mirror of
https://github.com/lm-sensors/lm-sensors.git
synced 2026-10-26 12:24:33 +00:00
Frodo Looijaard
f3cfdfa7a5
This file consists of two numbers: the first is either 0 (global sound alarm disable) or 1 (enable), the second is in the same encoding as the 'alarm' file and determines for which alarms the speaker will sound. The new file was added to the module, the library and the sensors application. git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@112 7894878c-1315-0410-8ee3-d5d059ff63e0
80 lines
4.1 KiB
Plaintext
80 lines
4.1 KiB
Plaintext
This file documents the gl518sm directories.
|
|
|
|
There will be one directory created for each detected GL518SM chip. Chips
|
|
can only be connected to the SMBus. Directories are called
|
|
gl518sm-r??-i2c-?-??, where the first two question marks are the revision
|
|
number, the question mark after i2c equals the I2C bus number, and the I2C
|
|
address is at the end.
|
|
At this moment, revisions 0x00 and 0x80 are known and supported. Revision
|
|
0x00 chips can only display the VIN3 value; revision 0x80 can also
|
|
display the VIN1, VIN2 and VDD values.
|
|
/proc/sys/dev/sensors/chips contains the SYSCTL values for all chip
|
|
directories.
|
|
|
|
Within each LM78 directory, you can find the following files:
|
|
* alarms (GL518_SYSCTL_ALARMS)
|
|
A number which indicates which alarms are on. An alarm gets triggered when
|
|
some limit has been crossed. Even if the cause of the alarm is over, it
|
|
stays triggered until it has been read at least once. Because the LM78
|
|
values are updated at most once every 1.5 seconds, this means the alarm
|
|
can be read several times before it is erased.
|
|
This file can not be written to.
|
|
The number is the logical OR of the following components:
|
|
- GL518_ALARM_VDD
|
|
Gets triggered when the VDD value is higher or lower than its limits
|
|
- LM78_ALARM_VIN[1-3]
|
|
Gets triggered when the corresponding VIN value is higher or lower than
|
|
its limits.
|
|
- LM78_ALARM_TEMP
|
|
Gets triggered when the temp value has crossed its limits. See the
|
|
description under temp.
|
|
- LM78_ALARM_FAN[1-2]
|
|
Gets triggered when the corresponding FAN value drops below its limit.
|
|
If accessed through sysctl, this value is a long.
|
|
* beep (GL518_SYSCTL_BEEP)
|
|
Two numbers. The first is 0 if all sound signals are disabled; it is 1 if
|
|
they are enabled. The second number determines which alarms will cause
|
|
a sound signal, if the first number is set to 1. The encoding of the
|
|
second number is the same as that in alarms.
|
|
* fan[1-2] (GL518_SYSCTL_FAN[1-2])
|
|
A list of two numbers. The first is the minimum fan rotation limit; the
|
|
second is the current fan rotation speed. Both are in RPM (rotation per
|
|
minute). An alarm is triggered if the rotation speed drops below the
|
|
limit. The first value can be changed. Not all RPM values can accurately
|
|
be represented, so some rounding is done.
|
|
If accessed through sysctl, this is a list of longs.
|
|
* fan_div (GL518_SYSCTL_FAN_DIV)
|
|
A list of two numbers, one for each fan. Each number can be either 1, 2,
|
|
4 or 8. It is the internal scaling factor used for the FAN rotations. If
|
|
you change this number, the FAN readings get more or less detailed, but
|
|
the range in which they can be read too. Higher numbers give better
|
|
resolution, but less range. The first two numbers can be changed, the
|
|
third not.
|
|
If accessed through sysctl, this is a list of longs.
|
|
* vin[1-3] and vdd (LM78_SYSCTL_VIN[1-3] and GL518_SYSCTL_VDD)
|
|
A list of three numbers. The first is the minimum limit, the second is the
|
|
maximum limit, and the third is the current value. If you have a weird
|
|
mainboard, all values may be off because some other scaling factor has
|
|
to be used; user-space programs should compensate for this. Note that
|
|
minimum means 'closest to zero'; so if the normal value equals -10, a
|
|
minimum could equal -9, and a maximum -11.
|
|
On GL518SM revision 0 chips, only VIN3 is readable; for the others,
|
|
you can set limits, but you can not read the current values.
|
|
The first two numbers can be changed, the third not.
|
|
If accessed through sysctl, this is a list of longs, each being the voltage
|
|
times 100.
|
|
* temp
|
|
A list of three numbers. The first number is the Overtemperature Shutdown
|
|
value; the second is the Hysteris value and the third number is the
|
|
current value. The first two values can be modified. All values are in
|
|
degrees Celcius.
|
|
An alarm is issued when the temperature gets higher then the
|
|
Overtemperature Shutdown value; it stays on until the temperature falls
|
|
below the Hysteris value.
|
|
The first two numbers can be changed, the third not.
|
|
If accessed through sysctl, this is a list of longs, each being the
|
|
temperature times 10.
|
|
|
|
The data for each GL518SM is updated each 1.5 seconds, but only if it is
|
|
actually read.
|