wt/lm-sensors
1
0 Fork 0
mirror of https://github.com/lm-sensors/lm-sensors.git synced 2026-10-25 12:14:33 +00:00
Code Issues Packages Projects Releases Wiki Activity
Files
9b44cc28191c2dd5faea30eff5ffe018daa29708
lm-sensors/etc/sensors.conf.eg
T
Jean Delvare df4921b0b1 Winbond W83L771AWG/ASG support. 
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@5815 7894878c-1315-0410-8ee3-d5d059ff63e0
2010-01-13 20:18:02 +00:00

2172 lines
60 KiB
Plaintext
Raw Blame History

# libsensors configuration file
# -----------------------------
# NOTE:
# All the set statements from this file are commented out by default.
# The reason is that the proper limits are highly system-dependent,
# and writing improper limits may have all sorts of weird effects,
# from beeping to CPU throttling to instant reboot. If you want to
# actually set the limits, remove the comment marks, then run "sensors -s".
chip "lm78-*" "lm79-*" "w83781d-*"
# These are as advised in the LM78 and LM79 data sheets, and used on almost
# any mainboard we have seen.
label in0 "VCore 1"
label in1 "VCore 2"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
label in5 "-12V"
label in6 "-5V"
# For positive voltages (in3, in4), two resistors are used, with the following
# formula (R1,R2: resistor values, Vs: read voltage, Vin: pin voltage)
# R1 = R2 * (Vs/Vin - 1)
# For negative voltages (in5, in6) two resistors are used, with the following
# formula (Rin,Rf: resistor values, Vs: read voltage, Vin: pin voltage)
# Rin = (Vs * Rf) / Vin
#
# Here are the official LM78 and LM79 data sheet values.
# Vs R1,Rin R2,Rf Vin
# in3 +5.0 6.8 10 +2.98
# in4 +12.0 30 10 +3.00
# in5 -12.0 240 60 +3.00
# in6 -5.0 100 60 +3.00
#
# These would lead to these declarations:
# compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
# compute in4 ((30/10)+1)*@ , @/((30/10)+1)
# compute in5 -(240/60)*@ , -@/(240/60)
# compute in6 -(100/60)*@ , -@/(100/60)
#
# On almost any mainboard we have seen, the Winbond compute values lead to
# much better results, though.
#
# Vs R1,Rin R2,Rf Vin
# in4 +12.0 28 10 +3.15
# in5 -12.0 210 60.4 +3.45
# in6 -5.0 90.9 60.4 +3.33
#
# These leads to these declarations:
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((28/10)+1)*@ , @/((28/10)+1)
compute in5 -(210/60.4)*@ , -@/(210/60.4)
compute in6 -(90.9/60.4)*@ , -@/(90.9/60.4)
# Here, we assume the VID readings are valid, and we use a max. 5% deviation
# set in0_min cpu0_vid*0.95
# set in0_max cpu0_vid*1.05
# set in1_min cpu0_vid*0.95
# set in1_max cpu0_vid*1.05
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# set in3_min 5.0 * 0.95
# set in3_max 5.0 * 1.05
# set in4_min 12 * 0.95
# set in4_max 12 * 1.05
# set in5_min -12 * 0.95
# set in5_max -12 * 1.05
# set in6_min -5 * 0.95
# set in6_max -5 * 1.05
# Examples for lm78, lm79 temperature limits
# set temp1_max 40
# set temp1_max_hyst 37
# Examples for w83781d temperature limits
# set temp1_max 40
# set temp1_max_hyst 37
# set temp2_max 52
# set temp2_max_hyst 47
# set temp3_max 52
# set temp3_max_hyst 47
# Examples of fan low speed limits
# set fan1_min 3000
# set fan2_min 3000
# set fan3_min 3000
# Ignore fans you don't actually have
# ignore fan1
# ignore fan2
# ignore fan3
# In case a lm78 is used together with a lm75, the lm78 temp sensor will
# generally show the M/B temperature while the lm75 temp sensor will show
# the CPU temperature.
# label temp1 "M/B Temp"
# Uncomment the following line to enable beeps for all alarms on this chip
# set beep_enable 1
chip "lm75-*"
# Most boards don't need scaling. Following is for the Asus TX97-E.
# compute temp1 @*2.0, @/2.0
# Examples for temperature limits
# set temp1_max 70
# set temp1_max_hyst 65
# In case a lm75 is used together with a lm78, the lm78 temp sensor will
# generally show the M/B temperature while the lm75 temp sensor will show
# the CPU temperature.
# label temp1 "CPU Temp"
chip "sis5595-*"
label in0 "VCore 1"
label in1 "VCore 2"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((28/10)+1)*@ , @/((28/10)+1)
# set in0_min 2.0 * 0.95
# set in0_max 2.0 * 1.05
# set in1_min 2.0 * 0.95
# set in1_max 2.0 * 1.05
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# set in3_min 5.0 * 0.95
# set in3_max 5.0 * 1.05
# set in4_min 12 * 0.95
# set in4_max 12 * 1.05
#
# SiS5595 temperature calculation
# The driver currently includes a calculation due to the wide
# variation in thermistor types on SiS5595 motherboards.
# The driver currently has a calculation of t = (.83x + 52.12).
# One user reports the correct formula of t = (.345x - 12).
# So you want to put a compute line in sensors.conf that has
# the inverse of the driver formula, and put your formula on top of it.
# The inverse of the driver formula is x = (1.20t - 62.77)
# So the final formula is newt = (.345(1.20t - 62.77)) - 12).
# Put this in the sensors.conf file as
# compute temp1 ((.345 * ((1.20 * @) - 62.77)) - 12), ...
# where ... is the inverse function I leave to you.
#
# Look in your 'Vendor.ini' file to see which one is present
# on your motherboard. Look for the line like:
# [Temp1]
# ThermistorType = NTC-10KC15-1608-1P
# Fix up a 'compute' line to match your thermistor type.
# Warning. You still don't have enough information to do this.
# ThermistorType = NTC-10KC15-1608-1P (10K at 25C; Beta = 3435)
# compute temp1 ((X * ((1.20 * @) - 62.77)) - Y), ...
# ThermistorType = NTC-103KC15-1608-1P (??)
# compute temp1 ((X * ((1.20 * @) - 62.77)) - Y), ...
# ThermistorType = NTC-103AT-2 (10K at 25C; Beta = 3435)
# compute temp1 ((X * ((1.20 * @) - 62.77)) - Y), ...
# ThermistorType = NTC-103JT (10K at 25C; Beta = 3435)
# compute temp1 ((X * ((1.20 * @) - 62.77)) - Y), ...
# examples for sis5595 temperature limits;
# set temp1_max 40
# set temp1_max_hyst 37
chip "w83782d-*" "w83627hf-*"
# Same as above for w83781d except that in5 and in6 are computed differently.
# Rather than an internal inverting op amp, the 82d/83s use standard positive
# inputs and the negative voltages are level shifted by a 3.6V reference.
# The math is convoluted, so we hope that your motherboard
# uses the recommended resistor values.
label in0 "VCore 1"
label in1 "VCore 2"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
label in5 "-12V"
label in6 "-5V"
label in7 "V5SB"
label in8 "VBat"
# Abit BP6 motherboard has a few differences. VCore1 and VCore2 are the core
# voltages of the two processors. Vtt is memory bus termination resistors
# voltage.
# label in1 "Vtt"
# label in8 "VCore2"
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((28/10)+1)*@ , @/((28/10)+1)
compute in5 (5.14 * @) - 14.91 , (@ + 14.91) / 5.14
compute in6 (3.14 * @) - 7.71 , (@ + 7.71) / 3.14
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)
