mirror of
https://github.com/lm-sensors/lm-sensors.git
synced 2026-10-18 11:09:32 +00:00
Mark D. Studebaker
0195d22c57
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1736 7894878c-1315-0410-8ee3-d5d059ff63e0
148 lines
7.9 KiB
Plaintext
148 lines
7.9 KiB
Plaintext
Kernel driver `gl520sm.o'
|
|
=========================
|
|
|
|
Status: Complete but experimental
|
|
|
|
Supported chips:
|
|
* Genesys Logic GL520SM release 0x00
|
|
Prefix `gl520sm'
|
|
Addresses scanned: I2C 0x2c and 0x2d
|
|
Datasheet: Not openly available
|
|
|
|
Author: Frodo Looijaard <frodol@dds.nl>,
|
|
Kyösti Mälkki <kmalkki@cc.hut.fi>
|
|
|
|
|
|
Module Parameters
|
|
-----------------
|
|
|
|
* force: short array (min = 1, max = 48)
|
|
List of adapter,address pairs to boldly assume to be present
|
|
* ignore: short array (min = 1, max = 48)
|
|
List of adapter,address pairs not to scan
|
|
* ignore_range: short array (min = 1, max = 48)
|
|
List of adapter,start-addr,end-addr triples not to scan
|
|
* probe: short array (min = 1, max = 48)
|
|
List of adapter,address pairs to scan additionally
|
|
* probe_range: short array (min = 1, max = 48)
|
|
List of adapter,start-addr,end-addr triples to scan additionally
|
|
|
|
Description
|
|
-----------
|
|
|
|
This driver supports the Genesys Logic GL520SM chip.
|
|
|
|
The GL520SM implements one temperature sensor, two FAN rotation speed
|
|
sensors, four voltage sensors and the cpu VID lines. In addition, one input
|
|
can be configured as either a temperature or voltage sensor.
|
|
The sensor can report alarms through the computer speakers.
|
|
|
|
Temperatures are measured in degrees Celcius. An alarm goes off while the
|
|
temperature is above the over temperature limit, and has not yet dropped
|
|
below the hysteresis limit. The alarm always reflects the current situation.
|
|
Measurements are guaranteed between 0 degrees and +110 degrees, with
|
|
a resolution of +-3 degrees.
|
|
|
|
FAN rotation speeds are reported in RPM (rotations per minute). An alarm is
|
|
triggered if the rotation speed has dropped below a programmable limit.
|
|
In case when you have selected to turn Fan1 off, no Fan1 alarm is triggered
|
|
if measured temperature is below 'over temperature' limit.
|
|
|
|
FAN readings can be divided by a programmable divider (1, 2, 4 or 8) to give
|
|
the readings more range or accuracy. This is important because some FANs
|
|
report only one 'tick' each rotation, while others report two.
|
|
Not all RPM values can accurately be represented, so some rounding is done.
|
|
With a divider of 2, the lowest representable value is around 1900 RPM.
|
|
|
|
Voltage sensors (also known as VIN sensors) report their values in volts. An
|
|
alarm is triggered if the voltage has crossed a programmable minimum or
|
|
maximum limit. Note that minimum in this case always means 'closest to
|
|
zero'; this is important for negative voltage measurements. The VDD input
|
|
measures voltages between 0.000 and 5.865 volt, with a resolution of 0.023
|
|
volt. The other inputs measure voltages between 0.000 and 4.845 volt, with a
|
|
resolution of 0.019 volt.
|
|
|
|
When an alarm goes off, you can be warned by a beeping signal through
|
|
your computer speaker. It is possible to enable all beeping globally,
|
|
or only the beeping for some alarms.
|
|
|
|
If an alarm triggers, it will remain triggered until the hardware register
|
|
is read at least once (except for temperature alarms). This means that the
|
|
cause for the alarm may already have disappeared! Note that in the current
|
|
implementation, all hardware registers are read whenever any data is read
|
|
(unless it is less than 1.5 seconds since the last update). This means that
|
|
you can easily miss once-only alarms.
|
|
|
|
The GL520SM only updates its values each 1.5 seconds; reading it more often
|
|
will do no harm, but will return 'old' values.
