mirror of
https://github.com/lm-sensors/lm-sensors.git
synced 2026-11-09 16:21:51 +00:00
Frodo Looijaard
8199abde46
This often-asked for, long-planned and somewhat-forgotten feature makes it possible to tell libsensors-linked applications (like the sensors program) that certain features should not be displayed. This is very nice for things like unconnected temperature sensors or fans. Modifications to the library code, to the sensors program and to the documentation and example sensors.conf file. git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@676 7894878c-1315-0410-8ee3-d5d059ff63e0
476 lines
14 KiB
Plaintext
476 lines
14 KiB
Plaintext
# Hardware sensors configuration file
|
|
|
|
# This configuration file will be used by all applications linked to
|
|
# libsensors.
|
|
|
|
# This config file consists of two parts: the heavily commented LM78
|
|
# example, and the real parts. Search for '####' if you want to skip
|
|
# to the real stuff.
|
|
|
|
# Hash marks introduce comments, which continue until the end of a line
|
|
#
|
|
# Identifiers consisting of only digits and letters can be used
|
|
# unquoted; other identifiers must be quoted. Escape characters within
|
|
# quotes operate like those in C.
|
|
|
|
# A 'chip' line specifies what the following 'label', 'compute', 'set' and
|
|
# 'ignore' lines refer to. In this case, until the
|
|
# next 'chip' line, everything refers to all lm78, lm78-j and lm79
|
|
# chips. Other examples are *-isa-* for everything on the ISA bus, and
|
|
# lm78-j-i2c-*-4e for all lm78-j chips on address 0x4e of any I2C bus.
|
|
#
|
|
# If more chip statements match a specific chip, they are all considered.
|
|
# Later lines overrule earlier lines, so if you set the in0 label for
|
|
# lm78-* to "This", and later on the in0 label for lm78-isa-* to "That",
|
|
# "That" is used for LM78 chips on the ISA bus, and "This" for LM78
|
|
# chips on a non-ISA bus.
|
|
|
|
#chip "lm78-*" "lm78-j-*" "lm79-*"