# set limits to 5% for the critical voltages
# set limits to 10% for the non-critical voltages
# set limits to 20% for the battery voltage
# set in0_min cpu0_vid*0.95
# set in0_max cpu0_vid*1.05
# set in1_min cpu0_vid*0.95
# set in1_max cpu0_vid*1.05
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# set in3_min 5.0 * 0.95
# set in3_max 5.0 * 1.05
# set in4_min 12 * 0.90
# set in4_max 12 * 1.10
# set in5_max -12 * 0.90
# set in5_min -12 * 1.10
# set in6_max -5 * 0.95
# set in6_min -5 * 1.05
# set in7_min 5 * 0.95
# set in7_max 5 * 1.05
# set in8_min 3.0 * 0.80
# set in8_max 3.0 * 1.20
# set up sensor types (thermistor is default)
# 1 = PII/Celeron Diode; 2 = 3904 transistor;
# 3435 = thermistor with Beta = 3435
# If temperature changes very little, try 1 or 2.
# set temp1_type 1
# set temp2_type 2
# set temp3_type 3435
# examples for temperature limits
# set temp1_max 40
# set temp1_max_hyst 37
# set temp2_max 52
# set temp2_max_hyst 47
# set temp3_max 52
# set temp3_max_hyst 47
chip "w83783s-*"
# Same as above for w83781d except that in5 and in6 are computed differently.
# Rather than an internal inverting op amp, the 82d/83s use standard positive
# inputs and the negative voltages are level shifted by a 3.6V reference.
# The math is convoluted, so we hope that your motherboard
# uses the recommended resistor values.
label in0 "VCore 1"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
label in5 "-12V"
label in6 "-5V"
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((28/10)+1)*@ , @/((28/10)+1)
compute in5 (5.14 * @) - 14.91 , (@ + 14.91) / 5.14
compute in6 (3.14 * @) - 7.71 , (@ + 7.71) / 3.14
# set limits to 5% for the critical voltages
# set limits to 10% for the non-critical voltages
# set limits to 20% for the battery voltage
# set in0_min cpu0_vid*0.95
# set in0_max cpu0_vid*1.05
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# set in3_min 5.0 * 0.95
# set in3_max 5.0 * 1.05
# set in4_min 12 * 0.90
# set in4_max 12 * 1.10
# set in5_max -12 * 0.90
# set in5_min -12 * 1.10
# set in6_max -5 * 0.95
# set in6_min -5 * 1.05
# set up sensor types (thermistor is default)
# 1 = PII/Celeron Diode; 2 = 3904 transistor;
# 3435 = thermistor with Beta = 3435
# If temperature changes very little, try 1 or 2.
# set temp1_type 1
# set temp2_type 2
# examples for temperature limits
# set temp1_max 40
# set temp1_max_hyst 37
# set temp2_max 52
# set temp2_max_hyst 47
chip "w83697hf-*"
# Same as above for w83781d except that in5 and in6 are computed differently.
# Rather than an internal inverting op amp, the 82d/83s use standard positive
# inputs and the negative voltages are level shifted by a 3.6V reference.
# The math is convoluted, so we hope that your motherboard
# uses the recommended resistor values.
# no in1 on this chip.
label in0 "VCore"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
label in5 "-12V"
label in6 "-5V"
label in7 "V5SB"
label in8 "VBat"
# Tyan Trinity S2495 KT400 has a few differences. Thanks to Eric Schumann
# for proving this information. Same is true for Epox 8K3A and 8KHA+.
# Thanks to Thomas Schorpp for additional feedback.
# label in2 "VAgp"
# label in5 "+3.3V" # aka. Vio
# label in6 "Vdimm"
# label in7 "VBat"
# label in8 "V5SB"
#
# You'll also want to comment out the in5 and in6 compute lines right below,
# and rename compute in7 to compute in8.
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((28/10)+1)*@ , @/((28/10)+1)
compute in5 (5.14 * @) - 14.91 , (@ + 14.91) / 5.14
compute in6 (3.14 * @) - 7.71 , (@ + 7.71) / 3.14
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)
# 697HF does not have VID inputs so you MUST set your core
# voltage limits below. Currently set for 1.8V core.
# vvv
# set in0_min 1.8 * 0.95
# set in0_max 1.8 * 1.05
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# set in3_min 5.0 * 0.95
# set in3_max 5.0 * 1.05
# set in4_min 12 * 0.90
# set in4_max 12 * 1.10
# set in5_max -12 * 0.90
# set in5_min -12 * 1.10
# set in6_max -5 * 0.95
# set in6_min -5 * 1.05
# set in7_min 5 * 0.95
# set in7_max 5 * 1.05
# set in8_min 3.0 * 0.80
# set in8_max 3.0 * 1.20
# And for Tyan Trinity S2495 KT400 and Epox 8K3A and 8KHA+:
# set in2_min 1.5 * 0.95
# set in2_max 1.5 * 1.05
# set in5_min 3.3 * 0.95
# set in5_max 3.3 * 1.05
# set in6_min 2.5 * 0.95 # 2.6 on Epox
# set in6_max 2.5 * 1.05 # 2.6 on Epox
# set in7_min 3.0 * 0.90
# set in7_max 3.0 * 1.10
# set in8_min 5 * 0.90
# set in8_max 5 * 1.10
# set up sensor types (thermistor is default)
# 1 = PII/Celeron Diode; 2 = 3904 transistor;
# 3435 = thermistor with Beta = 3435
# If temperature changes very little, try 1 or 2.
# set temp1_type 1
# set temp2_type 2
# set temp3_type 3435
# examples for temperature limits
# set temp1_max 40
# set temp1_max_hyst 37
# set temp2_max 52
# set temp2_max_hyst 47
chip "w83627thf-*" "w83637hf-*"
# Rather than an internal inverting op amp, the 627thf uses standard positive
# inputs and the negative voltages are level shifted by a 3.6V reference
# (same as 82d/83s).
# The math is convoluted, so we hope that your motherboard
# uses the recommended resistor values.
# Note that in1 (+12V) is the usual in4, and in4 (-12V) is the usual in5.
# Data sheet is obviously wrong for in4, the usual formula should work.
# No in5 nor in6.
label in0 "VCore"
label in1 "+12V"
label in2 "+3.3V"
label in3 "+5V"
label in4 "-12V"
label in7 "V5SB"
label in8 "VBat"
# Mori Hiroyuki reported to need this (P4P800)
# compute in0 @/2, @*2
compute in1 ((28/10)+1)*@, @/((28/10)+1)
compute in3 ((34/51)+1)*@, @/((34/51)+1)
compute in4 (5.14*@)-14.91, (@+14.91)/5.14
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)
# set limits to 5% for the critical voltages
# set limits to 10% for the non-critical voltages
# set limits to 20% for the battery voltage
# if your vid is wrong, you'll need to adjust in0_min and in0_max
# set in0_min cpu0_vid * 0.95
# set in0_max cpu0_vid * 1.05
# set in1_min 12 * 0.90
# set in1_max 12 * 1.10
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# set in3_min 5.0 * 0.95
# set in3_max 5.0 * 1.05
# set in4_min -12 * 1.10
# set in4_max -12 * 0.90
# set in7_min 5 * 0.95
# set in7_max 5 * 1.05
# set in8_min 3.0 * 0.80
# set in8_max 3.0 * 1.20
# set up sensor types (thermistor is default)
# 1 = PII/Celeron Diode; 2 = 3904 transistor;
# 3435 = thermistor with Beta = 3435
# If temperature changes very little, try 1 or 2.
# set temp1_type 1
# set temp2_type 2
# set temp3_type 3435
label temp1 "M/B Temp"
label temp2 "CPU Temp"
# ignore temp3
# examples for temperature limits
# set temp1_max 40
# set temp1_max_hyst 37
# set temp2_max 52
# set temp2_max_hyst 47
# set temp3_max 52
# set temp3_max_hyst 47
# ignore fan1
label fan2 "CPU Fan"
# ignore fan3
# Here are configurations for Winbond W83792AD/D chip.
chip "w83792d-*"
label in0 "VCoreA"
label in1 "VCoreB"
label in6 "5VCC"
label in7 "5VSB"
label in8 "VBAT"
# set in0_min 1.4
# set in0_max 1.6
# set in1_min 1.4
# set in1_max 1.6
# set in2_min 3.2
# set in2_max 3.4
# set in3_min 3.1
# set in3_max 3.3
# set in4_min 1.4
# set in4_max 1.5
# set in5_min 2.6
# set in5_max 2.65
# set in6_min 5 * 0.95
# set in6_max 5 * 1.05
# set in7_min 5 * 0.95
# set in7_max 5 * 1.05
# set in8_min 3 * 0.95
# set in8_max 3 * 1.05
# fan1 adjustments examples
# set fan1_div 4
# set fan1_min 1500
# temp2 limits examples
# set temp2_max 42
# set temp2_max_hyst 37
# ignore examples
# ignore fan7
# ignore temp3
# Here are configurations for Winbond W83793 chip.
chip "w83793-*"
label in0 "VCoreA"
label in1 "VCoreB"
label in2 "Vtt"
label in5 "+3.3V"
label in6 "+12V"
label in7 "+5V"
label in8 "5VSB"
label in9 "VBAT"
compute in6 12*@ , @/12
label temp1 "CPU1 Temp"
label temp2 "CPU2 Temp"
# fan1 adjustments examples
# set fan1_min 1500
# temp2 limits examples
# set temp2_max 45
# set temp2_max_hyst 40
# ignore examples
# ignore fan7
# ignore temp3
chip "as99127f-*"
