mirror of
https://github.com/lm-sensors/lm-sensors.git
synced 2026-10-18 11:09:32 +00:00
Jean Delvare
cc405777c3
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@2480 7894878c-1315-0410-8ee3-d5d059ff63e0
78 lines
2.9 KiB
Plaintext
78 lines
2.9 KiB
Plaintext
Kernel driver `pc87360.o'
|
|
=========================
|
|
|
|
Status: Alpha, untested.
|
|
|
|
Supported chips:
|
|
* National Semiconductor PC87360, PC87363, PC87364, PC87365 and PC87366
|
|
Addresses scanned: none, address read from Super I/O config space
|
|
Datasheets:
|
|
http://www.national.com/pf/PC/PC87360.html
|
|
http://www.national.com/pf/PC/PC87363.html
|
|
http://www.national.com/pf/PC/PC87364.html
|
|
http://www.national.com/pf/PC/PC87365.html
|
|
http://www.national.com/pf/PC/PC87366.html
|
|
|
|
Authors: Jean Delvare <khali@linux-fr.org>
|
|
|
|
|
|
Module Parameters
|
|
-----------------
|
|
|
|
None.
|
|
|
|
|
|
Description
|
|
-----------
|
|
|
|
The National Semiconductor PC87360 Super I/O chip contains monitoring and
|
|
PWM control circuitry for two fans. The PC87363 chip is similar, and the
|
|
PC87364 chip has monitoring and PWM control for a third fan.
|
|
|
|
The National Semiconductor PC87365 and PC87366 Super I/O chips are complete
|
|
hardware monitoring chipsets, not only controling and monitoring three fans,
|
|
but also monitoring eleven voltage inputs and two (PC87365) or three
|
|
(PC87366) remote temperatures.
|
|
|
|
Fan rotation speeds are reported in RPM (revolutions per minute). An alarm
|
|
is triggered if the rotation speed has dropped below a programmable limit.
|
|
Fan readings can be divided by a programmable divider (1, 2, 4 or 8) to give
|
|
the readings more range or accuracy. Not all RPM values can accurately be
|
|
represented, so some rounding is done. With a divider of 2, the lowest
|
|
representable value is around 950 RPM. See doc/fan-divisors for details.
|
|
|
|
A different alarm is also triggered if the fan speed is too low to be
|
|
measured. It is suggested to increase the fan divisor in this case.
|
|
|
|
PWM values are from 0 to 255.
|
|
|
|
Temperatures are reported in degrees Celcius. Each temperature measured has
|
|
associated low, limit and overtemperature limits, each of which triggers an
|
|
alarm when crossed.
|
|
|
|
The first two temperature channels are external. The third one (PC87366
|
|
only) is internal.
|
|
|
|
Voltages are reported relatively to a reference voltage, either internal or
|
|
external. Some of them are divided by two internally, you will have to
|
|
compensate in sensors.conf. Each voltage measured has associated low and
|
|
high limit, each of which triggers an alarm when crossed.
|
|
|
|
If an alarm triggers, it will remain triggered until the hardware register
|
|
is read at least once. This means that the cause for the alarm may
|
|
already have disappeared! Note that in the current implementation, all
|
|
hardware registers are read whenever any data is read (unless it is less
|
|
than 1.5 seconds since the last update). This means that you can easily
|
|
miss once-only alarms.
|
|
|
|
|
|
Limitations
|
|
-----------
|
|
|
|
There are a few unimplemented configuration options at the moment. We'll
|
|
add them if someone needs them.
|
|
|
|
The datasheets suggests that some values (fan mins, fan divisors)
|
|
shouldn't be changed once the monitoring has started, but we ignore that
|
|
recommendation. We'll reconsider if it actually causes trouble.
|