wt/lm-sensors
1
0 Fork 0
mirror of https://github.com/lm-sensors/lm-sensors.git synced 2026-11-08 16:11:26 +00:00
Code Issues Packages Projects Releases Wiki Activity

More cleanups: drop legacy references, sections for drivers not

Browse Source 
yet ported to Linux 2.6, etc.


git-svn-id: http://lm-sensors.org/svn/lm-sensors/branches/lm-sensors-3.0.0@4773 7894878c-1315-0410-8ee3-d5d059ff63e0
This commit is contained in:
Jean Delvare committed 2007-09-05 15:52:56 +00:00
1 parent d577b6eaae
commit 1d05faf18b
1 file changed
+39 -311
Download Patch File Download Diff File Expand all files Collapse all files
etc/sensors.conf.eg
+39 -311
View File
@@ -53,14 +53,12 @@
# These features are defined for each chip in lib/chips.c.
#
# Undefined features will be silently ignored in 'label' and 'compute' lines.
# Undefined features in 'set' lines will result in 'Unknonw feature name'
# Undefined features in 'set' lines will result in 'Unknown feature name'
# when running 'sensors -s'.
#
# Unfortunately, feature names starting with a number must be in
# double quotes or you get "parse error, expecting 'NAME'".
#
# If you have trouble, verify the features in lib/chips.c!!!
#
#
# LABEL LINES
# -----------
@@ -69,10 +67,6 @@
# If no label is specified for a certain feature, the default name
# (ie. 'fan1' for fan1) is used.
#
# If you specify a label for in1, this label is also used for in1_min and
# in1_max, unless they have their own labels declared. There are several
# of these logical groups.
#
# These are as advised in the LM78 and LM79 data sheets, and used on most
# boards we have seen.
#
@@ -88,20 +82,17 @@
# COMPUTE LINES
# -------------
# A compute line describes how to scale a certain feature. There are
# two expressions in it: the first describes how the /proc value must
# two expressions in it: the first describes how the driver value must
# be translated to a user value, the second how a user value must be
# translated to a /proc value. '@' is the value to operate on. You may
# refer to other readable features (like '2 * vid').
# translated to a driver value. '@' is the value to operate on. You may
# refer to other readable features (like 'cpu0_vid * 1.05').
#
# The following operators are valid: + - * / ( ) ^ `
# ^ is e**x and ` is ln(x) (valid in library version 2.0.0 /
# lm_sensors 2.8.0 or higher)
# ^ is e**x and ` is ln(x)
#
# Like for the label statement, there are logical groups here. They are
# sometimes a bit different, though. For example, fan1_div is in the
# logical label group of fan1 (it gets the same label if none is declared
# for it), but it is not in the compute group of fan1 (as it uses a
# completely different system of values).
# Where it makes sense, compute lines are inherited by subfeatures.
# For example, the compute line for 'in0' is automatically applied to
# 'in0_min' and 'in0_max' as well.
#
#
# VOLTAGE COMPUTATION DETAILS
@@ -171,16 +162,12 @@
# compute temp1 @+5,@-5
#
# Sensor type adjustments (certain chips only):
# ...Set temp1 to processor's thermal diode:
# set temp1_type 1 (Winbond chips)
# set temp1_type 3 (IT87xx and MTP008 chips)
#
# ...Set temp1 sensor to 3904 transistor:
# set temp1_type 2 (Winbond chips)
#
# ...Set temp1 to thermistor:
# set temp1_type 3435 (Winbond chips)
# set temp1_type 2 (IT87xx and MTP008 chips)
# set temp1_type 1 # PII/Celeron Diode
# set temp1_type 2 # 3904 transistor
# set temp1_type 3 # thermal diode
# set temp1_type 4 # thermistor
# set temp1_type 5 # AMD AMDSI
# set temp1_type 6 # Intel PECI
#
# Often, a temperature sensor is disconnected; disable it with an ignore line:
# ignore temp3
@@ -203,9 +190,9 @@