# Asus won't release a datasheet so this is guesswork.
# Thanks to Guntram Blohm, Jack, Ed Harrison, Artur Gawryszczak,
# Victor G. Marimon and others for their feedback.
# Dual power plane
label in0 "VCore 1"
label in1 "VCore 2"
# Single power plane (A7V133, A7M266, CUV4X)
# label in0 "VCore"
# ignore in1
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
# These last two may not make sense on all motherboards.
label in5 "-12V"
label in6 "-5V"
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((28/10)+1)*@ , @/((28/10)+1)
# AS99127F rev.1 (same as w83781d)
compute in5 -(240/60.4)*@ , -@/(240/60.4)
compute in6 -(90.9/60.4)*@ , -@/(90.9/60.4)
# AS99127F rev.2 (same as w83782d)
# compute in5 (5.14 * @) - 14.91 , (@ + 14.91) / 5.14
# compute in6 (3.14 * @) - 7.71 , (@ + 7.71) / 3.14
# Depending on your motherboard, you may have to use any of two formulae
# for temp2. Quoting Artur Gawryszczak (edited to reflect subsequent fixes
# to the driver):
# "I guess, that the formula "(@*15/43)+25, (@-25)*43/15" is correct
# for those Asus motherboards, which get CPU temperature from internal
# thermal diode (Pentium Coppermine, and above), while no formula is needed
# for Athlon/Duron boards, which use a thermistor in the socket."
# An alternative formula was then found and reported by Victor G. Marimon.
# Asus A7V133, Asus A7M266
# No compute line is needed
# Asus CUV4X, Asus A7V8X
# compute temp2 (@*15/43)+25, (@-25)*43/15
# Asus CUSL2, Asus CUV266-DLS, Asus TUSL2-C
# compute temp2 (@*30/43)+25, (@-25)*43/30
# See comments above if temp3 looks bad. What works for temp2 is likely
# to work for temp3 for dual-CPU boards, such as the CUV4X-D.
# Most Asus boards have temperatures settled like that:
label temp1 "M/B Temp"
label temp2 "CPU Temp"
# However, some boards have them swapped (A7N8X Deluxe rev.2,
# A7N8X-E Deluxe rev.2, CUV4X):
# label temp1 "CPU Temp"
# label temp2 "M/B Temp"
# Most boards have no temp3 by default, except for dual-CPU boards.
# label temp3 "CPU 2 Temp"
# ignore temp3
# set limits to 5% for the critical voltages
# set limits to 10% for the non-critical voltages
# set limits to 20% for the battery voltage
# set in0_min cpu0_vid*0.95
# set in0_max cpu0_vid*1.05
# set in1_min cpu0_vid*0.95
# set in1_max cpu0_vid*1.05
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# set in3_min 5.0 * 0.95
# set in3_max 5.0 * 1.05
# set in4_min 12 * 0.90
# set in4_max 12 * 1.10
# set in5_min -12 * 0.90
# set in5_max -12 * 1.10
# set in6_min -5 * 0.95
# set in6_max -5 * 1.05
# examples for temperature limits
# set temp1_max 40
# set temp1_max_hyst 37
# set temp2_max 52
# set temp2_max_hyst 47
# set temp3_max 52
# set temp3_max_hyst 47
chip "gl518sm-*"
# IMPORTANT: in0, in1, and in2 values (+5, +3, and +12) CANNOT be read
#
# Factors and labels taken from GL518SM datasheet, they seem to give
# reasonable values with EISCA connected Fan78
label in0 "+5V"
label in1 "+3.3V"
label in2 "+12V"
label in3 "Vcore"
# in2 depends on external resistors (4,7k and 15k assumed here)
# in1 and in3 require no scaling
compute in2 (197/47)*@ , @/(197/47)
# set in0_min 4.8
# set in0_max 5.2
# set in1_min 3.20
# set in1_max 3.40
# set in2_min 11.0
# set in2_max 13.0
# set in3_min 2.10
# set in3_max 2.30
# set fan2_min 0
chip "gl520sm-*"
# Factors and labels taken from GL520SM datasheet
# The GL520SM has two application modes. In mode 1 it has two thermistor
# inputs, in mode 2 it has only one and an extra (negative) voltage input.
# The mode is supposed to be set properly by your BIOS so you should not
# need to change it. Note that you have either temp2 or in4, not both.
label in0 "+5V"
label in1 "+3.3V"
label in2 "+12V"
label in3 "Vcore"
label in4 "-12V"
# in1 and in3 require no scaling
# in2 depends on external resistors (4,7k and 15k assumed)
# in4 = ((R1+R2)/R2)*@ - (R1/R2)*vdd
#
# -12 --| R1 |---t---| R2 |-- +5
# |
# vin4
#
compute in2 (197/47)*@ , @/(197/47)
compute in4 (5*@)-(4*in0_input) , (@+4*in0_input)/5
# set in0_min 4.8
# set in0_max 5.2
# set in1_min 3.20
# set in1_max 3.40
# set in2_min 11.0
# set in2_max 13.0
# set in3_min 2.10
# set in3_max 2.30
chip "lm80-*"
# The values below should be correct if you own a qdi BX (brilliant1)
# mainboard. Many thanks go to Peter T. Breuer for helping us figure
# out how to handle the LM80.
# For positive voltages (in0..in4), two resistors are used, with the following
# formula (R1,R2: resistor values, Vs: read voltage, Vin: pin voltage)
# R1 = R2 * (Vs/Vin - 1)
# For negative voltages (in5, in6) two resistors are used, with the following
# formula (R3,R4: resistor values, Vs: read voltage, Vin: pin voltage,
# V5: +5V)
# R3 = R4 * (Vs - Vin) / (Vin - V5)
# Here are the official LM80 data sheet values.
# Vs R1,R3 R2,R4 Vin
# +2.5V 23.7 75 +1.9
# +3.3V 22.1 30 +1.9
# +5.0 24 14.7 +1.9
# +12.0 160 30.1 +1.9
# -12.0 160 35.7 +1.9
# -5.0 36 16.2 +1.9
# Now curiously enough, VCore is connected with (unknown) resistors, which
# translate a +2.8V to +1.9V. So we use that in the computations below.
label in0 "+5V"
label in1 "VTT"
label in2 "+3.3V"
label in3 "+Vcore"
label in4 "+12V"
label in5 "-12V"
label in6 "-5V"
compute in0 (24/14.7 + 1) * @ , @ / (24/14.7 + 1)
compute in2 (22.1/30 + 1) * @ , @ / (22.1/30 + 1)
compute in3 (2.8/1.9) * @, @ * 1.9/2.8
compute in4 (160/30.1 + 1) * @, @ / (160/30.1 + 1)
compute in5 (160/35.7)*(@ - in0_input) + @, (@ + in0_input * 160/35.7)/ (1 + 160/35.7)
compute in6 (36/16.2)*(@ - in0_input) + @, (@ + in0_input * 36/16.2) / (1 + 36/16.2)
# set in0_min 5 * 0.95
# set in0_max 5 * 1.05
# What is your VTT? It is probably not this value...
# set in1_min 2*0.95
# set in1_max 2*1.05
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# What is your VCore? It is probably not this value...
# set in3_min 1.9 * 0.95
# set in3_max 1.9 * 1.05
# set in4_min 12 * 0.95
# set in4_max 12 * 1.05
# set in5_min -12 * 1.05
# set in5_max -12 * 0.95
# set in6_min -5 * 1.05
# set in6_max -5 * 0.95
# All 4 of these limits apply to the single temperature sensor.
# "crit" may or may not do anything on your motherboard but it should
# be set higher than the "max" thresholds.
# set temp1_max_hyst 45
# set temp1_max 52
# set temp1_crit_hyst 57
# set temp1_crit 62
chip "via686a-*"
