mirror of
https://github.com/lm-sensors/lm-sensors.git
synced 2026-10-21 11:39:31 +00:00
Jean Delvare
820bd2eda7
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@4331 7894878c-1315-0410-8ee3-d5d059ff63e0
76 lines
2.8 KiB
Plaintext
76 lines
2.8 KiB
Plaintext
Kernel driver `smsc47m1.o'
|
|
==========================
|
|
|
|
Status: Beta.
|
|
|
|
Supported chips:
|
|
* SMSC LPC47B27x, LPC47M112, LPC47M10x, LPC47M13x, LPC47M14x,
|
|
LPC47M15x and LPC47M192
|
|
Prefix: 'smsc47m1'
|
|
Addresses scanned: none, address read from Super I/O config space
|
|
Datasheets:
|
|
http://www.smsc.com/main/datasheets/47b27x.pdf
|
|
http://www.smsc.com/main/datasheets/47m10x.pdf
|
|
http://www.smsc.com/main/datasheets/47m112.pdf
|
|
http://www.smsc.com/main/tools/discontinued/47m13x.pdf
|
|
http://www.smsc.com/main/datasheets/47m14x.pdf
|
|
http://www.smsc.com/main/tools/discontinued/47m15x.pdf
|
|
http://www.smsc.com/main/datasheets/47m192.pdf
|
|
* SMSC LPC47M292
|
|
Prefix: 'smsc47m2'
|
|
Addresses scanned: none, address read from Super I/O config space
|
|
Datasheet: Not public
|
|
* SMSC LPC47M997
|
|
Addresses scanned: none, address read from Super I/O config space
|
|
Prefix: 'smsc47m1'
|
|
Datasheet: none
|
|
|
|
Authors: Mark D. Studebaker <mdsxyz123@yahoo.com>
|
|
With assistance from Bruce Allen <ballen@uwm.edu> and his
|
|
fan.c program: http://www.lsc-group.phys.uwm.edu/%7Eballen/driver/
|
|
|
|
Module Parameters
|
|
-----------------
|
|
|
|
force_addr=0xaddr Set the I/O base address. Useful for boards
|
|
that don't set the address in the BIOS.
|
|
Don't use this unless the driver complains that the
|
|
base address is not set.
|
|
Example: 'modprobe smsc47m1 force_addr=0x680'
|
|
|
|
|
|
Description
|
|
-----------
|
|
|
|
The Standard Microsystems Corporation (SMSC) 47M1xx Super I/O chips
|
|
contain monitoring and PWM control circuitry for two fans.
|
|
|
|
The LPC47M15x, LPC47M192 and LPC47M292 chips contain a full 'hardware
|
|
monitoring block' in addition to the fan monitoring and control. The
|
|
hardware monitoring block is not supported by the driver.
|
|
|
|
No documentation is available for the 47M997, but it has the same device
|
|
ID as the 47M15x and 47M192 chips and seems to be compatible therewith.
|
|
|
|
Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
|
|
triggered if the rotation speed has dropped below a programmable limit. Fan
|
|
readings can be divided by a programmable divider (1, 2, 4 or 8) to give
|
|
the readings more range or accuracy. Not all RPM values can accurately be
|
|
represented, so some rounding is done. With a divider of 2, the lowest
|
|
representable value is around 2600 RPM.
|
|
|
|
PWM values are from 0 to 255. The first value in the /proc entry is
|
|
the pwm value; the second is the enable (0 or 1).
|
|
|
|
If an alarm triggers, it will remain triggered until the hardware register
|
|
is read at least once. This means that the cause for the alarm may
|
|
already have disappeared! Note that in the current implementation, all
|
|
hardware registers are read whenever any data is read (unless it is less
|
|
than 1.5 seconds since the last update). This means that you can easily
|
|
miss once-only alarms.
|
|
|
|
|
|
**********************
|
|
The lm_sensors project gratefully acknowledges the support of
|
|
Intel in the development of this driver.
|