mirror of
https://github.com/lm-sensors/lm-sensors.git
synced 2026-11-12 16:50:15 +00:00
Tele42
1398ef0201
This is a bulk recovery of the sensor configs found at https://web.archive.org/web/20150901092438/http://www.lm-sensors.org:80/wiki/Configurations The config sections themselves are unaltered, but I've selectively added some, but not all of the extra info around them. Anywhere there's been extra info added, it should be in comments at the top of the config, followed by a double newline to indicate the separation. Attribution has been retained where possible, but links to the mailing list are hosed, so goto the above archive.org link to check if a config has extra origin notes. [groeck: reformatted description] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
91 lines
2.9 KiB
Plaintext
91 lines
2.9 KiB
Plaintext
# Configuration file for the Gigabyte GA-870A-USB3,
|
|
# contributed by Gary Myers and Zeke Fast.
|
|
|
|
|
|
# libsensors3 configuration file for the Gigabyte GA-870A-USB3
|
|
# 2011-06-16 Gary Myers
|
|
# Updates welcome.
|
|
|
|
# CPU sensor
|
|
|
|
chip "k10temp-*"
|
|
|
|
label temp1 "CPU Temp (K10)" # Set for gnome-sensors-applet.
|
|
# See second CPU temp below.
|
|
|
|
# Motherboard sensors
|
|
|
|
chip "it8720-isa-*"
|
|
|
|
### Voltages
|
|
|
|
label in0 "Vcore"
|
|
label in1 "DDR3 1.5V" # as labelled in the BIOS.
|
|
label in2 "+3.3V"
|
|
label in3 "+5V" # Not shown in BIOS.
|
|
label in4 "+12V"
|
|
ignore in5 # Ambiguous - ignoring.
|
|
ignore in6 # Ambiguous - ignoring.
|
|
label in7 "5VSB" # Not shown in BIOS.
|
|
label in8 "Vbat" # Not shown in BIOS.
|
|
ignore cpu0_vid
|
|
|
|
# "Vcore", "DDR3 1.5V", "+3.3V" and "Vbat" are connected directly, so no compute
|
|
# line is needed for these. +5V and 5VSB are internal so we use the
|
|
# standard scaling factor. Scaling for +12V is apparently not standard,
|
|
# factor 3.963 is guessed from BIOS and EasyTune values (3.943 was
|
|
# another candidate.)
|
|
compute in3 @ * (6.8/10+1), @ / (6.8/10+1)
|
|
compute in4 @ * 3.963, @ / 3.963
|
|
compute in7 @ * (6.8/10+1), @ / (6.8/10+1)
|
|
|
|
# The BIOS will not set any limit for voltages.
|
|
|
|
set in0_min 0.825 * 0.95
|
|
set in0_max 1.425 * 1.05
|
|
set in1_min 1.5 * 0.95
|
|
set in1_max 1.5 * 1.05
|
|
set in2_min 3.3 * 0.95
|
|
set in2_max 3.3 * 1.05
|
|
set in3_min 5 * 0.95
|
|
set in3_max 5 * 1.05
|
|
set in4_min 12 * 0.95
|
|
set in4_max 12 * 1.05
|
|
set in7_min 5 * 0.95
|
|
set in7_max 5 * 1.05
|
|
|
|
### Temperatures
|
|
|
|
label temp1 "System Temp"
|
|
# This sensor appears to be around or inside the ITE8720F chip.
|
|
# The temperature drops if the chip and board area are cooled with
|
|
# freezer spray. This sensor may be over-reading!
|
|
# Adjustment applied to match internal case thermal sensor from my Antec P160.
|
|
compute temp1 (@ -20), (@ + 20)
|
|
set temp1_min 0
|
|
set temp1_max 50 # Tropical ambient max plus a bit
|
|
|
|
label temp2 "CPU Temp"
|
|
# This sensor can show 2 degrees difference to the K10 sensor.
|
|
# The end user can choose which one they prefer.
|
|
set temp2_min 0
|
|
set temp2_max 70 # Set to match your BIOS "CPU Warning Temperature"
|
|
|
|
ignore temp3 # No idea what this sensor is for. It always shows
|
|
# +78 deg C regardless of BIOS settings.
|
|
|
|
### Fans
|
|
|
|
# Label based on motherboard connectors.
|
|
label fan1 "CPU Fan" # M/B label: CPU_FAN (4-pin - near ATX 12V)
|
|
label fan5 "Power Fan" # M/B label: PWR_FAN (3-pin - near ATX)
|
|
label fan2 "System Fan 1" # M/B label: SYS_FAN1 (4-pin - near F_PANEL)
|
|
label fan3 "System Fan 2" # M/B label: SYS_FAN2 (3-pin - near SATA3_4)
|
|
|
|
# Minimum fan speeds.
|
|
# Comment/un-comment fan headers you are using if you want alarms.
|
|
set fan1_min 300 # CPU Fan
|
|
set fan5_min 300 # Power Fan
|
|
#set fan2_min 300 # System Fan 1
|
|
set fan3_min 300 # System Fan 2
|