# VIA is very specific about the voltage sensor inputs, and our labels
# reflect what they say. Unfortunately, they are not at all specific about
# how to convert any of the register values to real units. Fortunately,
# Jonathan Yew and Alex van Kaam came through with some data for temp
# conversion and formulae for voltage conversion. However, the conversions
# should be regarded as our best guess - YMMV.
# On the Tyan S1598, the 2.5V sensor reads 0 and is not displayed in the BIOS.
# Linas Vepstas reports that this sensor shows nothing of
# interest on the Abit KA7 (Athlon), and is also not displayed in the BIOS.
# Likewise, Johannes Drechsel-Burkhard reports that this
# sensor is unavailable in the BIOS of his MSI K7T Pro (Thunderbird). So,
# if you have one of these boards you may want to uncomment the 'ignore in1'
# line below.
label in0 "CPU core"
label in1 "+2.5V"
#ignore in1
label in2 "I/O"
label in3 "+5V"
label in4 "+12V"
label fan1 "CPU Fan"
label fan2 "P/S Fan"
# VIA suggests that temp3 is an internal temp sensor for the 686a. However,
# on the Tyan S1598 as well as the Abit KA7 (Athalon), the absolute values
# of the readings from that sensor are not valid. The readings do seem to
# correlate with temp changes, but the conversion factor may be quite
# different from temp1 & temp2 (as noted above, VIA has not provided
# conversion info). So, you may wish to 'ignore temp3'.
# Johannes Drechsel-Burkhard notes that on his MSI K7T Pro,
# temp1 is the CPU temp and temp2 is the SYS temp. Hugo van der Merwe notes
# the same for his Gigabyte GA-7DXC, Olivier Martin for his Gigabyte
# GA-7ZM and Patrick Thomson for his Chaintech CT-5ATA.
# Thomas Anglmaier notes: on Epox EP-7kxa temp2 is CPU and temp1 is SYS.
label temp1 "SYS Temp"
label temp2 "CPU Temp"
label temp3 "SBr Temp"
#ignore temp3
# Set your CPU core limits here if the BIOS did not.
#set in0_min 1.70 * 0.95
#set in0_max 1.70 * 1.05
# Other voltage values are standard so we can enforce the limits.
# set in1_min 2.5 * 0.95
# set in1_max 2.5 * 1.05
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# set in3_min 5 * 0.9
# set in3_max 5 * 1.1
# set in4_min 12 * 0.9
# set in4_max 12 * 1.1
# Set your temp limits here. Remember, 'tempX_max' is the temp at which an
# alarm is triggered, and 'tempX_max_hyst' is the temp at which an alarm turns off.
# Setting tempX_max_hyst to a few degrees below the corresponding tempX_max
# prevents an oscillation between alarm on and off states. This kind of
# oscillation is known as hyteresis, thus the name. (You typically get the
# most serious and troublesome hysteresis when a sensor triggers something to
# reduce the temp, thus creating a negative feedback loop. Even without that,
# we would still get some oscillation when the temp hovers around the limit
# due to noise.)
# set temp1_max_hyst 40
# set temp1_max 45
# set temp2_max_hyst 55
# set temp2_max 60
# set temp3_max_hyst 60
# set temp3_max 65
# You could set your fan limits too, but the defaults should be fine.
#set fan1_min 5000
#set fan2_min 5000
chip "adm1025-*" "ne1619-*"
# The ADM1025 has integrated scaling resistors, rather
# than external resistors common to most sensor devices.
# These apply to the 6 voltage inputs in0-in5 (+2.5V, VCore,
# +3.3V, +5V, +12V, VCC). As the scaling is fixed inside
# the chip for these inputs, it is fairly certain that the
# motherboard connections match these labels, and that the
# driver computations are correct. Therefore they do not need to
# be overridden here.
label in0 "+2.5V"
label in1 "VCore"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
label in5 "VCC"
# Tolerate a 5% deviance for CPU power-supply
# set in1_min cpu0_vid * 0.95
# set in1_max cpu0_vid * 1.05
# Tolerate a 10% deviance for other voltages
# set in0_min 2.5 * 0.90
# set in0_max 2.5 * 1.10
# set in2_min 3.3 * 0.90
# set in2_max 3.3 * 1.10
# set in3_min 5.0 * 0.90
# set in3_max 5.0 * 1.10
# set in4_min 12 * 0.90
# set in4_max 12 * 1.10
# set in5_min 3.3 * 0.90
# set in5_max 3.3 * 1.10
# Depending on how your chipset is hardwired, you may or may not have
# +12V readings (will show as 0.0V if you don't have it).
# ignore in4
# VCC is the power-supply voltage of the ADM1025 chipset, generally
# redundant with +3.3V so you may want to hide it.
# ignore in5
# Temperatures
label temp1 "CPU Temp"
label temp2 "M/B Temp"
# set temp1_min 10
# set temp1_max 60
# set temp2_min 10
# set temp2_max 45
chip "lm87-*" "adm1024-*"
#
# The LM87 has integrated scaling resistors, rather
# than external resistors common to most sensor devices.
# These apply to the first 6 voltage inputs in0-in5
# (+2.5, Vccp1, +3.3, +5, 12, +Vccp2). As the scaling is fixed inside
# the chip for these inputs, it is fairly certain that the
# motherboard connections match these labels, and that the
# driver computations are correct. Therefore they do not need to
# be overridden here.
label in0 "+2.5V"
label in1 "VCore"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
# label in5 "VCore2"
label fan1 "CPU Fan"
# label fan2 "Case Fan"
label temp1 "M/B Temp"
label temp2 "CPU Temp"
# label temp3 "AUX Temp"
# set in1_min cpu0_vid * 0.95
# set in1_max cpu0_vid * 1.05
# set in2_min 3.3 * 0.92
# set in2_max 3.3 * 1.08
# set in3_min 5 * 0.92
# set in3_max 5 * 1.08
# set in4_min 12 * 0.90
# set in4_max 12 * 1.10
# These ones are mutually exclusive with temp3. If you have temp3,
# comment out these lines as they will trigger errors on "sensors -s".
# set in0_min 2.5 * 0.92
# set in0_max 2.5 * 1.08
# set in5_min cpu0_vid * 0.95
# set in5_max cpu0_vid * 1.05
# Increase fan clock dividers if your fans read 0 RPM while you know
# they are connected and running.
# set fan1_div 4
# set fan2_div 4
# set fan1_min 3000
# set fan2_min 3000
# set temp1_min 5
# set temp1_max 65
# set temp2_min 5
# set temp2_max 70
# Uncomment if you actually have temp3 (which means you don't have 2.5V
# nor Vccp2, as they are mutually exclusive).
# set temp3_min 5
# set temp3_max 70
# LM87 AIN1 and AIN2 Section
# -12 and -5 may be reversed on your board, this is
# just a guess, the datasheet gives no guidance.
# label in6 "-12V"
# label in7 "-5V"
# compute in6 (7.50 * @) - 21.45 , (@ + 21.45) / 7.50
# compute in7 (4.05 * @) - 10.07 , (@ + 10.07) / 4.05
# set in6_min -12 * 0.95
# set in7_min -5 * 0.95
# set in6_max -12 * 1.05
# set in7_max -5 * 1.05
chip "it87-*" "it8712-*"
# The values below have been tested on Asus CUSI, CUM motherboards.
# Voltage monitors as advised in the It8705 data sheet
label in0 "VCore 1"
label in1 "VCore 2"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
label in5 "-12V"
label in6 "-5V"
label in7 "Stdby"
label in8 "VBat"
# Incubus Saturnus reports that the IT87 chip on Asus A7V8X-X seems
# to report the VCORE voltage approximately 0.05V higher than the board's
# BIOS does. Although it doesn't make much sense physically, uncommenting
# the next line should bring the readings in line with the BIOS' ones in
# this case.
# compute in0 -0.05+@ , @+0.05
# If 3.3V reads around 1.65V, uncomment the following line:
# compute in2 2*@ , @/2
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
# A number of Gigabyte boards (GA-8IPE1000Pro, GA-8KNXP, GA-7N400-L) use
# a different resistor combination for +5V:
# compute in3 ((10/10)+1)*@ , @/((10/10)+1)
compute in4 ((30/10) +1)*@ , @/((30/10) +1)