|
|
|
|
Chip Features
|
|
-------------
|
|
|
|
Chip `gl520sm'
|
|
LABEL LABEL CLASS COMPUTE CLASS ACCESS MAGNITUDE
|
|
vdd NONE NONE R 2
|
|
vin1 NONE NONE R 2
|
|
vin2 NONE NONE R 2
|
|
vin3 NONE NONE R 2
|
|
vin4 NONE NONE R 2
|
|
vdd_min vdd vdd RW 2
|
|
vin1_min vin1 vin1 RW 2
|
|
vin2_min vin2 vin2 RW 2
|
|
vin3_min vin3 vin3 RW 2
|
|
vin4_min vin4 vin4 RW 2
|
|
vdd_max vdd vdd RW 2
|
|
vin1_max vin1 vin1 RW 2
|
|
vin2_max vin2 vin2 RW 2
|
|
vin3_max vin3 vin3 RW 2
|
|
vin4_max vin4 vin4 RW 2
|
|
fan1 NONE NONE R 0
|
|
fan2 NONE NONE R 0
|
|
fan1_min fan1 fan1 RW 0
|
|
fan2_min fan2 fan2 RW 0
|
|
temp1 NONE NONE R 1
|
|
temp2 NONE NONE R 1
|
|
temp1_hyst temp1 temp1 RW 1
|
|
temp2_hyst temp2 temp2 RW 1
|
|
temp1_over temp1 temp1 RW 1
|
|
temp2_over temp2 temp2 RW 1
|
|
fan1_div fan1 NONE RW 0
|
|
fan2_div fan2 NONE RW 0
|
|
alarms NONE NONE R 0
|
|
beep_enable alarms NONE RW 0
|
|
beeps alarms alarms RW 0
|
|
two_temps NONE NONE RW 0
|
|
|
|
LABEL FEATURE SYMBOL SYSCTL FILE:NR
|
|
vdd SENSORS_GL520_VDD vdd:3
|
|
vin1 SENSORS_GL520_VIN1 vin1:3
|
|
vin2 SENSORS_GL520_VIN2 vin2:3
|
|
vin3 SENSORS_GL520_VIN3 vin3:3
|
|
vin4 SENSORS_GL520_VIN4 vin3:3
|
|
vdd_min SENSORS_GL520_VDD_MIN vdd:1
|
|
vin1_min SENSORS_GL520_VIN1_MIN vin1:1
|
|
vin2_min SENSORS_GL520_VIN2_MIN vin2:1
|
|
vin3_min SENSORS_GL520_VIN3_MIN vin3:1
|
|
vin4_min SENSORS_GL520_VIN4_MIN vin3:1
|
|
vdd_max SENSORS_GL520_VDD_MAX vdd:2
|
|
vin1_max SENSORS_GL520_VIN1_MAX vin1:2
|
|
vin2_max SENSORS_GL520_VIN2_MAX vin2:2
|
|
vin3_max SENSORS_GL520_VIN3_MAX vin3:2
|
|
vin4_max SENSORS_GL520_VIN4_MAX vin3:2
|
|
fan1 SENSORS_GL520_FAN1 fan1:2
|
|
fan2 SENSORS_GL520_FAN2 fan2:2
|
|
fan1_min SENSORS_GL520_FAN1_MIN fan1:1
|
|
fan2_min SENSORS_GL520_FAN2_MIN fan2:1
|
|
temp1 SENSORS_GL520_TEMP1 temp1:3
|
|
temp2 SENSORS_GL520_TEMP2 temp2:3
|
|
temp1_hyst SENSORS_GL520_TEMP1_HYST temp1:2
|
|
temp2_hyst SENSORS_GL520_TEMP2_HYST temp2:2
|
|
temp1_over SENSORS_GL520_TEMP1_OVER temp1:1
|
|
temp2_over SENSORS_GL520_TEMP2_OVER temp2:1
|
|
fan1_div SENSORS_GL520_FAN1_DIV fan_div:1
|
|
fan2_div SENSORS_GL520_FAN2_DIV fan_div:2
|
|
alarms SENSORS_GL520_ALARMS alarms:1
|
|
beep_enable SENSORS_GL520_BEEP_ENABLE beep:1
|
|
beeps SENSORS_GL520_BEEPS beep:2
|
|
two_temps SENSORS_GL520_TWOTEMPS config:1
|