mirror of
https://github.com/lm-sensors/lm-sensors.git
synced 2026-11-09 16:21:51 +00:00
Tele42
1398ef0201
This is a bulk recovery of the sensor configs found at https://web.archive.org/web/20150901092438/http://www.lm-sensors.org:80/wiki/Configurations The config sections themselves are unaltered, but I've selectively added some, but not all of the extra info around them. Anywhere there's been extra info added, it should be in comments at the top of the config, followed by a double newline to indicate the separation. Attribution has been retained where possible, but links to the mailing list are hosed, so goto the above archive.org link to check if a config has extra origin notes. [groeck: reformatted description] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
127 lines
4.7 KiB
Plaintext
127 lines
4.7 KiB
Plaintext
# Configuration file contributed by Charles A. from India.
|
|
|
|
|
|
# libsensors configuration file for Gigabyte GA-MA770-DS3 motherboard
|
|
|
|
chip "it8718-*"
|
|
|
|
# lmsensors' values were compared with values from monitoring
|
|
# software running on the same computer under Windows XP SP2
|
|
# abbreviated in comments:
|
|
# ET6: Gigabyte's EasyTune 6
|
|
# Everest: Lavalys's Everest Ultimate 4.6.0 (trial version)
|
|
# OverDrive: AMD's OverDrive 2.1.5
|
|
|
|
# Labels are copied from BIOS setup screens when value shown
|
|
|
|
# Voltages
|
|
|
|
label in0 "Vcore"
|
|
# BIOS: 1.264V, ET6: 1.260, Everest: 1.26, OverDrive: 1.26
|
|
# No scaling so no compute
|
|
# Values seen using powernow-k8 in "on demand" mode:
|
|
# 1.06, 1.07, 1.25, 1.26, 1.28
|
|
# Nominal values written to /var/log/kern.log by powernow-k8
|
|
# as vid numbers in hex. For AMD K8, these translate to V by
|
|
# 1.550 - 0.025 * vid. Gave 1.000, 1.175 and 1.200 V
|
|
set in0_min 1.000 * 0.95 # 95% of nominal min
|
|
set in0_max 1.200 * 1.05 # 105% of nominal max
|
|
|
|
label in1 "DDR2 1.8V"
|
|
# No scaling so no compute
|
|
set in1_min 1.8 * 0.95 # 95% of nominal
|
|
set in1_max 1.8 * 1.05 # 105% of nominal
|
|
|
|
label in2 "+3.3V"
|
|
# No scaling so no compute
|
|
set in2_min 3.3 * 0.95 # 95% of nominal
|
|
set in2_max 3.3 * 1.05 # 105% of nominal
|
|
|
|
label in3 "Vcc"
|
|
# BIOS: -, ET6: -, Everest: -, OverDrive: -
|
|
# dmesg reports as VCC
|
|
# Assume standard Winbond scaling resistors
|
|
compute in3 @ * ((6.8/10)+1), @ / ((6.8/10)+1)
|
|
set in3_min 5 * 0.95 # 95% of nominal
|
|
set in3_max 5 * 1.05 # 105% of nominal
|
|
|
|
label in4 "5VSB?" # Guess
|
|
# BIOS: -, ET6: -, Everest: -, OverDrive (VIN4): 12.74
|
|
# Values seen: 3.15, 3.17, 3.19
|
|
# Assume standard Winbond scaling resistors
|
|
compute in4 @ * ((6.8/10)+1), @ / ((6.8/10)+1)
|
|
set in4_min 5 * 0.95 # 95% of nominal
|
|
set in4_max 5 * 1.05 # 105% of nominal
|
|
|
|
label in5 "+12V"
|
|
# BIOS: 12.619V, ET6: 12.610, Everest: -, OverDrive: -
|
|
# Assume standard Winbond scaling resistors
|
|
compute in5 @ * ((30/10)+1), @ / ((30/10)+1)
|
|
set in5_min 12 * 0.95 # 95% of nominal
|
|
set in5_max 12 * 1.05 # 105% of nominal
|
|
|
|
ignore in6 # Seen always 4.08, too big (max 4.096) to signify
|
|
ignore in7 # Seen always 0.03, too small to be significant
|
|
|
|
label in8 "Vbat"
|
|
# BIOS: -, ET6: -, Everest: 3.17, OverDrive: -
|
|
# Connected directly so no compute
|
|
# in8_min and _max not supported by chip
|
|
|
|
ignore cpu0_vid # Not dynamic under lm-sensors 3.0.0
|
|
|
|
# Temperatures
|
|
|
|
label temp1 "Current System Temperature"
|
|
# BIOS: 30, ET6: 30, Everest: 33, OverDrive: -
|
|
compute temp1 @ -5, @ +5 # Correct bad sensor on Charles' mobo
|
|
set temp1_min 0
|
|
set temp1_max 45 # Tropical ambient max plus a bit
|
|
|
|
label temp2 "Current CPU Casing Temperature"
|
|
# BIOS: 29, ET6: 28, Everest: 32, OverDrive (both cores): 33
|
|
set temp2_min 0
|
|
# Max is lowest available BIOS "CPU Warning Temperature" - 5
|
|
set temp2_max 55
|
|
|
|
ignore temp3
|
|
# Values seen: 77-79, rising from cold start.
|
|
# Sheilding Northbridge from CPU cooling draft did not change
|
|
|
|
# Fans
|
|
# The labels chosen are the ones printed on the motherboard
|
|
label fan1 "CPU_FAN"
|
|
set fan1_min 0 # fancontrol may stop fan
|
|
label fan2 "SYS_FAN1"
|
|
label fan3 "SYS_FAN2"
|
|
ignore fan4 # "NB_FAN" does not set an RPM signal
|
|
label fan5 "PWR_FAN"
|
|
|
|
# Beep
|
|
# lm-sensors 3.0.0 does not support on this chip
|
|
# Was enabled by default
|
|
|
|
chip "k8temp-*"
|
|
|
|
# Temperatures
|
|
# For CPU revisions F and G, according to AMD's "Revision
|
|
# Guide for AMD NPT Family 0Fh Processors", "The internal
|
|
# thermal sensor ... is inaccurate". This may be the reason
|
|
# for many reports of k8temp giving absurdly low CPU core
|
|
# temperatures and for there being no generally accepted
|
|
# computation to derive actual temperature from the raw data.
|
|
# The workaround is to ignore core temperatures and use the
|
|
# CPU case temperature as was done before core temperatures
|
|
# were available. On this motherboard the CPU case temperature
|
|
# is reported by the it8718 chip's temp2 (see above).
|
|
|
|
# For CPU revisions other than F and G, the proper use of
|
|
# k8temp temperatures may be to compute an average for each
|
|
# core rather than to report two temperatures for each core.
|
|
# For a sample computation see mingus' posting at
|
|
# http://forums.opensuse.org/archives/sls-archives/archives-suse-linux/archives-hardware-support/381563-lm-sensors-2.html#post1793098
|
|
|
|
# If you don't trust the readings, you might as well not load
|
|
# the k8temp driver (which, in practice, means blacklisting it,
|
|
# as this driver auto-loads on most systems.
|