltages ; note that in the table above, the .008 and .024 factors are
# already computed in the driver...

    label in0 "CPU1"
    label in1 "CPU2"
    label in2 "+1.5V"
    label in3 "+5V"
    label in4 "+12V"
    label in5 "5VSB"
    label in12 "+3.3V"
    label in13 "3VSB"
    label in14 "Vbat"

    compute in3 @*4, @/4
    compute in4 @*6.62, @/6.62
    compute in5 @*4, @/4

    label temp5 "mobo"
    label temp7 "CPU2"
    label temp8 "CPU1"

    ignore in6
    ignore in7
    ignore in11
    ignore temp3
    ignore temp4

    set in0_min  0.82
    set in0_max  1.35
    set in1_min  0.82
    set in1_max  1.35
    set in12_min  3.3 * 0.90
    set in12_max  3.3 * 1.05
    set in13_min  3.3 * 0.95
    set in13_max  3.3 * 1.10
    set in14_min  3.0 * 0.90
    set in14_max  3.3 * 1.10