# For this family of chips the negative voltage equation is different from
# the lm78. The chip uses two external resistor for scaling but one is
# tied to a positive reference voltage. See ITE8705/12 datasheet (SIS950
# data sheet is wrong)
# Vs = (1 + Rin/Rf) * Vin - (Rin/Rf) * Vref.
# Vref = 4.096 volts, Vin is voltage measured, Vs is actual voltage.
# The next two are negative voltages (-12 and -5).
# The following formulas must be used. Unfortunately the datasheet
# does not give recommendations for Rin, Rf, but we can back into
# them based on a nominal +2V input to the chip, together with a 4.096V Vref.
# Formula:
# actual V = (Vmeasured * (1 + Rin/Rf)) - (Vref * (Rin/Rf))
# For -12V input use Rin/Rf = 6.68
# For -5V input use Rin/Rf = 3.33
# Then you can convert the forumula to a standard form like:
compute in5 (7.67 * @) - 27.36 , (@ + 27.36) / 7.67
compute in6 (4.33 * @) - 13.64 , (@ + 13.64) / 4.33
#
# this much simpler version is reported to work for a
# Elite Group K7S5A board
#
# compute in5 -(36/10)*@, -@/(36/10)
# compute in6 -(56/10)*@, -@/(56/10)
#
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)
# set in0_min 1.5 * 0.95
# set in0_max 1.5 * 1.05
# set in1_min 2.4
# set in1_max 2.6
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# set in3_min 5.0 * 0.95
# set in3_max 5.0 * 1.05
# set in4_min 12 * 0.95
# set in4_max 12 * 1.05
# set in5_max -12 * 0.95
# set in5_min -12 * 1.05
# set in6_max -5 * 0.95
# set in6_min -5 * 1.05
# set in7_min 5 * 0.95
# set in7_max 5 * 1.05
#the chip does not support in8 min/max
# Temperature
#
# Important - if your temperature readings are completely whacky
# you probably need to change the sensor type.
# Adujst and uncomment the appropriate lines below.
#
# 2 = thermistor; 3 = thermal diode; 0 = unused
# set temp1_type 3
# set temp2_type 3
# set temp3_type 3
# If a given sensor isn't used, you will probably want to ignore it
# (see ignore statement right below).
label temp1 "M/B Temp"
# set temp1_max 40
# set temp1_min 15
label temp2 "CPU Temp"
# set temp2_max 45
# set temp2_min 15
# ignore temp3
# set temp3_max 45
# set temp3_min 15
# The A7V8X-X has temperatures inverted, and needs a conversion for
# CPU temp. Thanks to Preben Randhol for the formula.
# label temp1 "CPU Temp"
# label temp2 "M/B Temp"
# compute temp1 (-15.096+1.4893*@), (@+15.096)/1.4893
# The A7V600 also has temperatures inverted, and needs a different
# conversion for CPU temp. Thanks to Dariusz Jaszkowski for the formula.
# label temp1 "CPU Temp"
# label temp2 "M/B Temp"
# compute temp1 (@+128)/3, (3*@-128)
# Fans
# set fan1_min 0
# set fan2_min 3000
# ignore fan3
# set fan3_min 3000
chip "it8716-*"
# Voltages
label in0 "VCore"
label in1 "VDDR"
label in2 "+3.3V" # VCC3
label in3 "+5V" # VCC
label in4 "+12V"
# label in5 "-12V"
# label in6 "-5V"
label in7 "5VSB" # VCCH
label in8 "VBat"
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((30/10)+1)*@ , @/((30/10)+1)
# compute in5 (1+232/56)*@ - 4.096*232/56 , (@ + 4.096*232/56)/(1+232/56)
# compute in6 (1+120/56)*@ - 4.096*120/56 , (@ + 4.096*120/56)/(1+120/56)
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)
# If vid (nominal CPU voltage) isn't correct, hardcode the correct value
# instead.
# set in0_min cpu0_vid * 0.95
# set in0_max cpu0_vid * 1.05
# set in1_min 1.8 * 0.95
# set in1_max 1.8 * 1.05
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# set in3_min 5 * 0.95
# set in3_max 5 * 1.05
# set in4_min 12 * 0.95
# set in4_max 12 * 1.05
# set in5_max -12 * 0.95
# set in5_min -12 * 1.05
# set in6_max -5 * 0.95
# set in6_min -5 * 1.05
# set in7_min 5 * 0.95
# set in7_max 5 * 1.05
# The chip does not support in8 min/max
# Temperatures
# If you are lucky, the BIOS has set the proper sensor types for you.
# If your temperature readings are completely whacky you probably
# need to change the sensor types. Adujst and uncomment the
# appropriate lines below.
#
# 2 = thermistor; 3 = thermal diode; 0 = unused
# set temp1_type 3
# set temp2_type 3
# set temp3_type 3
# If a given sensor isn't used, you will probably want to ignore it
# as well (see ignore statement right below).
# The CPU sensor can be any of temp1, temp2 or temp3 - it's motherboard
# dependent. Same for the motherboard temperature.
# label temp1 "CPU Temp"
# label temp2 "M/B Temp"
# ignore temp3
# set temp1_max 60
# set temp1_min 10
# set temp2_max 50
# set temp2_min 10
# Fans
# The CPU fan can be any of fan1, fan2 or fan3 - it's motherboard
# dependent. Same for the case fan.
# label fan1 "CPU Fan"
# label fan2 "Case Fan"
# ignore fan3
# set fan1_min 2000
# set fan2_min 2000
chip "fscpos-*"
# Fujitsu-Siemens Poseidon chip
# Temperature
label temp1 "CPU Temp"
label temp2 "M/B Temp"
label temp3 "Aux Temp"
# Fans
# Voltage
label in0 "+12V"
label in1 "+5V"
label in2 "Battery"
chip "fscscy-*"
# Fujitsu-Siemens Scylla chip
# Temperature
label temp1 "CPU0 Temp"
label temp2 "CPU1 Temp"
label temp3 "M/B Temp"
label temp4 "Aux Temp"
# Fans
label fan1 "CPU Fan"
label fan2 "CPU Fan"
# Voltage
label in0 "+12V"
label in1 "+5V"
label in2 "+3.3V"
chip "fscher-*"
# Fujitsu-Siemens Hermes chip
# Temperature
label temp1 "CPU Temp"
label temp2 "M/B Temp"
label temp3 "Aux Temp"
# Fans
label fan1 "PSU Fan"
label fan2 "CPU Fan"
label fan3 "Aux Fan"
# Voltage
label in0 "+12V"
label in1 "+5V"
label in2 "Battery"
# Uncomment the computes line below when using the old fscher driver, leave
# them commented when using the newer unified fschmd driver
#
# M R O O M R
# compute in0 (@ * (49 * 33) / 255) + (0 / 100), (@ - (0 / 100)) * 255 / (49 * 33)
# compute in1 (@ * (20 * 33) / 255) + (0 / 100), (@ - (0 / 100)) * 255 / (20 * 33)
# compute in2 (@ * (10 * 33) / 255) + (0 / 100), (@ - (0 / 100)) * 255 / (10 * 33)
chip "pcf8591-*"
#
# values for the Philips PCF8591 chip
#
# Analog inputs
# You may discard ch2 and ch3 if you don't use them (depends on the input
# configuration)
# ignore in2
# ignore in3
label in0 "Chan. 0"
label in1 "Chan. 1"
label in2 "Chan. 2"
label in3 "Chan. 3"
# The driver assumes Vref = 2.56V and Agnd = 0V. If it doesn't match
# your hardware, you have to use compute lines. The example below is
# correct for Vref = 5.0V and Agnd = 0V.
# compute in0 (@ * 500 / 256), (@ * 256 / 500)
# compute in1 (@ * 500 / 256), (@ * 256 / 500)
# compute in2 (@ * 500 / 256), (@ * 256 / 500)
# compute in3 (@ * 500 / 256), (@ * 256 / 500)
chip "adm1021-*" "adm1023-*" "max1617-*" "max1617a-*" "thmc10-*" "lm84-*" "gl523sm-*" "mc1066-*"
label temp1 "Board Temp"
label temp2 "CPU Temp"
# set temp1_min 40
# set temp1_max 70
# set temp2_min 40
# set temp2_max 70
chip "lm83-*"
label temp1 "M/B Temp"
label temp2 "D1 Temp"
label temp3 "CPU Temp"
label temp4 "D3 Temp"
# ignore D1 and/or D3 readings if not used
# ignore temp2
# ignore temp4
# change high limits to fit your needs
# set temp1_max 55
# set temp2_max 60
# set temp3_max 65
# set temp4_max 60
# change critical limit to fit your needs
# only one limit for all four temperatures
# should be higher than each of the high limits above
# set temp3_crit 85
chip "max1619-*"
label temp1 "M/B Temp"
label temp2 "CPU Temp"
# change high and low limits to fit your needs
# set temp2_min 10
# set temp2_max 100
# change critical limit and hysteresis to fit your needs
# set temp2_crit 50
# set temp2_crit_hyst 40
chip "lm90-*" "adm1032-*" "lm86-*" "max6657-*" "adt7461-*" "max6680-*" "w83l771-*"
label temp1 "M/B Temp"
label temp2 "CPU Temp"
# change high and low limits to fit your needs
# set temp1_min 10
# set temp1_max 55
# set temp2_min 10
# set temp2_max 66
# change critical limits to fit your needs
# should be higher than the corresponding high limit above
# set temp1_crit 75
# set temp2_crit 85
# change the hysteresis values (to critical limits) to fit your needs
# note #1: hyst2 will be automatically set with the same delta
# note #2: the internal register, which stores a single, relative value
# for both channels, cannot hold values greater than 31, so the delta
# between critical temperatures and respective absolute hysteresis can
# never exceed this value
# set temp1_crit_hyst 70
chip "lm89-*" "lm99-*"
label temp1 "G/C Temp"
label temp2 "GPU Temp"
# note #1: the LM99 needs the compute statement below if you're running
# a kernel <= 2.6.27; since kernel 2.6.28 the offset is handled in the
# lm90 driver directly instead
# note #2: there is no way for us to differentiate between a LM89 and a
# LM99; you have to know what you have; the driver will assume a LM99,
# use the force_lm86 module parameter if you have a LM89
# compute temp2 @+16, @-16
# change high and low limits to fit your needs
# set temp1_min 10
# set temp1_max 90
# set temp2_min 10
# set temp2_max 100
# change critical limits to fit your needs
# should be higher than the corresponding high limit above
# set temp1_crit 100
# set temp2_crit 110
# change the hysteresis values (to critical limits) to fit your needs
# note #1: hyst2 will be automatically set with the same delta
# note #2: the internal register, which stores a single, relative value
# for both channels, cannot hold values greater than 31, so the delta
# between critical temperatures and respective absolute hysteresis can
# never exceed this value
# set temp1_crit_hyst 105
chip "lm63-*"
label temp1 "M/B Temp"
label temp2 "CPU Temp"
label fan1 "CPU Fan"