|
|
|
|
# A label line describes what a certain feature stands for on your
|
|
# mainboard. Programs can retrieve these names and display them.
|
|
# If no label is specified for a certain feature, the default name
|
|
# (ie. 'fan1' for fan1) is used.
|
|
|
|
# If you specify a label for in1, this label is also used for in1_min and
|
|
# in1_max, unless they have their own labels declared. There are several
|
|
# of these logical groups.
|
|
|
|
# These are as advised in the LM78 and LM79 data sheets, and used on almost
|
|
# any mainboard we have seen.
|
|
|
|
# label in0 "VCore 1"
|
|
# label in1 "VCore 2"
|
|
# label in2 "+3.3V"
|
|
# label in3 "+5V"
|
|
# label in4 "+12V"
|
|
# label in5 "-12V"
|
|
# label in6 "-5V"
|
|
|
|
# A compute line describes how to scale a certain feature. There are
|
|
# two expressions in it: the first describes how the /proc value must
|
|
# be translated to a user value, the second how a user value must be
|
|
# translated to a /proc value. '@' is the value to operate on. You may
|
|
# refer to other readable features (like '2 * vid').
|
|
|
|
# Like for the label statement, there are logical groups here. They are
|
|
# sometimes a bit different, though. For example, fan1_div is in the
|
|
# logical label group of fan1 (it gets the same label if none is declared
|
|
# for it), but it is not in the compute group of fan1 (as it uses a
|
|
# completely different system of values).
|
|
|
|
# For positive voltages (in0..in4), two resistors are used, with the following
|
|
# formula (R1,R2: resistor values, Vs: read voltage, Vin: pin voltage)
|
|
# R1 = R2 * (Vs/Vin - 1)
|
|
# For negative voltages (in5, in6) two resistors are used, with the following
|
|
# formula (Rin,Rf: resistor values, Vs: read voltage, Vin: pin voltage)
|
|
# Rin = (Vs * Rf) / Vin
|
|
|
|
# Here are the official LM78 and LM79 data sheet values.
|
|
# Vs R1,Rin R2,Rf Vin
|
|
# in3 +5.0 6.8 10 +2.98
|
|
# in4 +12.0 30 10 +3.00
|
|
# in5 -12.0 240 60 +3.00
|
|
# in6 -5.0 100 60 +3.00
|
|
|
|
# These would lead to these declarations:
|
|
# compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
|
|
# compute in4 ((30/10)+1)*@ , @/((30/10)+1)
|
|
# compute in5 -(240/60)*@ , -@/(240/60)
|
|
# compute in6 -(100/60)*@ , -@/(100/60)
|
|
|
|
# On almost any mainboard we have seen, the Winbond compute values lead to
|
|
# much better results, though.
|
|
|
|
# Vs R1,Rin R2,Rf Vin
|
|
# in4 +12.0 28 10 +3.00
|
|
# in5 -12.0 210 60.4 +3.00
|
|
# in6 -5.0 90.9 60.4 +3.00
|
|
|
|
# These leads to these declarations:
|
|
# compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
|
|
# compute in4 ((28/10)+1)*@ , @/((28/10)+1)
|
|
# compute in5 -(210/60.4)*@ , -@/(210/60.4)
|
|
# compute in6 -(90.9/60.4)*@ , -@/(90.9/60.4)
|
|
|
|
# Set statements set things like limits. Complete expressions can be
|
|
# used. Not everything can sensibly be set: setting 'in0', for example,
|
|
# is impossible! These settings are put through the compute translations;
|
|
# so if we specify '12.8' for in6, '3.2' will actually be written!
|
|
|
|
#set in0_max vid*1.05
|
|
#set in0_min vid*0.95
|
|
|
|
# Ignore statements tell certain features are not wanted. User programs can
|
|
# still read them if they really want, though; this is just an advisory
|
|
# marking. 'in0' would also invalidate 'in0_max' and 'in0_min'.
|
|
#
|
|
#ignore in0
|
|
|
|
|
|
# There is one other feature: the 'bus' statement. An example is below.
|
|
|
|
#bus "i2c-0" "SMBus PIIX4 adapter at e800" "Non-I2C SMBus adapter"
|
|
|
|
# If we refer from now on to 'i2c-0' in 'chip' lines, this will run-time
|
|
# be matched to this bus. So even if the PIIX4 is called 'i2c-5' at that
|
|
# moment, because five other adapters were detected first, 'i2c-0' in
|
|
# the config file would always only match this physical bus. In the above
|
|
# config file, this feature is not needed; but the next lines would
|
|
# only affect the LM75 chips on the PIIX4 adapter:
|
|
|
|
#chip "lm75-i2c-0-*"
|
|
|
|
# You should really use the output of /proc/bus/chips to generate bus lines,
|
|
# because one mistyped characted will inhibit the match. Wildcards are not
|
|
# yet supported; spaces at the end are ignored, though.
|
|
|
|
|
|
|
|
|
|
|
|
#### Here begins the real configuration file
|
|
|
|
chip "lm78-*" "lm78-j-*" "lm79-*" "w83781d-*" "sis5595-*"
|
|
|
|
# These are as advised in the LM78 and LM79 data sheets, and used on almost
|
|
# any mainboard we have seen.
|
|
|
|
label in0 "VCore 1"
|
|
label in1 "VCore 2"
|
|
label in2 "+3.3V"
|
|
label in3 "+5V"
|
|
label in4 "+12V"
|
|
label in5 "-12V"
|
|
label in6 "-5V"
