finit/doc/build.md

Building Finit
==============

Finit comes with a traditional configure script to control features and
optional plugins to enable.  It depends on three external libraries:

- [libuEv][], the event loop
- [libite][] (-lite), much needed frog DNA
- [libConfuse][], the parser behind the .conf format

The bundled device manager, keventd, needs a fourth: libblkid from
[util-linux][].  It reads the filesystem UUID and label off block
devices, which is what the curated rules name the `/dev/disk/by-uuid/`
and `/dev/disk/by-label/` symlinks after.  keventd is enabled by
default, so this is a hard requirement unless you build with
`--without-keventd`.

> [!IMPORTANT]
> Most free/open source software packages that use `configure` default
> to install to `/usr/local`.  However, some Linux distributions do no
> longer search that path for installed software, e.g. Fedora and Alpine
> Linux.  To get finit's configure script to find its dependencies you
> have to help the `pkg-config` tool a bit if you do not change the
> default prefix path:
>
>     PKG_CONFIG_LIBDIR=/usr/local/lib/pkgconfig ./configure

The configure script checks for all dependencies, including the correct
version of the above mentioned libraries.  Currently required versions:

- libite v2.2.0, or later
- libuEv v2.2.0, or later
- libConfuse v3.3, or later
- libblkid, any version, when keventd is enabled


Configure
---------

Below are a few of the main switches to configure:

* `--prefix=..`: Usually you want to set this to `/usr`, default is the GNU
  default: `/usr/local`

* `--exec-prefix=..`: This you want to set to the empty string, or `/`, to
  ensure the programs `finit` and `initctl` are installed to the proper
  locations.  Linux expects an "init" in `/sbin`, default: `--prefix`

* `--sysconfdir=..`: follows `--prefix`, you likely want it to be `/etc`

* `--localstatedir=..`: follows `--prefix`, you likely want `/var`

* `--enable-static`: Build Finit statically.  The plugins will be
  built-ins (.o files) and all external libraries, except the C library
  will be linked statically.

* `--enable-kernel-cmdline`: Enable Finit pre-4.1 parsing of init args from
  `/proc/cmdline`, this is *not recommended* since Finit may be running as the
  init for container apps that can see the host's `/proc` filesystem

* `--disable-dbus`: Opt out of Finit's built-in D-Bus support, enabled by
  default.  See [D-Bus Integration](dbus.md) for what it provides.  Not to
  be confused with `--disable-dbus-plugin` below, which only governs
  starting an external `dbus-daemon`

* `--enable-alsa-utils-plugin`: Enable the optional `alsa-utils.so` sound plugin.

* `--disable-dbus-plugin`: Drop the `dbus.so` plugin, which launches
  `dbus-daemon` at boot.  Enabled by default; the plugin does nothing on
  a system that has no `dbus-daemon` installed, so opting out is only
  needed to keep init from starting a bus on a system that has one.
  Unrelated to the built-in bus, see `--disable-dbus` above.

* `--enable-resolvconf-plugin`: Enable the `resolvconf.so` optional plugin.

* `--enable-x11-common-plugin`: Enable the optional X Window `x11-common.so` plugin.

* `--without-keventd`: Drop the bundled device manager, for systems that
  run mdev, mdevd, or udevd instead.  Enabled by default, and the only
  thing that pulls in libblkid.  See [Bundled Device Manager](keventd.md).

* `--without-sulogin`: Drop the bundled `sulogin`, enabled by default,
  and use the system `sulogin(8)` instead.  The one shipped with Finit
  *allows password-less* login if the `root` user is disabled or has no
  password at all.  `--with-sulogin=USER` prompts for another user's
  password than `root`'s.

* `--without-watchdog`: Drop the bundled `watchdogd`, enabled by default
  on `/dev/watchdog`, `--with-watchdog=DEV` selects another device.
  Finit starts it when the device node exists, see [Watchdog](watchdog.md).

* `--with-libsystemd`: Build the replacement `libsystemd`, which lets
  programs that use `sd_notify()` talk to Finit without systemd.  Off by
  default because it installs `libsystemd.so.0` in `$libdir`: on a host
  that has the real one, ours shadows it in the loader cache and every
  program linking it, `dbus-daemon` and `udevd` included, loses the
  symbols it needs.  Safe on a systemd-free system, which is the point
  of it.

For more configure flags, see <kbd>./configure --help</kbd>

> [!NOTE]
> The configure script is not available in the GIT sources.  It is
> however included in (officially supported) released tarballs.  The
> idea is that you should not need GNU autotools to build, only the
> above mentioned dependencies, a POSIX shell, a C compiler and make.
> Any contributing to Finit can generate it from `configure.ac` using
> the `autogen.sh` script.


Example
-------

First, unpack the archive:

```shell
$ tar xf finit-4.3.tar.gz
$ cd finit-4.3/
```

Then configure, build and install:

```shell
$ ./configure --prefix=/usr                 --exec-prefix=         \
              --sysconfdir=/etc             --localstatedir=/var
$ make
.
.
.
$ DESTDIR=/tmp/finit make install
```

In this example the [finit-4.3.tar.gz][1] archive is unpacked to the
user's home directory, configured, built and installed to a temporary
staging directory.  The environment variable `DESTDIR` controls the
destination directory when installing, very useful for building binary
standalone packages.