# Change limits to fit your needs. Note that temp2_crit is read-only.
# set temp1_max 50
# set temp2_min 10
# set temp2_max 70
# set temp2_crit_hyst 75
# set fan1_min 2000
chip "vt1211-*"
label in0 "+3.3V"
label in1 "+2.5V"
label in2 "VCore"
label in3 "+5V"
label in4 "+12V"
label in5 "+3.3V"
label temp1 "CPU Temp"
label temp2 "Int Temp"
label fan1 "Case Fan"
label fan2 "CPU Fan"
# All voltage calculations have the form
# compute inX @ * (1 + R1 / R2), @ / (1 + R1 / R2)
#
# The following are the resistor values as recommended by VIA
# Voltage R1 R2
# ------- ---- ----
# VCore - - (no scaling)
# 3.3 6.8k 10k
# 2.5 2k 10k
# 5.0 14k 10k
# 12.0 47k 10k
#
# The VT1211 internal 3.3V (in5) is scaled by the driver and doesn't
# need to be adjusted here. VCore doesn't need scaling at all.
compute in0 @ * (1 + 6.8 / 10), @ / (1 + 6.8 / 10)
compute in1 @ * (1 + 2 / 10), @ / (1 + 2 / 10)
compute in3 @ * (1 + 14 / 10), @ / (1 + 14 / 10)
compute in4 @ * (1 + 47 / 10), @ / (1 + 47 / 10)
# set in0_min 3.3 * 0.95
# set in0_max 3.3 * 1.05
# set in1_min 2.5 * 0.95
# set in1_max 2.5 * 1.05
# If your vid is wrong, hardcode the CPU voltage (e.g. 1.4)
# set in2_min cpu0_vid * 0.97
# set in2_max cpu0_vid * 1.03
# set in3_min 5.0 * 0.95
# set in3_max 5.0 * 1.05
# set in4_min 12.0 * 0.90
# set in4_max 12.0 * 1.10
set in5_min 3.3 * 0.95
set in5_max 3.3 * 1.05
# The temperature calculations are of the form
# compute tempX (@ - Offset) / Gain, (@ * Gain) + Offset
#
# The following are the gain and offset values as recommended by VIA
# Diode Type Gain Offset
# ---------- ---- ------
# Intel CPU 0.9528 88.638
# 0.9686 65.000 *)
# VIA C3 Ezra 0.9528 83.869
# VIA C3 Ezra-T 0.9528 73.869
#
# *) These are the values from the previous sensors.conf. I don't know
# where they came from or how they got derived.
#
# The VT1211 internal temperature (temp2) is scaled by the driver
# and doesn't need to be adjusted here.
compute temp1 (@ - 73.869) / 0.9528, (@ * 0.9528) + 73.869
# The thermistor calculations are of the form
# compute tempX 1 / (1 / 298.15 - (` Vmax / @ - 1)) / B) - 273.15, \
# Vmax / (1 + (^ (B / 298.15 - B / (273.15 + @))))
#
# B is the thermistor beta value, Vmax is the reference voltage, '^' is the
# exp() operator and '`' is the ln() operator.
# Given B = 3435 and Vmax = 2.2V and assuming that the thermistor forms a
# resistor divider with a resistor equal to the thermistor's nominal value at
# 25 degrees C, the following compute lines can be used:
compute temp3 1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \
2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @))))
compute temp4 1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \
2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @))))
compute temp5 1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \
2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @))))
compute temp6 1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \
2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @))))
compute temp7 1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \
2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @))))
# set temp1_max_hyst 80
# set temp1_max 85
# set temp2_max_hyst 60
# set temp2_max 65
# set temp3_max_hyst 60
# set temp3_max 65
# set temp4_max_hyst 40
# set temp4_max 45
# set fan1_min 3000
# set fan2_min 3000
chip "vt8231-*"
label in1 "+2.5V"
label in2 "VCore"
label in3 "+5V"
label in4 "+12V"
label in5 "+3.3V"
label temp1 "CPU Temp"
label temp2 "M/B Temp"
# Here are the resistor values as recommended by VIA:
# Voltage R1 R2
# VCore no scaling
# 2.5 2k 10k
# 3.5 (3.3V ext.) 6.8k 10k
# 5.0 14k 10k
# 12.0 47k 10k
# compute in0 @ * (1 + 6.8 / 10), @ / (1 + 6.8 / 10)
compute in1 @ * (1 + 2 / 10), @ / (1 + 2 / 10)
compute in3 @ * (1 + 14 / 10), @ / (1 + 14 / 10)
compute in4 @ * (1 + 47 / 10), @ / (1 + 47 / 10)
