(mds) fix spelling of 'hysteresis'

git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@746 7894878c-1315-0410-8ee3-d5d059ff63e0
2026-11-01 13:20:30 +00:00 · 2000-03-04 16:39:09 +00:00
1 parent f0a4f0713a
commit 0086b4d99e
@@ -60,7 +60,7 @@ two FAN rotation speed sensors, VID lines and some miscellaneous stuff.

 Temperatures are measured in degrees Celcius. An alarm is triggered whenever
 the temperature is above the hot limit, and will continue to be generated
-until the temperature has dropped beneath the hysteris limit. Measurements
+until the temperature has dropped beneath the hysteresis limit. Measurements
 are guaranteed between -40 and +125 degrees. The current temperature
 has a resolution of 0.5 degrees, the limits of 1 degree.

@@ -50,7 +50,7 @@ computer speakers.

 Temperatures are measured in degrees Celcius. An alarm goes off while the
 temperature is above the over temperature limit, and has not yet dropped
-below the hysteris limit. The alarm always reflects the current situation.
+below the hysteresis limit. The alarm always reflects the current situation.
 Measurements are guaranteed between -10 degrees and +110 degrees, with
 a resolution of +-3 degrees.

@@ -39,7 +39,7 @@ The sensor can report alarms through the computer speakers.

 Temperatures are measured in degrees Celcius. An alarm goes off while the
 temperature is above the over temperature limit, and has not yet dropped
-below the hysteris limit. The alarm always reflects the current situation.
+below the hysteresis limit. The alarm always reflects the current situation.
 Measurements are guaranteed between 0 degrees and +110 degrees, with
 a resolution of +-3 degrees.

@@ -38,11 +38,11 @@ Description
 -----------

 The LM75 implements one temperature sensor. Limits can be set through the
-Overtemperature Shutdown register and Hysteris register. Each value can be 
+Overtemperature Shutdown register and Hysteresis register. Each value can be 
 set and read to half-degree accuracy.
 An alarm is issued (usually to a connected LM78) when the temperature
 gets higher then the Overtemperature Shutdown value; it stays on until
-the temperature falls below the Hysteris value.
+the temperature falls below the Hysteresis value.
 All temperatures are in degrees Celcius, and are guaranteed within a 
 range of -55 to +125 degrees.

@@ -60,8 +60,8 @@ seven voltage sensors, VID lines, alarms, and some miscellaneous stuff.

 Temperatures are measured in degrees Celcius. An alarm is triggered once
 when the Overtemperature Shutdown limit is crossed; it is triggered again
-as soon as it drops below the Hysteris value.  A more useful behaviour 
-can be found by setting the Hysteris value to +127 degrees Celcius; in 
+as soon as it drops below the Hysteresis value.  A more useful behaviour 
+can be found by setting the Hysteresis value to +127 degrees Celcius; in 
 this case, alarms are issued during all the time when the actual temperature
 is above the Overtemperature Shutdown value. Measurements are guaranteed
 between -55 and +125 degrees, with a resolution of 1 degree.
@@ -43,7 +43,7 @@ seven voltage sensors, alarms, and some miscellaneous stuff.
 Temperatures are measured in degrees Celcius. There are two sets of limits
 which operate independently. When the HOT Temperature Limit is crossed,
 this will cause an alarm that will be reasserted until the temperature
-drops below the HOT Hysteris. The Overtemperature Shotdown (OS) limits
+drops below the HOT Hysteresis. The Overtemperature Shotdown (OS) limits
 should work in the same way (but this must be checked; the datasheet
 is unclear about this). Measurements are guaranteed between -55 and
 +125 degrees. The current temperature measurement has a resolution of
@@ -41,8 +41,8 @@ sensors, four voltage sensors and alarms.

 Temperatures are measured in degrees Celcius. An alarm is triggered once
 when the Overtemperature Shutdown limit is crossed; it is triggered again
-as soon as it drops below the Hysteris value.  A more useful behaviour 
-can be found by setting the Hysteris value to +127 degrees Celcius; in 
+as soon as it drops below the Hysteresis value.  A more useful behaviour 
+can be found by setting the Hysteresis value to +127 degrees Celcius; in 
 this case, alarms are issued during all the time when the actual temperature
 is above the Overtemperature Shutdown value. Measurements are guaranteed
 between -55 and +125 degrees, with a resolution of 1 degree.
@@ -42,10 +42,10 @@ The THMC50 implements: an internal temperature sensors, support for an
 external diode-type temperature sensor (compatible w/ the diode sensor inside
 many processors), and a controllable fan/analog_out DAC. For the temperature
 sensors, limits can be set through the appropriate Overtemperature Shutdown 
-register and Hysteris register. Each value can be set and read to half-degree 
+register and Hysteresis register. Each value can be set and read to half-degree 
 accuracy.  An alarm is issued (usually to a connected LM78) when the 
 temperature gets higher then the Overtemperature Shutdown value; it stays on 
-until the temperature falls below the Hysteris value. All temperatures are in 
+until the temperature falls below the Hysteresis value. All temperatures are in 
 degrees Celcius, and are guaranteed within a range of -55 to +125 degrees.

 The THMC50 only updates its values each 1.5 seconds; reading it more often