Finit 4.1 and later can detect if it runs on an embedded system, or a
system that use BusyBox tools instead of udev & C:o.  On such systems
`mdev` instead of `udev` is used.  However, remember to also change the
Linux config to:

    CONFIG_UEVENT_HELPER_PATH="/sbin/mdev"

> [!TIP]
> If you run into problems starting Finit, take a look at `finit.c`.
> One of the most common problems is a custom Linux kernel build that
> lack `CONFIG_DEVTMPFS`.  Another is too much cruft in the system
> `/etc/fstab`.


Testing
-------

`make check` runs the test suite in a private namespace, so it is safe
on a running system.  It needs `unshare` and, on Ubuntu, unprivileged
user namespaces enabled:

```shell
sudo sysctl kernel.apparmor_restrict_unprivileged_userns=0
make check
```

The D-Bus message parser is the only place in Finit where bytes off a
socket become pointers, so it also has a fuzz target.  `make check`
runs it as a fixed sweep, which takes milliseconds and needs nothing
beyond the normal build.  To fuzz it properly, build it with clang and
libFuzzer:

```shell
clang -fsanitize=fuzzer,address -DLINK_FUZZ_LIBFUZZER -D_GNU_SOURCE \
      -I libink -I . -o fuzz-msg-parse                              \
      test/src/fuzz-msg-parse.c libink/*.c
mkdir -p .fuzz-corpus
./fuzz-msg-parse .fuzz-corpus -max_total_time=300
```

Give it a corpus directory as above and it saves what it learns there,
so the next run picks up where this one left off instead of starting
cold.  Nothing writes to it unless you name it: without the argument
libFuzzer keeps everything in memory and the run leaves only crashes
behind.  `make distclean` clears the corpus and the target.

Once a corpus has grown, most of it reaches code some earlier input
already reached.  Minimise it:

```shell
./fuzz-msg-parse -merge=1 .fuzz-corpus-min .fuzz-corpus
rm -rf .fuzz-corpus && mv .fuzz-corpus-min .fuzz-corpus
```

Run `./configure` first, the target needs the generated `config.h`.
If the link fails with `cannot find -lstdc++`, install the `libstdc++`
headers matching the newest GCC on the system, not the default one:
clang picks the newest tree it finds, and that is the one that needs
them.  CI runs this target on every pull request, carrying its
corpus between runs so it reaches deeper over time.

Feed a file back to the target to reproduce a find:

```shell
./fuzz-msg-parse crash-3f2a...
```


Running
-------

Having successfully built Finit it is now be time to take it for a test
drive.  The `make install` attempts to set up finit as the system system
init, `/sbin/init`, but this is usually a symlink pointing to the
current init.

So either change the symlink, or change your boot loader (GRUB, LOADLIN,
LILO, U-Boot/Barebox or RedBoot) configuration to append the following
to the kernel command line:

```shell
append="init=/sbin/finit"
```

Remember to also set up an initial `/etc/finit.conf` before rebooting!


Recovery
--------

To rescue a system with Finit, append the following to the kernel
command line:

```shell
append="init=/sbin/finit rescue"
```

This tells Finit to start in a very limited recovery mode, no services
are loaded, no filesystems are mounted or checked, and no networking is
enabled.  The default Finit rescue mode configuration is installed into
`/lib/finit/rescue.conf`, which can be safely removed or changed.

By default the a root shell, without login, is started.

> [!IMPORTANT]
> In rescue mode `initctl` will not work, the same goes for `reboot`,
> `shutdown`, and `poweroff` commands, provided they are the Finit
> versions of these commands.  Use the `-f` flag to force the action.


Debugging
---------

Edit, or append to, the kernel command line: remove `quiet` to enable
kernel messages and add `finit.debug` to enable Finit debug messages.

```shell
append="init=/sbin/finit -- finit.debug"
```

Notice the `--` separator.

To debug startup issues, in particular issues with getty/login, add
the following to your Finit .conf file:

    tty board {
        runlevel = "12345789"
        notty    = true
        noclear  = true
    }

The `notty` option ensures reusing the stdin/stdout set up by the
kernel.  Remember, this is only for debugging and would leave your
production system potentially wide open.

There is also a rescue shell available, in case Finit crashes and the
kernel usually reboots: `configure --enable-emergency-shell`.  However,
the behavior of Finit is severely limited when this is enabled, so use
it only for debugging start up issues when Finit crashes.

> [!CAUTION]
> None of these options should be enabled on production systems since
> they can potentially give a user root access.

[1]:       https://github.com/finit-project/finit/releases/download/4.3/finit-4.3.tar.gz
[libuEv]:  https://github.com/troglobit/libuev
[libite]:  https://github.com/troglobit/libite
[libConfuse]: https://github.com/libconfuse/libconfuse
[util-linux]: https://github.com/util-linux/util-linux