mirror of
https://github.com/lm-sensors/lm-sensors.git
synced 2026-11-03 13:38:25 +00:00
Tele42
1398ef0201
This is a bulk recovery of the sensor configs found at https://web.archive.org/web/20150901092438/http://www.lm-sensors.org:80/wiki/Configurations The config sections themselves are unaltered, but I've selectively added some, but not all of the extra info around them. Anywhere there's been extra info added, it should be in comments at the top of the config, followed by a double newline to indicate the separation. Attribution has been retained where possible, but links to the mailing list are hosed, so goto the above archive.org link to check if a config has extra origin notes. [groeck: reformatted description] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
63 lines
1.6 KiB
Plaintext
63 lines
1.6 KiB
Plaintext
# Contributed by Mark Nienberg
|
|
|
|
# sensors-detect 2.10.6 suggested the w83627thf chip, but that is wrong. The
|
|
# board actually has a Winbond W83792D according to the manual.
|
|
|
|
|
|
# Here are configurations for Winbond W83792AD/D chip.
|
|
chip "w83792d-*"
|
|
|
|
label in0 "VCoreA"
|
|
label in1 "VCoreB"
|
|
label in2 "VIN0"
|
|
label in3 "VIN1"
|
|
label in4 "VIN2"
|
|
label in5 "VIN3"
|
|
label in6 "5VCC"
|
|
label in7 "5VSB"
|
|
label in8 "VBAT"
|
|
|
|
# These are the corresponding fan names from motherboard manual.
|
|
# Rear_Fan1 through Rear_Fan4 are not read by lm_sensors, but the manual
|
|
# says that all fans are controlled by "smart fan" in BIOS.
|
|
# fan6 doesn not show up in sensor output for me.
|
|
label fan1 "Frnt_Fan3"
|
|
label fan2 "Frnt_Fan1"
|
|
label fan3 "Frnt_Fan2"
|
|
label fan4 "Frnt_Fan4"
|
|
label fan5 "Frnt_Fan5"
|
|
# label fan6 "Nothing"
|
|
label fan7 "Frnt_Fan6"
|
|
|
|
# Here is my installed fans layout
|
|
# Yours will be different
|
|
# ignore fan1
|
|
# label fan2 "Case Fan"
|
|
# ignore fan3
|
|
# label fan4 "CPU1 Fan"
|
|
# label fan5 "P/S Fan"
|
|
# ignore fan6
|
|
# ignore fan7
|
|
|
|
# Fix Case fan because speed read 0 at low speeds.
|
|
# set fan2_div 8
|
|
|
|
# Temps - I'm guessing here.
|
|
# Add 5 degrees to CPU temperatures to match BIOS
|
|
# (very limited data on which to base this)
|
|
compute temp2 @+5,@-5
|
|
compute temp3 @+5,@-5
|
|
|
|
label temp1 "MB Temp"
|
|
label temp2 "CPU1 Temp"
|
|
label temp3 "CPU2 Temp"
|
|
|
|
# Ignore chassis alarm, I don't have one
|
|
ignore chassis
|
|
|
|
# prevent alarm on in0, the actual value is about 1.1
|
|
# this is probably due to my low power 55 watt CPU
|
|
set in0_min 0.8
|
|
set in0_max 1.6
|
|
|