Files
lm-sensors/configs/Gigabyte/MA785GM-US2H.conf
T
Tele42 1398ef0201 configs: Bulk config recovery from archive.org (Part 1)
This is a bulk recovery of the sensor configs found at
https://web.archive.org/web/20150901092438/http://www.lm-sensors.org:80/wiki/Configurations

The config sections themselves are unaltered, but I've selectively added
some, but not all of the extra info around them. Anywhere there's been
extra info added, it should be in comments at the top of the config,
followed by a double newline to indicate the separation. Attribution has
been retained where possible, but links to the mailing list are hosed,
so goto the above archive.org link to check if a config has extra origin
notes.

[groeck: reformatted description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2018-01-21 07:34:59 -08:00

82 lines
2.4 KiB
Plaintext

# Contributed by Glen Journeay and David Santamaría Rogado.
# lm_sensors 3 configuration file for the Gigabyte MA785GM-US2H motherboard
# 2010-8-12 G. Journeay <journeay@gmail.com>
# 2011-04-17, David Santamaría Rogado <howl.nsp@gmail.com>
# Written for board revision 1.0, may or may not be suitable for other
# revisions.
# Comments welcome!
chip "it8718-*"
### Voltages
# in7 is mysterious, it lives in the range 2.19 to 2.94 V, change with
# CPU frequency (if you take the highest clock speed of all the cores
# you can guess it's value). No idea what it can be.
label in0 "Vcore"
label in1 "Vram" # "DDR2" in BIOS
label in2 "+3.3V"
label in3 "+5V" # Not in BIOS
label in4 "+12V"
ignore in5 # Always fixed at 4.08 V
ignore in6 # Always fixed at 4.02 V
ignore in7 # Commented above
label in8 "Vbat" # Not in BIOS
# Vcore, Vram, +3.3V and Vbat are connected directly, so no compute
# line is needed for these. For +5V the chip is configured to use
# internal scaling. For +12V, my guess is that the BIOS uses 4 as
# the scaling factor. Not sure if it matches the physical reality.
# BIOS values varies between 12.048 and 12.112 V, lm-sensors in4
# between 3.040 and 3.056 V, is exactly a x4 scale +0.112 offset.
compute in3 @ * (6.8/10+1), @ / (6.8/10+1)
compute in4 @ * ((30/10)+1), @ / ((30/10)+1)
# The BIOS won't set any limit for voltages.
# You should set Vcore and Vram to match you setup, mine is:
# - CPU: AMD Athlon II X2 250 (VCore 0.85-1.425)
# - Mem: KHX8500D2/2G (Vram 1.8-2)
set in0_min 0.850 * 0.95
set in0_max 1.425 * 1.05
set in1_min 1.8 * 0.95
set in1_max 2.0 * 1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5 * 0.95
set in3_max 5 * 1.05
set in4_min 12 * 0.95
set in4_max 12 * 1.05
### Temperatures
# The BIOS only shows 2 temperature values, corresponding to Sys and CPU,
# temp3 is usually similar to Sys temp but under heavy load it raises more.
label temp1 "Sys Temp"
label temp2 "CPU Temp"
label temp3 "NBr Temp" # Guessed
set temp1_min 10
set temp1_max 50
set temp2_min 10
set temp2_max 60
set temp3_min 10
set temp3_max 50
### Fans
label fan1 "CPU Fan"
label fan2 "Case Fan"
ignore fan3
label fan4 "NBr Fan"
# Adjust for your own fans
set fan1_min 1000
set fan2_min 1000
set fan4_min 1000