# set temp1_max 40
# set temp1_max_hyst 37
#
# Think of tempx_over as 'alarm set' and tempx_hyst as 'alarm clear'
# thresholds. In most cases the 'over' value should be higher than
# the 'hyst' value by several degrees.
# Think of tempx_max as 'alarm set' and tempx_max_hyst as 'alarm clear'
# thresholds. In most cases the 'max' value should be higher than
# the 'max_hyst' value by several degrees.
#
# All the set statements from this file are commented out by default.
# The reason is that the proper limits are highly system-dependent,
@@ -216,11 +203,10 @@
#
# IGNORE LINES
# ------------
# Ignore statements tell certain features are not wanted. User programs can
# still read them if they really want, though; this is just an advisory
# marking. 'in0' would also invalidate 'in0_max' and 'in0_min'.
# Ignore statements tell certain features are not wanted. As with compute
# statements, 'ignore in0' would also invalidate 'in0_max' and 'in0_min'.
# 'ignore' does not disable anything in the actual sensor chip; it
# simply advises the user program to not access that data.
# simply prevents the user program from accessing that data.
#
# ignore in0
#
@@ -373,8 +359,7 @@ chip "lm78-*" "lm79-*" "w83781d-*"
chip "lm75-*"
# Most boards don't need scaling. Following is
# for the Asus TX97-E. If it doesn't work for you, feel free to complain.
# Most boards don't need scaling. Following is for the Asus TX97-E.
# compute temp1 @*2.0, @/2.0
# Examples for temperature limits
@@ -439,7 +424,6 @@ chip "sis5595-*"
# compute temp1 ((X * ((1.20 * @) - 62.77)) - Y), ...
# examples for sis5595 temperature limits;
# for sis5595, temp_hyst is really the low limit, not a hysteresis value
# set temp1_max 40
# set temp1_max_hyst 37
@@ -661,9 +645,6 @@ chip "w83627thf-*" "w83637hf-*"
# Note that in1 (+12V) is the usual in4, and in4 (-12V) is the usual in5.
# Data sheet is obviously wrong for in4, the usual formula should work.
# No in5 nor in6.
# sensors doesn't need the ignore lines but sensord does...
ignore in5
ignore in6
label in0 "VCore"
label in1 "+12V"
@@ -939,9 +920,7 @@ chip "gl520sm-*"
# The GL520SM has two application modes. In mode 1 it has two thermistor
# inputs, in mode 2 it has only one and an extra (negative) voltage input.
# The mode is supposed to be set properly by your BIOS so you should not
# need to change it. You can force it below if really needed though.
# Note that this means that you have either temp2 or vin4 but never both
# at the same time.
# need to change it. Note that you have either temp2 or in4, not both.
label in0 "+5V"
label in1 "+3.3V"
@@ -975,8 +954,7 @@ chip "gl520sm-*"
chip "lm80-*"
# The values below should be correct if you own a qdi BX (brilliant1)
# mainboard. If not, please contact us, so we can figure out better readings.
# Many thanks go to Peter T. Breuer <ptb@it.uc3m.es> for helping us figure
# mainboard. Many thanks go to Peter T. Breuer for helping us figure
# out how to handle the LM80.
# For positive voltages (in0..in4), two resistors are used, with the following
@@ -1034,10 +1012,10 @@ chip "lm80-*"
# All 4 of these limits apply to the single temperature sensor.
# "crit" may or may not do anything on your motherboard but it should
# be set higher than the "max" thresholds.
# set temp1_max_hyst 45
# set temp1_max 52
# set temp1_max_hyst 45
# set temp1_max 52
# set temp1_crit_hyst 57
# set temp1_crit 62
# set temp1_crit 62
chip "via686a-*"
@@ -1045,17 +1023,16 @@ chip "via686a-*"