|
|
|
|
# For positive voltages (in0..in4), two resistors are used, with the following
|
|
# formula (R1,R2: resistor values, Vs: read voltage, Vin: pin voltage)
|
|
# R1 = R2 * (Vs/Vin - 1)
|
|
# For negative voltages (in5, in6) two resistors are used, with the following
|
|
# formula (Rin,Rf: resistor values, Vs: read voltage, Vin: pin voltage)
|
|
# Rin = (Vs * Rf) / Vin
|
|
|
|
# Here are the official LM78 and LM79 data sheet values.
|
|
# Vs R1,Rin R2,Rf Vin
|
|
# in3 +5.0 6.8 10 +2.98
|
|
# in4 +12.0 30 10 +3.00
|
|
# in5 -12.0 240 60 +3.00
|
|
# in6 -5.0 100 60 +3.00
|
|
|
|
# These would lead to these declarations:
|
|
# compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
|
|
# compute in4 ((30/10)+1)*@ , @/((30/10)+1)
|
|
# compute in5 -(240/60)*@ , -@/(240/60)
|
|
# compute in6 -(100/60)*@ , -@/(100/60)
|
|
|
|
# On almost any mainboard we have seen, the Winbond compute values lead to
|
|
# much better results, though.
|
|
|
|
# Vs R1,Rin R2,Rf Vin
|
|
# in4 +12.0 28 10 +3.00
|
|
# in5 -12.0 210 60.4 +3.00
|
|
# in6 -5.0 90.9 60.4 +3.00
|
|
|
|
# These leads to these declarations:
|
|
|
|
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
|
|
compute in4 ((28/10)+1)*@ , @/((28/10)+1)
|
|
compute in5 -(210/60.4)*@ , -@/(210/60.4)
|
|
compute in6 -(90.9/60.4)*@ , -@/(90.9/60.4)
|
|
|
|
# Here, we assume the VID readings are valid, and we use a max. 5% deviation
|
|
|
|
set in0_min vid*0.95
|
|
set in0_max vid*1.05
|
|
set in1_min vid*0.95
|
|
set in1_max vid*1.05
|
|
set in2_min 3.3 * 0.95
|
|
set in2_max 3.3 * 1.05
|
|
set in3_min 5.0 * 0.95
|
|
set in3_max 5.0 * 1.05
|
|
set in4_min 12 * 0.95
|
|
set in4_max 12 * 1.05
|
|
set in5_min -12 * 0.95
|
|
set in5_max -12 * 1.05
|
|
set in6_min -5 * 0.95
|
|
set in6_max -5 * 1.05
|
|
|
|
|
|
chip "w83782d-*" "w83783s-*" "w83627hf-*"
|
|
|
|
# Same as above for w83781d except that in5 and in6 are computed differently.
|
|
# Rather than an internal inverting op amp, the 82d/83s use standard positive
|
|
# inputs and the negative voltages are level shifted by a 3.6V reference.
|
|
# The math is convoluted, so we hope that your motherboard
|
|
# uses the recommended resistor values.
|
|
|
|
label in0 "VCore 1"
|
|
label in1 "VCore 2"
|
|
label in2 "+3.3V"
|
|
label in3 "+5V"
|
|
label in4 "+12V"
|
|
label in5 "-12V"
|
|
label in6 "-5V"
|
|
label in7 "V5SB"
|
|
label in8 "VBat"
|
|
|
|
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
|
|
compute in4 ((28/10)+1)*@ , @/((28/10)+1)
|
|
compute in5 (5.14 * @) - 14.91 , (@ + 14.91) / 5.14
|
|
compute in6 (3.14 * @) - 7.71 , (@ + 7.71) / 3.14
|
|
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)
|
|
|
|
# set limits to 5% for the critical voltages
|
|
# set limits to 10% for the non-critical voltages
|
|
# set limits to 20% for the battery voltage
|
|
|
|
set in0_min vid*0.95
|
|
set in0_max vid*1.05
|
|
set in1_min vid*0.95
|
|
set in1_max vid*1.05
|
|
set in2_min 3.3 * 0.95
|
|
set in2_max 3.3 * 1.05
|
|
set in3_min 5.0 * 0.95
|
|
set in3_max 5.0 * 1.05
|
|
set in4_min 12 * 0.90
|
|
set in4_max 12 * 1.10
|
|
set in5_min -12 * 0.90
|
|
set in5_max -12 * 1.10
|
|
set in6_min -5 * 0.95
|
|
set in6_max -5 * 1.05
|
|
set in7_min 5 * 0.95
|
|
set in7_max 5 * 1.05
|
|
set in8_min 3.0 * 0.80
|
|
set in8_max 3.0 * 1.20
|
|
|
|
# set up sensor types (thermistor is default)
|
|
# 1 = PII/Celeron Diode; 2 = 3904 transistor;
|
|
# 3435 = thermistor with Beta = 3435
|
|
# If temperature changes very little, try 1 or 2.
|
|
# set sensor1 1
|
|
# set sensor2 2
|
|
# set sensor3 3435
|
|
|
|
|
|
chip "as99127f-*"
