mirror of
https://github.com/troglobit/finit.git
synced 2026-10-01 05:22:48 +07:00
Joachim Wiberg
2f91ab5eac
This change adds support for a new command line option finit.config=PATH
which can be used to tell Finit to start with /etc/factory.conf instead
of /etc/finit.conf.
For the complete experience a new top-level configuration file directive
`rcsd PATH` has aslo been added. It in turn can be used by factory.conf
as follows to override /etc/finit.d:
rcsd /etc/factory.d
Manually verified in myLinux
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
107 lines
4.7 KiB
Markdown
107 lines
4.7 KiB
Markdown
Tips & Tricks with the kernel cmdline
|
|
=====================================
|
|
|
|
This document summarizes the different boot parameters that can be
|
|
passed on the Linux kernel command line. Not limited to Finit.
|
|
|
|
The `bool` setting is one of `on, off, true false, 1, 0`.
|
|
|
|
> **NOTE:** remember to use `--` to separate kernel parameters from
|
|
> parameters to init. E.g., `init=/sbin/finit -- finit.debug rescue`
|
|
|
|
* `debug`: Enable kernel debug. Debug messages are printed to the
|
|
console until Finit starts up, unless `loglevel=7` (below) is used.
|
|
|
|
* `finit.cond=foo[,bar[,baz]]`: set `<boot/foo>` condition, optionally
|
|
multiple conditions can be set using the same option, separated with a
|
|
comma. Alternatively, multiple `foo.cond=arg` can be given. Each will
|
|
result in a `<boot/arg>` condition being set to control the rest of the
|
|
system bootstrap.
|
|
|
|
Very useful for selecting different boot modes, e.g. manufacturing test,
|
|
firmware upgrade, or rescue mode.
|
|
|
|
> Note: `<boot/...>` conditions cannot be cleared with `initctl`!
|
|
|
|
* `finit.config=/path/to/alternative/finit.conf`: override the
|
|
compile-time bootstrap config file, default:
|
|
|
|
./configure --with-config=/etc/finit.conf
|
|
|
|
Useful when starting up in various rescue mode, factory, or
|
|
production test setups. Use the top-level configuration file
|
|
directive `rcsd /path/to/finit.d` to override the default
|
|
rcS.d directory.
|
|
|
|
* `finit.debug[=bool]`: Enable finit debug. This is operated
|
|
independently of the kernel `debug` setting. New as of Finit v4.
|
|
|
|
* `finit.fstab=</path/to/etc/fstab.alternative>`: Tell Finit to use an
|
|
alternate `fstab` to mount the file system from. Remember, this file
|
|
must be on the `root=...` file system provided to Finit from the
|
|
kernel. By default the built-in fstab is used, which itself defaults
|
|
to `/etc/fstab`, but can be changed at build time with:
|
|
|
|
./configure --with-fstab=/path/to/fstab
|
|
|
|
It is even possible to disable a built-in default using:
|
|
|
|
./configure --without-fstab
|
|
|
|
Making `finit.fstab=/path/to/fstab` a *mandatory* command line option.
|
|
Note, if the command line fstab is missing, Finit falls back to the
|
|
built-in fstab, and if both are missing, the system treats this as a
|
|
bad `fsck` and thus calls `sulogin`. If, in turn, `sulogin` is not
|
|
available on the system, Finit calls reboot, which is also what will
|
|
happen when a user exits from `sulogin`.
|
|
|
|
* `finit.status[=bool]`: Control finit boot progress, including banner.
|
|
(Used to be `finit.show_status`, which works but is deprecated.)
|
|
|
|
* `finit.status_style=<classic,modern>`: Set Finit boot progress style,
|
|
when enabled.
|
|
|
|
* `init=/bin/sh`: Bypass system default init and tell kernel to start a
|
|
shell. Note, this shell is very limited and does not support
|
|
signals and has no job control. Recommend using, and modifying,
|
|
`rescue` mode instead.
|
|
|
|
* `loglevel=<0-7>`, sets the kernel's log level, which is more granular
|
|
than `debug`. Also, when `loglevel=7`, Finit will *not disable*
|
|
kernel logs to the console. This is very useful when debugging the
|
|
kernel at system bring-up. Since `loglevel=7` is the same as `debug`
|
|
this means you have to use `quiet` for a quiet boot, until sysklogd
|
|
takes over logging of kernel events.
|
|
|
|
* `panic=SEC`: By default the kernel does not reboot after a kernel
|
|
panic. This setting will cause a kernel reboot after SEC seconds.
|
|
|
|
* `quiet`: Suppress kernel logging to console, except for warnings and
|
|
errors. Also, see `loglevel` and `quiet` above.
|
|
|
|
* `rescue`: Start rescue/maintenance mode. If your system comes with
|
|
the bundled `sulogin` program (Finit, or from util-linux/Busybox),
|
|
you will be given a root login to a maintenance shell. However, if
|
|
`sulogin` is missing, the file `/lib/finit/rescue.conf` is read and
|
|
the system booted in a limited fallback mode. See [config.md][]
|
|
for more information.
|
|
|
|
**Note:** in this mode `initctl` will not work. Correct the problem
|
|
and use `reboot -f` to force reboot.
|
|
|
|
* `single`, or `S`: Single user mode, runlevel 1, in Finit. Useful to
|
|
debug problems with the regular runlevel. All services and TTYs in
|
|
`[1]` will be started, so a `tty [1] @console nologin` configuration
|
|
presents you with a root console without login.
|
|
|
|
* `1-9`, except `6`: override the configured `runlevel`. Like the `S`
|
|
and `rescue`, giving a single number on the kernel command line tells
|
|
Finit to ignore any `runlevel` in `/etc/finit.conf` as well as the
|
|
configure fallback `--with-runlevel=N` setting. Remember, `6` is the
|
|
reboot runlevel and is not permitted. Any other values are ignored.
|
|
|
|
For more on kernel boot parameters, see the man page [bootparam(7)][].
|
|
|
|
[config.md]: config.md#rescue-mode
|
|
[bootparam(7)]: https://www.man7.org/linux/man-pages/man7/bootparam.7.html
|