# VIA is very specific about the voltage sensor inputs, and our labels
# reflect what they say. Unfortunately, they are not at all specific about
# how to convert any of the register values to real units. Fortunately,
# Jonathan Yew <j.teh@iname.com> and Alex van Kaam <darkside@chello.nl>
# came through with some data for temp conversion and formulae for voltage
# conversion. However, the conversions should be regarded as our best guess-
# YMMV.
# Jonathan Yew and Alex van Kaam came through with some data for temp
# conversion and formulae for voltage conversion. However, the conversions
# should be regarded as our best guess - YMMV.
# On the Tyan S1598, the 2.5V sensor reads 0 and is not displayed in the BIOS.
# Linas Vepstas <linas@linas.org> reports that this sensor shows nothing of
# Linas Vepstas reports that this sensor shows nothing of
# interest on the Abit KA7 (Athlon), and is also not displayed in the BIOS.
# Likewise, Johannes Drechsel-Burkhard <jdb@chello.at> reports that this
# Likewise, Johannes Drechsel-Burkhard reports that this
# sensor is unavailable in the BIOS of his MSI K7T Pro (Thunderbird). So,
# if you have one of these boards you may want to uncomment the 'ignore 2.5V'
# if you have one of these boards you may want to uncomment the 'ignore in1'
# line below.
label in0 "CPU core"
@@ -1075,7 +1052,7 @@ chip "via686a-*"
# different from temp1 & temp2 (as noted above, VIA has not provided
# conversion info). So, you may wish to 'ignore temp3'.
# Johannes Drechsel-Burkhard <jdb@chello.at> notes that on his MSI K7T Pro,
# Johannes Drechsel-Burkhard notes that on his MSI K7T Pro,
# temp1 is the CPU temp and temp2 is the SYS temp. Hugo van der Merwe notes
# the same for his Gigabyte GA-7DXC, Olivier Martin for his Gigabyte
# GA-7ZM and Patrick Thomson for his Chaintech CT-5ATA.
@@ -1102,9 +1079,9 @@ chip "via686a-*"
# set in4_min 12 * 0.9
# set in4_max 12 * 1.1
# Set your temp limits here. Remember, 'tempX_over' is the temp at which an
# alarm is triggered, and 'tempX_hyst' is the temp at which an alarm turns off.
# Setting tempX_hyst to a few degrees below the corresponding tempX_over
# Set your temp limits here. Remember, 'tempX_max' is the temp at which an
# alarm is triggered, and 'tempX_max_hyst' is the temp at which an alarm turns off.
# Setting tempX_max_hyst to a few degrees below the corresponding tempX_max
# prevents an oscillation between alarm on and off states. This kind of
# oscillation is known as hyteresis, thus the name. (You typically get the
# most serious and troublesome hysteresis when a sensor triggers something to
@@ -1125,101 +1102,6 @@ chip "via686a-*"
#set fan2_min 5000
chip "mtp008-*"
# The values below should be correct if you own a Tyan S1834D motherboard.
# If not, please contact us, so we can figure out better readings.
# FOR TYAN S2510 SEE END OF THIS SECTION.
# For positive voltages outside the 0..4.09V range (in2..in4), two resistors
# are used, with the following formula (R1,R2: resistor values, Vs: read
# voltage, Vin: pin voltage)
# Vin = Vs * (R2 / (R1 + R2))
# For negative voltages (in5) two resistors are used, with the following
# formula (R3,R4: resistor values, Vs: read voltage, Vin: pin voltage)
# Vin = ((4.096 - Vs) * (R3 / (R3 + R4))) + Vs
# Here are the official MTP008 data sheet values:
# Vs R1,R3 R2,R4 Vin
# +12.0 28000 10000 +3.16
# -12.0 232000 56000 +0.96
# -5.0 120000 56000 +1.20
label in0 "VCore1"
label in1 "+3.3V"
label in2 "+12V"
label in3 "Vcore2"
ignore in4
label in5 "-12V"
label in6 "Vtt"
label fan1 "CPU1 Fan"
label fan2 "CPU2 Fan"
label fan3 "fan3"
label temp1 "CPU1 Temp"
label temp2 "CPU2 Temp"