|
|
|
|
# Same as above for w83782d except that in5 and in6 negative voltages
|
|
# are computed as in the w83781d.
|
|
|
|
label in0 "VCore 1"
|
|
label in1 "VCore 2"
|
|
label in2 "+3.3V"
|
|
label in3 "+5V"
|
|
label in4 "+12V"
|
|
label in5 "-12V"
|
|
label in6 "-5V"
|
|
label in7 "V5SB"
|
|
label in8 "VBat"
|
|
|
|
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
|
|
compute in4 ((28/10)+1)*@ , @/((28/10)+1)
|
|
compute in5 -(210/60.4)*@ , -@/(210/60.4)
|
|
compute in6 -(90.9/60.4)*@ , -@/(90.9/60.4)
|
|
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)
|
|
|
|
# set limits to 5% for the critical voltages
|
|
# set limits to 10% for the non-critical voltages
|
|
# set limits to 20% for the battery voltage
|
|
|
|
set in0_min vid*0.95
|
|
set in0_max vid*1.05
|
|
set in1_min vid*0.95
|
|
set in1_max vid*1.05
|
|
set in2_min 3.3 * 0.95
|
|
set in2_max 3.3 * 1.05
|
|
set in3_min 5.0 * 0.95
|
|
set in3_max 5.0 * 1.05
|
|
set in4_min 12 * 0.90
|
|
set in4_max 12 * 1.10
|
|
set in5_min -12 * 0.90
|
|
set in5_max -12 * 1.10
|
|
set in6_min -5 * 0.95
|
|
set in6_max -5 * 1.05
|
|
set in7_min 5 * 0.95
|
|
set in7_max 5 * 1.05
|
|
set in8_min 3.0 * 0.80
|
|
set in8_max 3.0 * 1.20
|
|
|
|
# set up sensor types (thermistor is default)
|
|
# 1 = PII/Celeron Diode; 2 = 3904 transistor;
|
|
# 3435 = thermistor with Beta = 3435
|
|
# If temperature changes very little, try 1 or 2.
|
|
# set sensor1 1
|
|
# set sensor2 2
|
|
# set sensor3 3435
|
|
|
|
|
|
chip "gl518sm-*"
|
|
|
|
# Factors and labels taken from GL518SM datasheet, they seem to give
|
|
# reasonable values with EISCA connected Fan78
|
|
|
|
label vdd "+5V"
|
|
label vin1 "+3.3V"
|
|
label vin2 "+12V"
|
|
label vin3 "Vcore"
|
|
|
|
# vin2 depends on external resistors (4,7k and 15k assumed here)
|
|
# vin1 and vin3 require no scaling
|
|
|
|
compute vin2 (197/47)*@ , @/(197/47)
|
|
|
|
set vdd_min 4.8
|
|
set vdd_max 5.2
|
|
set vin1_min 3.20
|
|
set vin1_max 3.40
|
|
set vin2_min 11.0
|
|
set vin2_max 13.0
|
|
set vin3_min 2.10
|
|
set vin3_max 2.30
|
|
set fan1_off 0
|
|
set fan2_min 0
|
|
set iterate 0
|
|
|
|
chip "gl520sm-*"
|
|
|
|
# Factors and labels taken from GL520SM datasheet
|
|
|
|
label vdd "+5V"
|
|
label vin1 "+3.3V"
|
|
label vin2 "+12V"
|
|
label vin3 "Vcore"
|
|
label vin4 "-12V"
|
|
|
|
# vin1 and vin3 require no scaling
|
|
# vin2 depends on external resistors (4,7k and 15k assumed)
|
|
|
|
# vin4 = ((R1+R2)/R2)*@ - (R1/R2)*vdd
|
|
#
|
|
# -12 --| R1 |---t---| R2 |-- +5
|
|
# |
|
|
# vin4
|
|
#
|
|
|
|
compute vin2 (197/47)*@ , @/(197/47)
|
|
compute vin4 (5*@)-(4*vdd) , (@+4*vdd)/5
|
|
|
|
set vdd_min 4.8
|
|
set vdd_max 5.2
|
|
set vin1_min 3.20
|
|
set vin1_max 3.40
|
|
set vin2_min 11.0
|
|
set vin2_max 13.0
|
|
set vin3_min 2.10
|
|
set vin3_max 2.30
|
|
set two_temps 1
|
|
|
|
chip "lm80-*"
