mirror of
https://github.com/lm-sensors/lm-sensors.git
synced 2026-11-21 19:51:45 +00:00
This is a bulk recovery of the sensor configs found at https://web.archive.org/web/20150901092438/http://www.lm-sensors.org:80/wiki/Configurations The config sections themselves are unaltered, but I've selectively added some, but not all of the extra info around them. Anywhere there's been extra info added, it should be in comments at the top of the config, followed by a double newline to indicate the separation. Attribution has been retained where possible, but links to the mailing list are hosed, so goto the above archive.org link to check if a config has extra origin notes. [groeck: reformatted description] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
94 lines
3.4 KiB
Plaintext
94 lines
3.4 KiB
Plaintext
# Configuration file contributed by Martin Herrman.
|
|
|
|
|
|
# LM-Sensors config file for Gigabyte GA-Z38MX-UD2H-B3 mainboard with
|
|
# an Intel i5 Sandy Bridge quad core CPU installed.
|
|
|
|
# Tested with kernel 3.10.x and lm-sensors 3.3.x on Gentoo Linux.
|
|
|
|
# Created by Martin Herrman <martin@herrman.nl> with help from Jean Delvare
|
|
# from the lm-sensors mailinglist.
|
|
|
|
# Questions, comments or additions? Please share on the lm-sensors mailinglist.
|
|
# More info at http://www.lm-sensors.org/wiki/FeedbackAndSupport
|
|
|
|
# Hint: Use sensors -u to list all variables.
|
|
http://lists.lm-sensors.org/pipermail/lm-sensors/2014-January/040952.html
|
|
chip "coretemp-*"
|
|
# chip coretemp measures cpu temperatures from i5 CPU temperature sensor
|
|
# _max, _crit and _crit_alarm are read from the cpu itself
|
|
# when temp is at _max, all cooling options must be at full throttle
|
|
# when temp is at _crit, cpu starts to fail
|
|
# _crit_alarm is automatically set by hardware when _input is at or above _crit
|
|
# libsensors currently doesn't support the trigger of a notification system
|
|
label temp1 "CPU Package temp"
|
|
label temp2 "Core 0"
|
|
label temp3 "Core 1"
|
|
label temp4 "Core 2"
|
|
label temp5 "Core 3"
|
|
|
|
# IT8728F is on the mainboard and provides voltages and cpu/case fan speed
|
|
chip "it8728-*"
|
|
|
|
# scythe kozuti min = 800
|
|
# output of sensors will show ALARM (_alarm is set to 1) when actual fan
|
|
# speed (_input) is below set minimum (_min). If _beep is set to 1, and
|
|
# the motherboard is wired between the temperature sehttp://lists.lm-sensors.org/pipermail/lm-sensors/2014-January/040952.htmlnsor and the
|
|
# PC speaker, the PC speaker will start beeping.
|
|
# Unfortunately Gigabyte GA-Z68MX-UD2H-B3 is not properly wired.
|
|
label fan1 "CPU fan"
|
|
set fan1_min 800
|
|
set fan1_beep 1
|
|
|
|
# I don't have a case fan installed via PWM
|
|
label fan2 "Case fan"
|
|
#set fan2_min 1000
|
|
#set fan2_beep 1
|
|
|
|
# Motherboard temps
|
|
|
|
# Note: tempX_type indicates the type of sensor and is set by the BIOS
|
|
|
|
# When comparing temp1 and temp2 with BIOS value, temp1 seems to be similar to BIOS system temperature.
|
|
# temp2 increases like temp1 does, so I assume that it is another case temp but not shown in BIOS.
|
|
label temp1 "Case temp (shown in BIOS)"
|
|
label temp2 "Case temp (hidden in BIOS)"
|
|
|
|
# The reported values seem to be correct. No need to add offset or compute.
|
|
|
|
# Let's set some real world values for min and max
|
|
set temp1_min 25
|
|
set temp1_max 50
|
|
set temp2_min 25
|
|
set temp2_max 50
|
|
|
|
# Let's alarm when temperatures are outside range
|
|
set temp1_beep 1
|
|
set temp2_beep 1
|
|
|
|
# temp3 increases when cpu high load, so assuming this is CPU temperature.
|
|
label temp3 "CPU temp"
|
|
|
|
# Note: PECI value is negative value relative to _crit, but driver calculates
|
|
# to real value.
|
|
|
|
# Adding 10 to correct wrong BIOS values.
|
|
# Change offset is more efficient than computing new value, because offset is done in hardware.
|
|
# Note: using compute also increases min and max values. You will need to set the min and max values below.
|
|
# Note: offset default value is 72, so add 10 makes 82.
|
|
#compute temp3 @+10,@-10
|
|
set temp3_offset 82
|
|
|
|
# In BIOS it is possible to set CPU warning temperature, but this does not influence
|
|
# temp3_input. However, it does change the temp3_max. My bios setting is at 60
|
|
# degrees. Coretemp defines maximum of 76. I want a warning at 60.
|
|
# _min, _max
|
|
set temp3_min 25
|
|
#set temp3_max 60
|
|
|
|
# Let's alarm when temperature is outside range
|
|
set temp3_beep 1
|
|
|
|
# ignore intrusion detection (case open?)
|
|
ignore intrusion0
|