ignore temp3
compute in2 @ * 38 / 10, @ * 10 / 38
compute in5 (@ * 36 - 118.61) / 7, (118.61 + 7 * @) / 36
# examples for temperature limits
# set temp1_max 40
# set temp1_max_hyst 37
# set temp2_max 52
# set temp2_max_hyst 47
# set temp3_max 52
# set temp3_max_hyst 47
# End of standard mtp008 configuration
# TYAN S2510 INFORMATION
# This motherboard has two mtp008's which are hooked up differently,
# so they must be configured separately.
# For this motherboard, COMMENT OUT the above mtp008 section and
# UNCOMMENT the following two sections.
#
#chip "mtp008-i2c-*-2c"
# label in0 "VCore1"
# set in0_min 1.60
# set in0_max 1.80
# label in1 "+3.3V"
# label in2 "+12V"
# label in3 "Vcore2"
# set in3_min 1.60
# set in3_max 1.80
# ignore in4
# label in5 "-12V"
# label in6 "Vtt"
# label fan1 "CPU1 Fan"
# label fan2 "CPU2 Fan"
# label fan3 "fan3"
# label temp1 "CPU1 Temp"
# label temp2 "CPU2 Temp"
# ignore temp3
# compute in2 @ * 38 / 10, @ * 10 / 38
# compute in5 (@ * 36 - 118.61) / 7, (118.61 + 7 * @) / 36
#
#chip "mtp008-i2c-*-2e"
# ignore in0
# label in1 "+3.3V"
# ignore in2
# label in3 "+5V"
# set in3_min 4.50
# set in3_max 5.50
# ignore in4
# label in5 "+3.3V"
# ignore in6
# label fan1 "fan4"
# label fan2 "fan5"
# label fan3 "fan6"
# ignore temp1
# label temp2 "MB Temp"
# set temp2_max 52
# set temp2_max_hyst 47
# ignore temp3
chip "adm1025-*" "ne1619-*"
# The ADM1025 has integrated scaling resistors, rather
@@ -1280,23 +1162,6 @@ chip "lm87-*"
# motherboard connections match these labels, and that the
# driver computations are correct. Therefore they do not need to
# be overridden here.
#
# Note: AIN1 (-12?), AIN2 (-5?) and temp3 require changing
# #defines in the driver and recompiling!!!
# This does not apply to the Linux 2.6 driver.
#
# This chip has non-standard entries in lib/chips.c so
# the feature names are quite different from other chips.
# For this chip, libsensors anticipates the correct labeling.
# This is great if it's correct but makes it a little more
# difficult if you want to change it.
#
# This may not have been a good idea, so it may be changed in the future.
# Here is an entry with everything commented out so you can
# uncomment the appropriate line if you want to change it.
#
# Warning - feature names starting with a number must be enclosed
# with double quotes.
label in0 "+2.5V"
label in1 "VCore"
@@ -1346,86 +1211,16 @@ chip "lm87-*"
# set temp3_max 70
# LM87 AIN1 and AIN2 Section
# As described above, the driver must be recompiled to use either or
# both of these. -12 and -5 may be reversed on your board, this is
# -12 and -5 may be reversed on your board, this is
# just a guess, the datasheet gives no guidance.
# Note that the Linux 2.6 driver needs no recompilation, it'll read the
# configuration from the chip.
# label in6 "-12V"
# label in7 "-5V"
# compute in6 (7.50 * @) - 21.45 , (@ + 21.45) / 7.50
# compute in7 (4.05 * @) - 10.07 , (@ + 10.07) / 4.05
# set in6_min -12 * 0.95
# set in7_min -5 * 0.95
# set in6_max -12 * 1.05
# set in7_max -5 * 1.05
# compute in6 (7.50 * @) - 21.45 , (@ + 21.45) / 7.50
# compute in7 (4.05 * @) - 10.07 , (@ + 10.07) / 4.05
chip "adm9240-*" "ds1780-*" "lm81-*"
#
# These chips have non-standard entries in lib/chips.c so
# the feature names are quite different from other chips.
# For these chips, libsensors anticipates the correct labeling.
# This is great if it's correct but makes it a little more
# difficult if you want to change it.
#
# This may not have been a good idea, so it may be changed in the future.
# Here is an entry with everything commented out so you can
# uncomment the appropriate line if you want to change it.
#
# Warning - feature names starting with a number must be enclosed
# with double quotes.
#
# label in0 "xxx"
# label in1 "xxx"
# label in2 "xxx"
# label in3 "xxx"
# label in4 "xxx"
# label in5 "xxx"
# label fan1 "xxx"
# label fan2 "xxx"
# label temp1 "xxx"
#
# set in1_min xxx
# set in0_min xxx
# set in2_min xxx
# set in3_min xxx
# set in4_min xxx
# set in5_min xxx
#
# set in1_max xxx
# set in0_max xxx
# set in2_max xxx
# set in3_max xxx
# set in4_max xxx
# set in5_max xxx
#
# set fan1_div xxx Note: do not uncomment with kernel 2.6 driver
# set fan2_div xxx Note: do not uncomment with kernel 2.6 driver
# set fan1_min xxx
# set fan2_min xxx
# set temp1_max_hyst xxx
# set temp1_max xxx
# compute in0 xxx
# compute in1 xxx
# compute in2 xxx
# compute in3 xxx
# compute in4 xxx
# compute in5 xxx
# compute temp1 xxx
chip "adm1024-*"
#
# These settings work for me, adjust for your system
#
label fan1 "CPU1 fan"
label fan2 "CPU2 fan"
label temp1 "SYS Temp"
label temp2 "CPU2 Temp"
label temp3 "CPU1 Temp"
ignore in0 # This register is also used for temp3
ignore in1
ignore in5
chip "it87-*" "it8712-*"
@@ -1510,7 +1305,6 @@ chip "it87-*" "it8712-*"
