mirror of
https://github.com/lm-sensors/lm-sensors.git
synced 2026-11-13 17:00:15 +00:00
Tele42
1398ef0201
This is a bulk recovery of the sensor configs found at https://web.archive.org/web/20150901092438/http://www.lm-sensors.org:80/wiki/Configurations The config sections themselves are unaltered, but I've selectively added some, but not all of the extra info around them. Anywhere there's been extra info added, it should be in comments at the top of the config, followed by a double newline to indicate the separation. Attribution has been retained where possible, but links to the mailing list are hosed, so goto the above archive.org link to check if a config has extra origin notes. [groeck: reformatted description] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
71 lines
2.4 KiB
Plaintext
71 lines
2.4 KiB
Plaintext
# Configuration file contributed by Ki'Sak.
|
|
|
|
|
|
# libsensors3 configuration file for the GA-990FXA-UD3 Rev. 1.1
|
|
# This is strongly based on the Gigabyte GA-790XTA-UD4 sensors3.conf
|
|
|
|
chip "it8720-isa-*"
|
|
|
|
### Voltages
|
|
|
|
# in5 is mysterious. It is -12V in other uses of this chip, but unstable here
|
|
# -12V is in the ATX spec for ISA, which is used sparingly in modern hardware
|
|
|
|
label in0 "Vcore"
|
|
label in1 "Vdram" # "DDR3" in BIOS
|
|
label in2 "+3.3V"
|
|
label in3 "+5V" # Not in BIOS
|
|
label in4 "+12V"
|
|
ignore in5 # -12V unused
|
|
ignore in6
|
|
label in7 "5VSB" # Not in BIOS
|
|
label in8 "Vbat" # Not in BIOS
|
|
ignore cpu0_vid
|
|
|
|
### Fan labels as found on the motherboard
|
|
|
|
label fan1 "CPU_FAN" # controlled by temp3
|
|
label fan2 "SYS_FAN1" # controlled by temp1
|
|
label fan3 "SYS_FAN2"
|
|
label fan4 "PWR_FAN" # unregulated max speed
|
|
|
|
# Vcore, Vdram, +3.3V and Vbat are connected directly, so no compute
|
|
# line is needed for these. +5V and 5VSB are internal so we use the
|
|
# standard scaling factor. Scaling for +12V is apparently not standard,
|
|
# factor 3.963 is guessed from BIOS and EasyTune values (3.943 was
|
|
# another candidate.)
|
|
# These values have not been rechecked from the GA-790XTA-UD4
|
|
compute in3 @ * (6.8/10+1), @ / (6.8/10+1)
|
|
compute in4 @ * 3.963, @ / 3.963
|
|
compute in7 @ * (6.8/10+1), @ / (6.8/10+1)
|
|
|
|
# The BIOS won't set any limit for voltages.
|
|
|
|
set in0_min 0.825 * 0.95
|
|
set in0_max 1.425 * 1.05
|
|
set in1_min 1.5 * 0.95
|
|
set in1_max 1.5 * 1.05
|
|
set in2_min 3.3 * 0.95
|
|
set in2_max 3.3 * 1.05
|
|
set in3_min 5 * 0.95
|
|
set in3_max 5 * 1.05
|
|
set in4_min 12 * 0.95
|
|
set in4_max 12 * 1.05
|
|
set in7_min 5 * 0.95
|
|
set in7_max 5 * 1.05
|
|
|
|
### Temperatures
|
|
|
|
label temp1 "VRM Temp" # This is unconfirmed, Possibly near NB, but the NB
|
|
set temp1_min 0 # operates at significantly higher temps than temp1
|
|
set temp1_max 65 # Default max fan speed reference point
|
|
|
|
label temp2 "SB Temp" # This sensor reacts to nearby heat from the GPU
|
|
set temp2_min 0
|
|
set temp2_max 55 # Tropical ambient temperature plus a bit
|
|
|
|
label temp3 "CPU Temp" # k10temp truncated to whole number +12C. k10temp
|
|
set temp3_min 0 # reports thermal margin, and reports -10C when idle
|
|
set temp3_max 65 # Bulldozer Published limit +3C
|
|
|