mirror of
https://github.com/lm-sensors/lm-sensors.git
synced 2026-11-19 19:40:49 +00:00
Update pwmconfig manual page.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/branches/lm-sensors-3.0.0@5344 7894878c-1315-0410-8ee3-d5d059ff63e0
This commit is contained in:
1 parent
f7ccb96a7c
commit
66130a9630
2 files changed
+38
-12
No files matched your search
@@ -14,6 +14,7 @@ SVN-HEAD
|
||||
Skip MINSTOP and MINSTART tests if fan can't stop
|
||||
Change default for MINTEMP from 0 to 20 degrees C
|
||||
Add support for attributes in the hwmon class device (#2260)
|
||||
Update manual page
|
||||
sensors-detect: Add Intel SCH (bus) support
|
||||
Add SMSC EMC6D103 support
|
||||
Improve MAX6657, MAX6658, MAX6659 detection
|
||||
|
||||
+37
-12
@@ -1,30 +1,55 @@
|
||||
.TH PWMCONFIG 8 "January 27, 2005" "lm-sensors 3"
|
||||
.TH PWMCONFIG 8 "September 28, 2008" "lm-sensors 3"
|
||||
.SH NAME
|
||||
pwmconfig \- tests the PWM outputs of sensors and configures fancontrol
|
||||
|
||||
.SH SYNOPSIS
|
||||
.B pwmconfig
|
||||
|
||||
.SH WARNING
|
||||
\fBpwmconfig\fR will attempt to stop your fans, one at a time, for
|
||||
approximately 5 seconds each. This may cause your processor
|
||||
temperature to rise. Verify that all fans are running at normal speed
|
||||
after this program has exited.
|
||||
\fBpwmconfig\fR does its best to check that the fans are spinning when
|
||||
they are supposed to, but due to the diversity of available
|
||||
motherboards and fans, it shouldn't be blindly trusted. Always verify
|
||||
by yourself.
|
||||
|
||||
It is strongly recommended to run \fBpwmconfig\fR at a time when there
|
||||
is no significant system load, to minimize the risk of overheating.
|
||||
|
||||
.SH DESCRIPTION
|
||||
.B pwmconfig
|
||||
searches your sensors for pulse width modulation (PWM)
|
||||
controls, and test each one to see if it controls a fan on
|
||||
controls, and tests each one to see if it controls a fan on
|
||||
your motherboard. Note that many motherboards do not have PWM
|
||||
circuitry installed, even if your sensor chip supports PWM.
|
||||
|
||||
It attempts to briefly stop each fan using the PWM controls. It then
|
||||
attempts to restore each fan to full speed after testing. However, it
|
||||
is \fBvery important\fP that you physically verify that the fans have
|
||||
been returned to full speed after the program has completed.
|
||||
When a connection is established between a PWM control and a fan,
|
||||
\fBpwmconfig\fR can generate a detailed correlation, to show how a
|
||||
given fan is responding to various PWM duty cycles.
|
||||
|
||||
.SH WARNING
|
||||
This program will stop your fans, one at a time, for approximately 5 seconds each.
|
||||
This may cause your processor temperature to rise. Verify that all fans are running
|
||||
at normal speed after this program has exited.
|
||||
Lastly, \fBpwmconfig\fR will enter in \fBfancontrol\fR configuration
|
||||
mode (unless you decide to skip that part.) In this mode, you are
|
||||
invited to enter several parameters which will determine how the
|
||||
\fBfancontrol\fR daemon regulates the speed of one or more fans in
|
||||
your system based on temperature measurements. In particular, you will
|
||||
have the opportunity to establish mappings between fans and
|
||||
temperature inputs, define the temperature range over which the speed
|
||||
of the fan should be adjusted dynamically, the minimum speed at which
|
||||
the fan should spin, etc. See fancontrol(8) for additional
|
||||
information.
|
||||
|
||||
.SH BUGS
|
||||
The term "PWM" is used because most fan control systems in computers
|
||||
are based on pulse width modulation. Some motherboards however use DC
|
||||
variation instead. So, the term "PWM" should be seen as a generic term
|
||||
for "fan speed control", regardless of the actual method used.
|
||||
|
||||
.SH SEE ALSO
|
||||
fancontrol(8), sensors(1).
|
||||
|
||||
.SH AUTHOR
|
||||
.SH AUTHORS
|
||||
.PP
|
||||
Marius Reiner <marius.reiner@hdev.de>
|
||||
Marius Reiner <marius.reiner@hdev.de>,
|
||||
Jean Delvare <khali@linux-fr.org>
|
||||
Reference in new issue
Block a user