mirror of
https://github.com/lm-sensors/lm-sensors.git
synced 2026-10-28 12:40:42 +00:00
Mark M. Hoffman
57320d467a
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@2653 7894878c-1315-0410-8ee3-d5d059ff63e0
207 lines
5.9 KiB
Plaintext
207 lines
5.9 KiB
Plaintext
Kernel driver 'lm93.o'
|
|
======================
|
|
|
|
Status: In progress
|
|
|
|
Supported chips:
|
|
* National Semiconductor LM93
|
|
Prefix 'lm93'
|
|
Addresses scanned: I2C 0x2c-0x2e
|
|
|
|
Author:
|
|
Mark M. Hoffman <mhoffman@lightlink.com>
|
|
|
|
|
|
Module Parameters
|
|
-----------------
|
|
|
|
(specific to LM93)
|
|
* init: integer
|
|
Set to zero to disable some initializations (default is 1)
|
|
* disable_block: integer
|
|
Set to non-zero to disable SMBus block data transactions (default is 0)
|
|
* vccp_limit_type: integer array (2)
|
|
Configures in7 and in8 limit type, where 0 means absolute and non-zero
|
|
means relative. "Relative" here refers to "Dynamic Vccp Monitoring using
|
|
VID" from the datasheet. It greatly simplifies the interface to allow
|
|
only one set of limits (absolute or relative) to be in operation at a
|
|
time (even though the hardware is capable of enabling both). There's
|
|
not a compelling use case for enabling both at once, anyway. The default
|
|
is "0,0".
|
|
|
|
(common among sensor drivers)
|
|
* force: short array (min = 1, max = 48)
|
|
List of adapter,address pairs to assume to be present. Autodetection
|
|
of the target device will still be attempted. Use one of the more
|
|
specific force directives below if this doesn't detect the device.
|
|
* force_lm93: short array (min = 1, max = 48)
|
|
List of adapter,address pairs which are unquestionably assumed to contain
|
|
a 'lm93' chip
|
|
* ignore: short array (min = 1, max = 48)
|
|
List of adapter,address pairs not to scan
|
|
* ignore_range: short array (min = 1, max = 48)
|
|
List of adapter,start-addr,end-addr triples not to scan
|
|
* probe: short array (min = 1, max = 48)
|
|
List of adapter,address pairs to scan additionally
|
|
* probe_range: short array (min = 1, max = 48)
|
|
List of adapter,start-addr,end-addr triples to scan additionally
|
|
|
|
|
|
Hardware Description
|
|
--------------------
|
|
|
|
(from the datasheet)
|
|
|
|
The LM93, hardware monitor, has a two wire digital interface compatible with
|
|
SMBus 2.0. Using an 8-bit ADC, the LM93 measures the temperature of two remote
|
|
diode connected transistors as well as its own die and 16 power supply
|
|
voltages. To set fan speed, the LM93 has two PWM outputs that are each
|
|
controlled by up to four temperature zones. The fancontrol algorithm is lookup
|
|
table based. The LM93 includes a digital filter that can be invoked to smooth
|
|
temperature readings for better control of fan speed. The LM93 has four
|
|
tachometer inputs to measure fan speed. Limit and status registers for all
|
|
measured values are included. The LM93 builds upon the functionality of
|
|
previous motherboard management ASICs and uses some of the LM85 s features
|
|
(i.e. smart tachometer mode). It also adds measurement and control support
|
|
for dynamic Vccp monitoring and PROCHOT. It is designed to monitor a dual
|
|
processor Xeon class motherboard with a minimum of external components.
|
|
|
|
|
|
Driver Description
|
|
------------------
|
|
|
|
This driver implements support for the National Semiconductor LM93.
|
|
|
|
|
|
User Interface
|
|
--------------
|
|
|
|
#PROCHOT:
|
|
|
|
The LM93 can monitor two #PROCHOT signals. The results are found in the
|
|
/proc files prochot1 and prochot2. There are two values per file: the first
|
|
value is the user limit. The second value is the current reading for the
|
|
most recent complete time interval. The third value is something like a
|
|
2 period exponential moving average (but not quite - check the datasheet).
|
|
Note that this third value is calculated by the chip itself. All values
|
|
range from 0-255 where 0 indicates no throttling, and 255 indicates > 99.6%.