|
|
|
|
# The values below should be correct if you own a qdi BX (brilliant1)
|
|
# mainboard. If not, please contact us, so we can figure out better readings.
|
|
# Many thanks go to Peter T. Breuer <ptb@it.uc3m.es> for helping us figure
|
|
# out how to handle the LM80.
|
|
|
|
# For positive voltages (in0..in4), two resistors are used, with the following
|
|
# formula (R1,R2: resistor values, Vs: read voltage, Vin: pin voltage)
|
|
# R1 = R2 * (Vs/Vin - 1)
|
|
# For negative voltages (in5, in6) two resistors are used, with the following
|
|
# formula (R3,R4: resistor values, Vs: read voltage, Vin: pin voltage,
|
|
# V5: +5V)
|
|
# R3 = R4 * (Vs - Vin) / (Vin - V5)
|
|
|
|
# Here are the official LM78 and LM79 data sheet values.
|
|
# Vs R1,R3 R2,R4 Vin
|
|
# +2.5V 23.7 75 +1.9
|
|
# +3.3V 22.1 30 +1.9
|
|
# +5.0 24 14.7 +1.9
|
|
# +12.0 160 30.1 +1.9
|
|
# -12.0 160 35.7 +1.9
|
|
# -5.0 36 16.2 +1.9
|
|
|
|
# Now curiously enough, VCore is connected with (unknown) resistors, which
|
|
# translate a +2.8V to +1.9V. So we use that in the computations below.
|
|
|
|
label in0 "+5V"
|
|
label in1 "VTT"
|
|
label in2 "+3.3V"
|
|
label in3 "+Vcore"
|
|
label in4 "+12V"
|
|
label in5 "-12V"
|
|
label in6 "-5V"
|
|
|
|
compute in0 (24/14.7 + 1) * @ , @ / (24/14.7 + 1)
|
|
compute in2 (22.1/30 + 1) * @ , @ / (22.1/30 + 1)
|
|
compute in3 (2.8/1.9) * @, @ * 1.9/2.8
|
|
compute in4 (160/35.7 + 1) * @, @ / (160/35.7 + 1)
|
|
compute in5 (160/35.7)*(@ - in0) + @, (@ + in0 * 160/25.7)/ (1 + 160/25.7)
|
|
compute in6 (36/16.2)*(@ - in0) + @, (@ + in0 * 36/16.2) / (1 + 36/16.2)
|
|
|
|
set in0_min 5 * 0.95
|
|
set in0_max 5 * 0.95
|
|
# What is your VTT? It is probably not this value...
|
|
set in1_min 2*0.95
|
|
set in1_max 2*1.05
|
|
set in2_min 3.3 * 0.95
|
|
set in2_max 3.3 * 1.05
|
|
# What is your VCore? It is probably not this value...
|
|
set in3_min 1.9 * 0.95
|
|
set in3_max 1.9 * 1.05
|
|
set in4_min 12 * 0.95
|
|
set in4_max 12 * 1.05
|
|
set in5_min -12 * 0.95
|
|
set in5_max -12 * 1.05
|
|
set in6_min -5 * 0.95
|
|
set in6_max -5 * 1.05
|
|
|
|
|
|
chip "maxilife-cg-*" "maxilife-co-*" "maxilife-as-*"
|
|
|
|
label fan1 "HDD Fan"
|
|
label fan2 "PCI Fan"
|
|
label fan3 "CPU Fan"
|
|
|
|
label temp2 "PCI Temp"
|
|
label temp4 "HDD Temp"
|
|
label temp5 "CPU Temp"
|
|
|
|
label vid1 "V+12"
|
|
|
|
# vid1 need to be scaled by 6.337 other voltages
|
|
# require no scaling
|
|
|
|
compute vid1 6.337*@ , @/6.337
|
|
|
|
|
|
chip "maxilife-cg-*"
|
|
|
|
# invalid temp1
|
|
label temp3 "BX Temp"
|
|
|
|
label vid2 "Vcpu1"
|
|
label vid3 "Vcpu2"
|
|
# invalid vid4
|
|
|
|
|
|
chip "maxilife-co-*"
|
|
|
|
label temp1 "CPU 1 Temp"
|
|
label temp3 "CPU 2 Temp"
|
|
|
|
label vid2 "Vcpu1"
|
|
label vid3 "Vcpu2"
|
|
label vid4 "VcacheL2"
|
|
|
|
|
|
chip "maxilife-as-*"
|
|
|
|
# invalid temp1
|
|
# invalid temp3
|
|
|
|
label vid2 "Vcpu"
|
|
# invalid vid3
|
|
# invalid vid4
|
|
|