# in5 is scaled internally so scaling is done by the driver.
# set in0_min 2.5 * 0.95
# set in0_max 2.5 * 1.05
# set in1_min 2.5 * 0.95
# set in1_max 2.5 * 1.05
# Replace "2.0" with your nominal CPU voltage for in2.
# set in2_min 2.0 * 0.95
# set in2_max 2.0 * 1.05
# set in3_min 5.0 * 0.95
# set in3_max 5.0 * 1.05
# set in4_min 12.0 * 0.95
# set in4_max 12.0 * 1.05
# set in5_min 3.3 * 0.95
# set in5_max 3.3 * 1.05
# For Intel CPU:
compute temp1 (@ - 65) / 0.9686, (@ * 0.9686) + 65
# For VIA EPIA CPU (provided by Roger Lucas):
# compute temp1 (@ - 45) / 0.7809, (@ * 0.7809) + 45
# Thermistor calculations
# 3435 is the thermistor beta, 2.2 is the reference voltage.
# '^' is the e**x operator; '`' is the ln(x) operator
# This assumes that the thermistor forms a resistor divider with a resistor
# equal to its nominal value at 25 degrees C.
compute temp2 1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \
2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @))))
compute temp3 1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \
2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @))))
# set temp1_max_hyst 60
# set temp1_max 65
# set temp2_max_hyst 40
# set temp2_max 45
# set fan1_min 3000
# set fan2_min 3000
chip "smsc47m1-*"
# SMSC LPC47M10x, LPC47M13x, LPC47M14x and LPC47B27x chips
# set fan1_min 3000
# set fan2_min 3000
chip "smsc47m192-*"
# Temperature and voltage input from SMSC LPC47M192 and LPC47M997 chips
# This example works on a Gigabyte K8U motherboard
# Voltages are scaled internally, no computations needed
label in0 "+2.5V"
# set in0_min 2.5 * 0.95
# set in0_max 2.5 * 1.05
label in1 "VCore"
# set in1_min cpu0_vid * 0.95
# set in1_max cpu0_vid * 1.05
label in2 "+3.3V"
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
label in3 "+5V"
# set in3_min 5.0 * 0.95
# set in3_max 5.0 * 1.05
label in4 "+12V"
# set in4_min 12.0 * 0.95
# set in4_max 12.0 * 1.05
label in5 "VCC"
# set in5_min 3.3 * 0.95
# set in5_max 3.3 * 1.05
label in6 "+1.5V"
# set in6_min 1.5 * 0.95
# set in6_max 1.5 * 1.05
# ignore in6
label in7 "+1.8V"
# set in7_min 1.8 * 0.95
# set in7_max 1.8 * 1.05
# Haven't yet heard from any board that has 1.8V connected, so
# this might be more appropriate:
# ignore in7
label temp1 "Chip Temp"
# set temp1_min 0
# set temp1_max 60
label temp2 "CPU Temp"
# set temp2_min 0
# set temp2_max 60
label temp3 "Sys Temp"
# set temp3_min 0
# set temp3_max 60
#
# This example was tested vs. Asus P4S333
#
chip "asb100-*"
label in0 "VCore 1"
#set in0_min cpu0_vid * 0.95
#set in0_max cpu0_vid * 1.05
label in1 "VCore 2"
ignore in1
#set in1_min cpu0_vid * 0.95
#set in1_max cpu0_vid * 1.05
label in2 "+3.3V"
#set in2_min 3.3 * 0.95
#set in2_max 3.3 * 1.05
label in3 "+5V"
compute in3 1.68 * @ , @ / 1.68
#set in3_min 5.0 * 0.95
#set in3_max 5.0 * 1.05
label in4 "+12V"
compute in4 3.8 * @ , @ / 3.8
#set in4_min 12 * 0.90
#set in4_max 12 * 1.10
label in5 "-12V (reserved)"
#ignore in5
compute in5 -@ * 3.97 , -@ / 3.97
#set in5_max -12 * 0.90
#set in5_min -12 * 1.10
label in6 "-5V (reserved)"
#ignore in6
compute in6 -@ * 1.666 , -@ / 1.666
#set in6_max -5 * 0.95
#set in6_min -5 * 1.05
label temp1 "M/B Temp"
#set temp1_max 45
#set temp1_max_hyst 40
label temp2 "CPU Temp (Intel)"
#ignore temp2
#set temp2_max 60
#set temp2_max_hyst 50
# PWRTMP connector on P4S333, for external sensor
label temp3 "Power Temp"
#ignore temp3
#set temp3_max 45
#set temp3_max_hyst 40
# Used for Athlon diode, ignore for P4S333
label temp4 "CPU Temp (AMD)"
#set temp4_max 60
#set temp4_max_hyst 50
#ignore temp4
label fan1 "CPU Fan"
#set fan1_div 4
#set fan1_min 2000
label fan2 "Chassis Fan"
#set fan2_div 2
#set fan2_min 4000
label fan3 "Power Fan"
#set fan3_div 2
#set fan3_min 4000
#
# Sample configuration for the Intel S845WD1-E
# courtesy of Marcus Schopen
#
chip "lm85-*" "lm85b-*" "lm85c-*" "adm1027-*" "adt7463-*" "adt7468-*" "emc6d100-*" "emc6d102-*"
# Voltage inputs
# Depending on the hardware setup, the ADT7463 and ADT7468 may not have in4.
label in0 "V1.5" # AGP on Intel S845WD1-E
label in1 "VCore"
label in2 "V3.3"
label in3 "V5"
label in4 "V12"
# Temperature inputs
label temp1 "CPU Temp"
label temp2 "Board Temp"
label temp3 "Remote Temp"
# Fan inputs
label fan1 "CPU Fan"
# Voltage scaling is done on-chip. No 'compute' directive
# should be necessary. If in0 has external scaling set
# it here.
# compute in0 @ * 2.5, @ / 2.5
# Adjust fans speeds for actual pulses per rev
# compute fan1 @ * 2, @ / 2 # 1 pulse per rev
# compute fan2 @ / 2, @ * 2 # 4 pulse per rev
# Ignore fans you (or your motherboard) don't have
# ignore fan2
# ignore fan3
# ignore fan4
# Set voltage limits
# set in0_min 1.5 * 0.95
# set in0_max 1.5 * 1.05
# set in1_min cpu0_vid * 0.95
# set in1_max cpu0_vid * 1.05
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# set in3_min 5.0 * 0.95
# set in3_max 5.0 * 1.05
# set in4_min 12 * 0.95
# set in4_max 12 * 1.05
# Set Fan limits
# set fan1_min 4000
# Set Temp Limits
# set temp1_min 10
# set temp1_max 50
# set temp2_min 10
# set temp2_max 35
# set temp3_min 10
# set temp3_max 35
chip "pc87365-*" "pc87366-*"
# Voltage inputs
label in7 "Vsb"
label in8 "Vdd"
label in9 "Vbat"
label in10 "AVdd"
compute in7 @*2, @/2
compute in8 @*2, @/2
compute in10 @*2, @/2
# These are the operating conditions as recommended by National
# Semiconductor
set in7_min 3.0
set in7_max 3.6
set in8_min 3.0
set in8_max 3.6
# set in9_min 2.4
# set in9_max 3.6
set in10_min 3.0
set in10_max 3.6
# Temperature inputs
label temp1 "CPU0 Temp"
label temp2 "CPU1 Temp"
label temp3 "S-IO Temp"
# set temp1_min 0
# set temp1_max 70
# set temp1_crit 85
# set temp2_min 0
# set temp2_max 70
# set temp2_crit 85
# set temp3_min 0
# set temp3_max 70
# set temp3_crit 85
# Thermistors
# On some systems, thermistors are used instead of thermal diodes.
# Note that these are the same pins used differently, so you really
# can't have them all on a given system.
# ignore temp1
# ignore temp2
ignore temp4
ignore temp5
ignore temp6
# 3435 is the thermistor beta.
# This assumes that the thermistor forms a resistor divider with a resistor
# equal to its nominal value at 25 degres Celsius. If not, change the values.
# We also assume that you have a working in10 (which is forcibly enabled by
# default). If not, use 3.3 instead, but you lose accuracy.
compute temp4 3435 / (` (1 / (1 - @ / in10_input) - 1) + 3435 / 298.15) - 273.15, \
in10_input * (1 - 1 / (1 + (^ (3435 / (273.15 + @) - 3435 / 298.15))))
compute temp5 3435 / (` (1 / (1 - @ / in10_input) - 1) + 3435 / 298.15) - 273.15, \
in10_input * (1 - 1 / (1 + (^ (3435 / (273.15 + @) - 3435 / 298.15))))
compute temp6 3435 / (` (1 / (1 - @ / in10_input) - 1) + 3435 / 298.15) - 273.15, \
in10_input * (1 - 1 / (1 + (^ (3435 / (273.15 + @) - 3435 / 298.15))))
# set temp4_min 0
# set temp4_max 70
# set temp4_crit 85
# set temp5_min 0
# set temp5_max 70
# set temp5_crit 85
# set temp6_min 0
# set temp6_max 70
# set temp6_crit 85
# Fan inputs
# Ignore fans you don't have
# ignore fan2
# ignore fan3
# set fan1_min 2000
# set fan2_min 2000
# set fan3_min 2000
chip "adm1030-*"
label temp1 "SYS Temp"
label temp2 "CPU Temp"
# set temp1_max 60
# set temp2_max 70
# set temp1_crit 85
# set temp2_crit 85
label fan1 "CPU Fan"
# set fan1_min 2000
chip "adm1031-*"
label temp1 "SYS Temp"
label temp2 "CPU Temp"
label temp3 "AUX Temp"
# set temp1_max 60
# set temp2_max 70
# set temp3_max 70
# set temp1_crit 85
# set temp2_crit 85
# set temp3_crit 85
label fan1 "CPU Fan"
label fan2 "Case Fan"
# set fan1_min 2000
# set fan2_min 2000
chip "w83l785ts-*"
label temp1 "CPU Diode"
chip "lm92-*"
label temp1 "CPU Temp"