|
|
|
|
It is possible to configure the LM93 to logically short the two #PROCHOT
|
|
signals. I.e. when #P1_PROCHOT is asserted, the LM93 will automatically
|
|
assert #P2_PROCHOT, and vice-versa. This mode is enabled by writing a
|
|
non-zero integer to the /proc file prochot_short.
|
|
|
|
|
|
Smart Tach Mode:
|
|
|
|
(from the datasheet)
|
|
|
|
If a fan is driven using a low-side drive PWM, the tachometer
|
|
output of the fan is corrupted. The LM93 includes smart tachometer
|
|
circuitry that allows an accurate tachometer reading to be
|
|
achieved despite the signal corruption. In smart tach mode all
|
|
four signals are measured within 4 seconds.
|
|
|
|
Smart tach mode is enabled by the driver by writing 1 or 2 (associating the
|
|
the fan tachometer with a pwm) to the /proc file fan<n>_smart_tach. A zero
|
|
will disable the function for that fan.
|
|
|
|
LM93 Unique /proc Files
|
|
-----------------------
|
|
|
|
file description
|
|
-------------------------------------------------------------
|
|
|
|
prochot<n> limit, current, and moving average #PROCHOT %
|
|
|
|
prochot_short enable or disable logical #PROCHOT pin short
|
|
|
|
fan<n>_smart_tach enable or disable smart tach mode
|
|
|
|
|
|
Sample Configuration File
|
|
-------------------------
|
|
|
|
Here is a sample LM93 chip config for sensors.conf:
|
|
|
|
---------- cut here ----------
|
|
chip "lm93-*"
|
|
|
|
# VOLTAGE INPUTS
|
|
|
|
# labels and scaling based on datasheet recommendations
|
|
label in1 "+12V1"
|
|
compute in1 @ * 12.945, @ / 12.945
|
|
set in1_min 12 * 0.90
|
|
set in1_max 12 * 1.10
|
|
|
|
label in2 "+12V2"
|
|
compute in2 @ * 12.945, @ / 12.945
|
|
set in2_min 12 * 0.90
|
|
set in2_max 12 * 1.10
|
|
|
|
label in3 "+12V3"
|
|
compute in3 @ * 12.945, @ / 12.945
|
|
set in3_min 12 * 0.90
|
|
set in3_max 12 * 1.10
|
|
|
|
label in4 "FSB_Vtt"
|
|
|
|
label in5 "3GIO"
|
|
|
|
label in6 "ICH_Core"
|
|
|
|
label in7 "Vccp1"
|
|
|
|
label in8 "Vccp2"
|
|
|
|
label in9 "+3.3V"
|
|
set in9_min 3.3 * 0.90
|
|
set in9_max 3.3 * 1.10
|
|
|
|
label in10 "+5V"
|
|
set in10_min 5.0 * 0.90
|
|
set in10_max 5.0 * 1.10
|
|
|
|
label in11 "SCSI_Core"
|
|
|
|
label in12 "Mem_Core"
|
|
|
|
label in13 "Mem_Vtt"
|
|
|
|
label in14 "Gbit_Core"
|
|
|
|
# Assuming R1/R2 = 4.1143, and 3.3V reference
|
|
# -12V = (4.1143 + 1) * (@ - 3.3) + 3.3
|
|
label in15 "-12V"
|
|
compute in15 @ * 5.1143 - 13.57719, (@ + 13.57719) / 5.1143
|
|
set in15_min -12 * 0.90
|
|
set in15_max -12 * 1.10
|
|
|
|
label in16 "+3.3VSB"
|
|
set in16_min 3.3 * 0.90
|
|
set in16_max 3.3 * 1.10
|
|
|
|
# TEMPERATURE INPUTS
|
|
|
|
label temp1 "CPU1"
|
|
label temp2 "CPU2"
|
|
label temp3 "LM93"
|
|
|
|
# TACHOMETER INPUTS
|
|
|
|
label fan1 "Fan1"
|
|
set fan1_min 3000
|
|
label fan2 "Fan2"
|
|
set fan2_min 3000
|
|
label fan3 "Fan3"
|
|
set fan3_min 3000
|
|
label fan4 "Fan4"
|
|
set fan4_min 3000
|
|
|
|
# PWM OUTPUTS
|
|
|
|
label pwm1 "CPU1"
|
|
label pwm2 "CPU2"
|
|
|