mirror of
https://github.com/lm-sensors/lm-sensors.git
synced 2026-10-17 10:59:31 +00:00
Mark D. Studebaker
4572d72782
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1678 7894878c-1315-0410-8ee3-d5d059ff63e0
79 lines
2.6 KiB
Plaintext
79 lines
2.6 KiB
Plaintext
Kernel driver `mtp008.o'
|
|
=========================
|
|
|
|
Status: Complete; Beta.
|
|
This chip is quite configurable and many settings cannot
|
|
be done through the driver. Hopefully the BIOS settings will
|
|
be correct for most motherboards.
|
|
|
|
Supported chips:
|
|
* Myson MTP008
|
|
Prefix `mtp008'
|
|
Addresses scanned: I2C 0x2c - 0x2e (inclusive)
|
|
Datasheet: Publicly available at the Myson website
|
|
|
|
Author: Kris Van Hees <aedil@alchar.org>
|
|
|
|
|
|
Description
|
|
-----------
|
|
|
|
The Myson MTP008 is similar in function to the Winbond W83781D and the
|
|
National Semi LM78. See documentation for those chips for an overview.
|
|
|
|
|
|
The MTP008 chip has several pins that are configurable.
|
|
|
|
The three temperature sensors are configurable via the driver
|
|
using either the /proc entries or 'set sensorx y' statements in
|
|
/etc/sensors.conf.
|
|
One temperature input is always temp1, and the sensor type is configured
|
|
with the sensor1 entry in /proc.
|
|
One input is either in4 or temp2, and is configured with the sensor2 entry.
|
|
One input is either in5 or temp3, and is configured with the sensor3 entry.
|
|
|
|
For example, on the Tyan S1824D motherboard,
|
|
AIN4 is configured as PII temp sensor 2 and
|
|
AIN5 is hooked up to the -12V sensing circuit.
|
|
|
|
Other Tyan motherboards (the 2510 Thunder and the Tiger 200) appear to
|
|
have different configurations.
|
|
|
|
For the 2510, which has two MTP008 chips, each with a different
|
|
configuration, follow the instructions in the mtp008 section of
|
|
etc/sensors.conf.eg to configure 'sensors' correctly.
|
|
|
|
The PWM outputs are configurable via the driver.
|
|
PWM values are from 0 to 255. The first value in the /proc entry is
|
|
the pwm value; the second is the enable (0 or 1).
|
|
|
|
The fan3 and pwm1 functions share a pin.
|
|
If pwm1 is enabled than fan3 will read as 0.
|
|
|
|
The Fan input types (2 wire or 3 wire) are configurable but
|
|
not via the driver.
|
|
|
|
The driver now preserves pin settings that the BIOS configures.
|
|
If your BIOS did it right then the driver should work great.
|
|
|
|
The MTP008 has sensor type selection in /proc like the Winbond W83782D.
|
|
However, the appropriate values used to make the selection are different.
|
|
|
|
To select a sensor type, echo the value to the /proc entry, for example:
|
|
echo 1 > /proc/sys/dev/sensors/mtp008-i2c-0-2d/sensor1
|
|
Or, use /etc/sensors.conf and add a line 'set sensor1 1', for example.
|
|
Hopefully the BIOS has set these already.
|
|
|
|
Sensor selection is as follows:
|
|
|
|
Value Function Valid on sensors
|
|
----- -------- ----------------
|
|
1 Analog input (not for temperature sensing) 2,3
|
|
2 Thermistor 1,2,3
|
|
3 Pentium diode 1,2
|
|
|
|
|
|
Maintainer
|
|
-----------------
|
|
Send requests to the sensors@stimpy.netroedge.com mailing list.
|