# Change limits as you see fit
# set temp1_min 14
# set temp1_max 60
# set temp1_crit 72
# Hysteresis is computed from critical limit
# The same relative hysteresis is used for all of low, high
# and critical limits.
# set temp1_crit_hyst 70
# Winbond W83627EHF configuration originally contributed by Leon Moonen
# This is for an Asus P5P800, voltages for A8V-E SE.
chip "w83627ehf-*" "w83627dhg-*"
label in0 "VCore"
label in1 "+12V"
label in2 "AVCC"
label in3 "3VCC"
label in6 "+5V"
label in7 "VSB"
label in8 "VBAT"
# +12V is in1 and +5V is in6 as recommended by datasheet
compute in1 @*(1+(56/10)), @/(1+(56/10))
compute in6 @*(1+(22/10)), @/(1+(22/10))
# set in1_min 12.0*0.9
# set in1_max 12.0*1.1
# set in6_min 5.0*0.95
# set in6_max 5.0*1.05
# Set the 3.3V
# set in2_min 3.3*0.95
# set in2_max 3.3*1.05
# set in3_min 3.3*0.95
# set in3_max 3.3*1.05
# set in7_min 3.3*0.95
# set in7_max 3.3*1.05
# set in8_min 3.3*0.95
# set in8_max 3.3*1.05
# Fans
label fan1 "Case Fan"
label fan2 "CPU Fan"
label fan3 "Aux Fan"
# ignore fan3
# ignore fan4
# set fan1_min 1200
# set fan2_min 1700
# Temperatures
label temp1 "Sys Temp"
label temp2 "CPU Temp"
label temp3 "AUX Temp"
# ignore temp3
# set temp1_max 45
# set temp1_max_hyst 40
# set temp2_max 45
# set temp2_max_hyst 40
# Fintek F71805F/FG configuration
# This is the recommended wiring and resistor values from the F71805F/FG
# datasheet. Your motherboard manufacturer may or may not have followed
# these.
chip "f71805f-*" "f71872f-*"
# Voltages
label in0 "+3.3V"
label in1 "Vtt1.2V"
label in2 "Vram"
label in3 "Vchip"
label in4 "+5V"
label in5 "+12V"
label in6 "Vcc1.5V"
label in7 "Vcore"
label in8 "5VSB"
# in0 is scaled internally
compute in2 @*(1+100/100), @/(1+100/100)
compute in3 @*(1+100/47), @/(1+100/47)
compute in4 @*(1+200/47), @/(1+200/47)
compute in5 @*(1+200/20), @/(1+200/20)
compute in8 @*(1+200/47), @/(1+200/47)
# in0 is the chip's own VCC.
set in0_min 3.0
set in0_max 3.6
#set in1_min 1.2 * 0.95
#set in1_max 1.2 * 1.05
#set in2_min 2.5 * 0.95
#set in2_max 2.6 * 1.05
#set in3_min 3.3 * 0.95
#set in3_max 3.3 * 1.05
#set in4_min 5.0 * 0.95
#set in4_max 5.0 * 1.05
#set in5_min 12.0 * 0.95
#set in5_max 12.0 * 1.05
#set in6_min 1.5 * 0.95
#set in6_max 1.5 * 1.05
# in7 nominal value depends on the CPU model
#set in7_min 1.4 * 0.95
#set in7_max 1.4 * 1.05
#set in8_min 5.0 * 0.95
#set in8_max 5.0 * 1.05
# Fans
label fan1 "CPU Fan"
label fan2 "Sys Fan"
label fan3 "Aux Fan"
#set fan1_min 2100
#set fan2_min 1400
#set fan3_min 1400
# Temperatures
label temp1 "CPU Temp"
label temp2 "Sys Temp"
label temp3 "Aux Temp"
#set temp1_max 60
#set temp1_max_hyst 58
#set temp2_max 50
#set temp2_max_hyst 48
#set temp3_max 50
#set temp3_max_hyst 48
# Abit Uguru sensor part configuration.
# The Abit Uguru is relativly straight forward to configure.
# label statements:
# The voltage (in) temp and fan sensors are usualy in the same order as listed
# in the BIOS, but not always!
# compute statements:
# The temp and fan sensors don't need any compute statements. Most voltage
# inputs are directly connected to the IC and thus don't need an compute line
# because the 0-3494 mV voltage given by the kernel driver is correct. The sen-
# sors for higher voltages however are connect through a divider and measure
# ranges of: 0-4361mV, 0-6248mV or 0-14510mV. Thus the measured voltages must
# be multiplied by resp. 1.248, 1.788 or 4.153. 3.3 volt sources use the 1.248
# mutiplier, 5 volt the 1.788 and 12 volt the 4.153.
# set statements:
# The Abit BIOS sets reasonable treshholds and allows changing them, thus
# set statements may be ommited. The abituguru kernel driver does support
# them if you want to add them.
#
# The configuration below is for the Kv8Pro and AV8 this is the default as this
# driver is developed and tested on a Kv8Pro.
# Configurations for many other Abit boards can be found at:
# http://www.lm-sensors.org/trac/wiki/Configurations/Abit
# If your motherboard isn't listed there and you create a configuration for it
# please add it there.
chip "abituguru-*"
label in0 "CPU Core Voltage"
label in1 "DDR Voltage"
label in2 "DDR VTT Voltage"
label in3 "NB Voltage"
label in4 "SB Voltage"
label in5 "HyperTransport Voltage"
label in6 "AGP VDDQ Voltage"
label in7 "ATX +5V"
compute in7 @*1.788 , @/1.788
label in8 "ATX +3.3V"
compute in8 @*1.248 , @/1.248
label in9 "Standby Voltage (+5V)"
compute in9 @*1.788 , @/1.788
label in10 "3VDual Voltage"
compute in10 @*1.248 , @/1.248
label temp1 "CPU Temperature"
label temp2 "SYS Temperature"
label temp3 "PWM Temperature"
ignore temp4
ignore temp5
ignore temp6
ignore temp7
label fan1 "CPU FAN Speed"
label fan2 "NB FAN Speed"
label fan3 "SYS FAN Speed"
label fan4 "AUX1 FAN Speed"
label fan5 "AUX2 FAN Speed"
ignore fan6
chip "k8temp-*"
label temp1 "Core0 Temp"
label temp2 "Core0 Temp"
label temp3 "Core1 Temp"
label temp4 "Core1 Temp"
#
# Sample configuration for the SMSC DME1737 and ASUS A8000
#
chip "dme1737-*"
# Voltage inputs
label in0 "V5stby"
label in1 "Vccp"
label in2 "V3.3"
label in3 "V5"
label in4 "V12"
label in5 "V3.3stby"
label in6 "Vbat"
# Temperature inputs
label temp1 "RD1 Temp"
label temp2 "Int Temp"
label temp3 "CPU Temp"
# Fan inputs
label fan1 "CPU Fan"
# Set voltage limits
# set in0_min 5.0 * 0.95
# set in0_max 5.0 * 1.05
# set in1_min 1.4 * 0.95
# set in1_max 1.4 * 1.05
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# set in3_min 5.0 * 0.95
# set in3_max 5.0 * 1.05
# set in4_min 12.0 * 0.95
# set in4_max 12.0 * 1.05
# set in5_min 3.3 * 0.95
# set in5_max 3.3 * 1.05
# set in6_min 3.0 * 0.95
# set in6_max 3.0 * 1.05
# Set Temp Limits
# set temp1_min 10
# set temp1_max 75
# set temp2_min 10
# set temp2_max 75
# set temp3_min 10
# set temp3_max 75
# Set Fan limits
# set fan1_min 1000
# set fan2_min 1000
# set fan3_min 1000
# set fan4_min 1000
# set fan5_min 1000
# set fan6_min 1000
#
# sample configuration for the Fintek f71882fg and f71883fg
#
# The configuration below is for the Epox EP-9U1697 GLI board, which has a
# Fintek f71883fg relabeled as Epox ep1308, this is the default config as this
# driver is developed and tested on an Epox EP-9U1697 GLI board.
#
# Premade configurations for other boards can be found at:
# http://www.lm-sensors.org/trac/wiki/Configurations/
# If your motherboard isn't listed there and you create a configuration for it
# please add it there.
#
chip "f71882fg-*"
# Temperature
label temp1 "CPU"
label temp2 "System"
ignore temp3
# Fans
label fan1 "CPU"
label fan2 "System"
label fan3 "Power"
label fan4 "Aux"
# Voltage
label in0 "3.3V"
label in1 "Vcore"
label in2 "Vdimm"
label in3 "Vchip"
label in4 "+5V"
label in5 "12V"
label in6 "5VSB"
label in7 "3VSB"
label in8 "Battery"
# never change the in0, in7 and in8 compute, these are hardwired in the chip!
compute in0 (@ * 2), (@ / 2)
compute in2 (@ * 2), (@ / 2)
compute in3 (@ * 2), (@ / 2)
compute in4 (@ * 5.25), (@ / 5.25)
compute in5 (@ * 12.83), (@ / 12.83)
compute in6 (@ * 5.25), (@ / 5.25)
compute in7 (@ * 2), (@ / 2)
compute in8 (@ * 2), (@ / 2)
chip "adm1022-*" "thmc50-*"
label temp1 "M/B Temp"
# Single CPU setup
label temp2 "CPU Temp"
# Dual CPU setup (ADM1022 only)
#label temp2 "CPU0 Temp"
#label temp3 "CPU1 Temp"
# Asus/Fintek F8000
chip "f8000-*"
# All 3 voltages are internal, but scaling is not done by the driver
# so we do it here
compute in0 @*2, @/2
compute in1 @*2, @/2
compute in2 @*2, @/2
label in0 "+3.3V"
label in1 "3VSB"
label in2 "Vbat"
Reference in new issue View Git Blame Copy Permalink