give w83783s its own section to avoid "unknown feature name"

ticket 1281


git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1785 7894878c-1315-0410-8ee3-d5d059ff63e0

etc/sensors.conf.eg

@@ -383,7 +383,7 @@ chip "sis5595-*"
 #    set temp_over 40
 #    set temp_hyst 37
 
-chip "w83782d-*" "w83783s-*" "w83627hf-*"
+chip "w83782d-*" "w83627hf-*"
 
 # Same as above for w83781d except that in5 and in6 are computed differently.
 # Rather than an internal inverting op amp, the 82d/83s use standard positive
@@ -450,6 +450,60 @@ chip "w83782d-*" "w83783s-*" "w83627hf-*"
 #    set temp3_hyst 47
 
 
+chip "w83783s-*"
+
+# Same as above for w83781d except that in5 and in6 are computed differently.
+# Rather than an internal inverting op amp, the 82d/83s use standard positive
+# inputs and the negative voltages are level shifted by a 3.6V reference.
+# The math is convoluted, so we hope that your motherboard
+# uses the recommended resistor values.
+
+    label in0 "VCore 1"
+    label in2 "+3.3V"
+    label in3 "+5V"
+    label in4 "+12V"
+    label in5 "-12V"
+    label in6 "-5V"
+
+    compute in3 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)
+    compute in4 ((28/10)+1)*@  ,  @/((28/10)+1)
+    compute in5 (5.14 * @) - 14.91  ,  (@ + 14.91) / 5.14
+    compute in6 (3.14 * @) -  7.71  ,  (@ +  7.71) / 3.14
+
+# adjust this if your vid is wrong; see doc/vid
+#   set vrm 9.0
+
+# set limits to  5% for the critical voltages
+# set limits to 10% for the non-critical voltages
+# set limits to 20% for the battery voltage
+
+    set in0_min vid*0.95
+    set in0_max vid*1.05
+    set in2_min 3.3 * 0.95
+    set in2_max 3.3 * 1.05
+    set in3_min 5.0 * 0.95
+    set in3_max 5.0 * 1.05
+    set in4_min 12 * 0.90
+    set in4_max 12 * 1.10
+    set in5_max -12 * 0.90
+    set in5_min -12 * 1.10
+    set in6_max -5 * 0.95
+    set in6_min -5 * 1.05
+
+# set up sensor types (thermistor is default)
+# 1 = PII/Celeron Diode; 2 = 3904 transistor;
+# 3435 = thermistor with Beta = 3435
+# If temperature changes very little, try 1 or 2.
+#   set sensor1 1
+#   set sensor2 2
+
+# examples for temperature limits
+#    set temp1_over 40
+#    set temp1_hyst 37
+#    set temp2_over 52
+#    set temp2_hyst 47
+
+
 chip "w83697hf-*"
 
 # Same as above for w83781d except that in5 and in6 are computed differently.