mirror of
https://github.com/lm-sensors/lm-sensors.git
synced 2026-11-08 16:11:26 +00:00
Tele42
1398ef0201
This is a bulk recovery of the sensor configs found at https://web.archive.org/web/20150901092438/http://www.lm-sensors.org:80/wiki/Configurations The config sections themselves are unaltered, but I've selectively added some, but not all of the extra info around them. Anywhere there's been extra info added, it should be in comments at the top of the config, followed by a double newline to indicate the separation. Attribution has been retained where possible, but links to the mailing list are hosed, so goto the above archive.org link to check if a config has extra origin notes. [groeck: reformatted description] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
64 lines
1.5 KiB
Plaintext
64 lines
1.5 KiB
Plaintext
# Configuration file contributed by Eduardo Diaz Rodriguez, based on earlier
|
|
# work by Jean Delvare. This is basically the same as for the 965P DS3, except
|
|
# that the G33 DS3R has a 3rd fan header.
|
|
|
|
|
|
# lm_sensors configuration file for the Gigabyte G33 DS3R motherboard
|
|
|
|
chip "it8718-*"
|
|
|
|
### Voltages
|
|
|
|
label in0 "Vcore"
|
|
label in1 "Vram" # "DDR18V" in BIOS
|
|
label in2 "+3.3V"
|
|
label in3 "+5V" # Not in BIOS
|
|
ignore in4
|
|
ignore in5
|
|
ignore in6
|
|
label in7 "+12V"
|
|
label in8 "Vbat" # Not in BIOS
|
|
|
|
# Vcore, Vram, +3.3V and Vbat are connected directly, so no compute
|
|
# line is needed for these. For +5V the chip is configured to use
|
|
# internal scaling. For +12V the default resistors seem to have been
|
|
# used.
|
|
compute in3 @ * (6.8/10+1), @ / (6.8/10+1)
|
|
compute in7 @ * ( 30/10+1), @ / ( 30/10+1)
|
|
|
|
# The BIOS won't set any limit for voltages.
|
|
|
|
set in0_min vid * 0.95
|
|
set in0_max vid * 1.05
|
|
set in1_min 1.8 * 0.95
|
|
set in1_max 1.8 * 1.05
|
|
set in2_min 3.3 * 0.95
|
|
set in2_max 3.3 * 1.05
|
|
set in3_min 5 * 0.95
|
|
set in3_max 5 * 1.05
|
|
set in7_min 12 * 0.95
|
|
set in7_max 12 * 1.05
|
|
|
|
### Temperatures
|
|
|
|
label temp1 "NBr Temp"
|
|
label temp2 "CPU Temp"
|
|
ignore temp3
|
|
|
|
set sensor3 0
|
|
|
|
set temp1_low 10
|
|
set temp1_over 50
|
|
set temp2_low 10
|
|
set temp2_over 60
|
|
|
|
### Fans
|
|
|
|
label fan1 "CPU Fan"
|
|
label fan2 "Case Fan"
|
|
|
|
# Adjust for your own fans
|
|
set fan1_min 1000
|
|
set fan2_min 4000
|
|
|