# Important - if your temperature readings are completely whacky
# you probably need to change the sensor type.
# Adujst and uncomment the appropriate lines below.
# The old method (modprobe it87 temp_type=0xXX) is no longer supported.
#
# 2 = thermistor; 3 = thermal diode; 0 = unused
# set temp1_type 3
@@ -1548,55 +1342,6 @@ chip "it87-*" "it8712-*"
# ignore fan3
# set fan3_min 3000
# The following is for the Inside Technologies 786LCD which uses either a
# IT8705F or a SIS950 for monitoring with the SIS630.
#
# delete or comment out above it87 section and uncomment the following.
#chip "it87-*"
# label in0 "VCore 1"
# label in1 "VCore 2"
# label in2 "+3.3V"
# label in3 "+5V"
# label in4 "+12V"
# label in5 "3.3 Stdby"
# label in6 "-12V"
# label in7 "Stdby"
# label in8 "VBat"
# in0 will depend on your processor VID value, set to voltage specified in
# bios setup screen
# set in0_min 1.7 * 0.95
# set in0_max 1.7 * 1.05
# set in1_min 2.4
# set in1_max 2.6
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# set in3_min 5.0 * 0.95
# set in3_max 5.0 * 1.05
# +- 12V are very poor tolerance on this board. Verified with voltmeter
# set in4_min 12 * 0.90
# set in4_max 12 * 1.10
# set in5_min 3.3 * 0.95
# set in5_max 3.3 * 1.05
# set in6_max -12 * 0.90
# set in6_min -12 * 1.10
# set in7_min 5 * 0.95
# set in7_max 5 * 1.05
# vid not monitored by IT8705F
# ignore cpu0_vid
# compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
# compute in4 ((30/10) +1)*@ , @/((30/10) +1)
# compute in6 (1+232/56)*@ - 4.096*232/56, (@ + 4.096*232/56)/(1+232/56)
# compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)
# Temperature
# label temp1 "CPU Temp"
# ignore temp2
# ignore temp3
# Fans
# set fan1_min 3000
# ignore fan2
# ignore fan3
chip "it8716-*"
@@ -2046,7 +1791,6 @@ chip "vt8231-*"
# Thermistor calculations
# 3435 is the thermistor beta, 2.2 is the reference voltage.
# '^' is the e**x operator; '`' is the ln(x) operator
# (valid in library version 1.4.0 / lm_sensors 2.7.1 or higher)
# This assumes that the thermistor forms a resistor divider with a resistor
# equal to its nominal value at 25 degrees C.
@@ -2063,24 +1807,11 @@ chip "vt8231-*"
# set fan1_min 3000
# set fan2_min 3000
chip "bmc-*"
#
# You should not need compute lines here, the driver will
# do all the conversions.
# For label lines, copy from syslog/dmesg when the bmcsensors
# module is inserted.
#
# for example:
# label temp1 "Ambient Temp"
chip "smsc47m1-*"
# SMSC LPC47M10x, LPC47M13x, LPC47M14x and LPC47B27x chips
# We don't set the fan mins by default anymore because they may not exist
# when using the Linux 2.6 driver (since we respect the original chip
# configuration).
# set fan1_min 3000
# set fan2_min 3000
@@ -2430,9 +2161,6 @@ chip "w83627ehf-*" "w83627dhg-*"
label in7 "VSB"
label in8 "VBAT"
# The W83627DHG has no in9, uncomment the following line
# ignore in9
# +12V is in1 and +5V is in6 as recommended by datasheet
compute in1 @*(1+(56/10)), @/(1+(56/10))
compute in6 @*(1+(22/10)), @/(1+(22/10))