add documentation entries for editticket, readticket, maxilife,

and matorb display programs.


git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@988 7894878c-1315-0410-8ee3-d5d059ff63e0

doc/progs

@@ -2,25 +2,36 @@ This is a list of additional programs, that may or may not be installed by
 `make install', and that usually can be found in the `prog' directory of
 this package.
 
+
+* doc/developers/editticket (written in shell, not installed)
+  Calls netscape to edit a specific support ticket.
+
+* doc/developers/readticket (written in shell, not installed)
+  Calls netscape to read a specific support ticket.
+
 * prog/config/grab_busses.sh (written in bash and awk, not installed)
   This program helps you generate the `bus' statements for your configuration
   file. It read /proc/bus/i2c (or the file specified on the command-line),
   and prints to stdout `bus' statements reflecting the currently detected
   adapters.
+
 * prog/daemon/healthd.sh (written in bash, not installed)
   An example of a very simple hardware health monitoring daemon.
-* prog/detect/sensors-detect (written in Perl, installed by 'make install')
-  This program tries to detect the available SMBus adapters and the chips
-  connected to them and/or the ISA bus. It also generates modprobe lines
-  and module options. This program is interactive and will ask you about
-  all information it needs.
+
 * prog/detect/i2cdetect (written in C, not installed)
   This program scans your complete I2C or SMBus adapter for connected devices.
   Not all devices can be detected in this way, though; and it may hang your
   bus. Syntax:
     ./i2cdetect 0
-  Here the '0' stands for i2c-0 (check /proc/bus/i2c to find out which bus
-  you need).
+  Here the '0' stands for the bus number (run i2cdetect with no arguments 
+  to list all installed busses).
+
+* prog/detect/sensors-detect (written in Perl, installed by 'make install')
+  This program tries to detect the available SMBus adapters and the chips
+  connected to them and/or the ISA bus. It also generates modprobe lines
+  and module options. This program is interactive and will ask you about
+  all information it needs.
+
 * prog/doc/doc-features.pl (written in Perl, not installed)
   This program is used to help us generate driver documentation; it scans
   some C source programs to do this. Syntax:
@@ -28,38 +39,61 @@ this package.
   BASE is the path to the base directory of the lm_sensors tree
   PREFIX is one of more prefixes of chips you want documented; if left out,
   all chips are documented.
+
 * prog/doc/doc-insmod.pl (written in Perl, not installed)
   This program is used to help us generate driver documentation; it reads
   all module information and outputs insmod parameter information. Syntax:
     ./doc-insmod.pl DRIVER
+
 * prog/dump/i2cdump (written in C, not installed)
   This program helps to dump the registers of a I2C device that understands
-  the 'byte data' or 'word data' SMBus protocols. Usual syntax:
+  the 'byte data' or 'word data' and block read SMBus protocols.
+  Usual syntax:
     ./i2cdump 0 0x49 b
-  Here the '0' stands for i2c-0 (check /proc/bus/i2c to find out which bus
-  you need), '0x49' is the device address, and 'b' or 'w' stands for byte
+  Here the '0' stands for the bus number (run i2cdump with no arguments 
+  to list all installed busses).
+  0x49' is the device address, and 'b' or 'w' stands for byte
   or word data.
+
 * prog/dump/isadump (written in C, not installed)
   This program helps to dump the registers of LM78-like chips, or more
   exactly, chips which use an I/O-port for its address and one as its
   data register. Usual syntax: 
      ./isadump 0x295 0x296
+
 * prog/eeprom/decode-dimms.pl (written in Perl 5, not installed)
   This program decodes the information generated by the `eeprom.o' module.
   It will only work for the installed eeprom module from the src/ directory,
   not for the old one in the i2c/drivers/ directory.
+
+* prog/hotplug/m7101.o (kernel module, not installed)
+  An experimental kernel module to enable the Acer Labs 7101 PCI device.
+  See prog/hotplug/README for details.
+
+* prog/matorb/displayit.pl (written in Perl, not installed)
+  A simple Perl script to display a 'screen' on a Matrix Orbital Display.
+
+* prog/maxilife/sysinfo.sh (written in shell, not installed)
+  Write system information to the HP Maxilife LCD display using writelcd.sh.
+
+* prog/maxilife/writelcd.sh (written in shell, not installed)
+  Write a string to the HP Maxilife LCD display.
+
 * prog/mkdev/mkdev.sh (written in bash, not installed)
   This script creates the /dev/i2c-* files. Please check the source before
   you run it, as you may need to set some variables first.
+
 * prog/sensord/sensord (written in C, installed by `make install-prog-sensord')
   This daemon can be used to periodically log sensor readings from
   the sensors hardware to syslog, and to alert (using syslog level ALERT)
   when a sensor alarm is signalled; for example, if a fan fails, a temperature
   limit is exceeded, etc.
+
 * prog/sensors/sensors (written in C, installed by `make install')
   This pretty-prints the information provided by the modules. It is a normal
-  console application, using stdin and stdout. It is essential, because
+  console application, using stdout. It is essential, because
   unlike the raw /proc/sys/dev/sensors/*/* files, it takes your configuration
   file into account.
-* prog/xeon/decode-xeon.pl (written in perl, not installed)
+
+* prog/xeon/decode-xeon.pl (written in Perl, not installed)
   ID ROM data decoding for Xeon processors.