Add section for lm75 in sensors.conf.eg

Complete the lm78 section in sensors.conf.eg


git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1588 7894878c-1315-0410-8ee3-d5d059ff63e0
This commit is contained in:
Jean Delvare committed 2002-11-08 12:06:53 +00:00
1 parent fcd4e835b0
commit cca8422639
2 files changed
+120 -94

No files matched your search

+2 -1
View File
@@ -26,11 +26,12 @@ ask CVS about it:
File doc/chips/maxilife: Add license, parameters, features
File doc/chips/smartbatt: Complete rewrite
File doc/chips/vt8231: Add license, parameters
File sensors.conf.eg: Add section for lm75; complete the lm78 section
Library: Add support for MC1066; add multiple VRM version support for lm87;
enhance adm1023 support
Makefile: Take kernel source location from /lib/modules/x.x.x/build
Module adm1021: Add support for MC1066
Module dmi_scan: Rename symbol duplicated in kernel; Apply fixes from
Module dmi_scan: Rename symbol duplicated in kernel; apply fixes from
kernel 2.5.43
Module gl518sm: Iterate allowed only for rev 0x00
Module i2c-amd756: Configure base address for nForce support;
+118 -93
View File
@@ -31,7 +31,7 @@
#
# CHIP LINES
# ----------
# A 'chip' line specifies what the following 'label', 'compute', 'set' and
# A 'chip' line specifies what the following 'label', 'compute', 'set' and
# 'ignore' lines refer to. In this case, until the
# next 'chip' line, everything refers to all lm78, lm78-j and lm79
# chips. Other examples are *-isa-* for everything on the ISA bus, and
@@ -83,8 +83,8 @@
# label in4 "+12V"
# label in5 "-12V"
# label in6 "-5V"
#
#
#
#
# COMPUTE LINES
# -------------
# A compute line describes how to scale a certain feature. There are
@@ -138,7 +138,7 @@
# compute in6 -(100/60)*@ , -@/(100/60)
#
# On almost any mainboard we have seen, the Winbond compute values lead to
# much better results, though.
# much better results, though.
#
# Vs R1,Rin R2,Rf Vin
# in4 +12.0 28 10 +3.00
@@ -166,8 +166,8 @@
#
# set in0_max vid*1.05
# set in0_min vid*0.95
# set temp1_over 40
# set temp1_hyst 37
# set temp1_over 40
# set temp1_hyst 37
#
# Think of tempx_over as 'alarm set' and tempx_hyst as 'alarm clear'
# thresholds. In most cases the 'over' value should be higher than
@@ -254,7 +254,7 @@ chip "lm78-*" "lm78-j-*" "lm79-*" "w83781d-*"
# compute in6 -(100/60)*@ , -@/(100/60)
#
# On almost any mainboard we have seen, the Winbond compute values lead to
# much better results, though.
# much better results, though.
#
# Vs R1,Rin R2,Rf Vin
# in4 +12.0 28 10 +3.00
@@ -285,17 +285,42 @@ chip "lm78-*" "lm78-j-*" "lm79-*" "w83781d-*"
set in6_max -5 * 0.95
set in6_min -5 * 1.05
# examples for lm78, lm78j, lm79 temperature limits;
# set temp_over 40
# set temp_hyst 37
# Examples for lm78, lm78j, lm79 temperature limits
# set temp_over 40
# set temp_hyst 37
# examples for w83781d temperature limits
# set temp1_over 40
# set temp1_hyst 37
# set temp2_over 52
# set temp2_hyst 47
# set temp3_over 52
# set temp3_hyst 47
# Examples for w83781d temperature limits
# set temp1_over 40
# set temp1_hyst 37
# set temp2_over 52
# set temp2_hyst 47
# set temp3_over 52
# set temp3_hyst 47
# Ignore fans you don't actually have
# ignore fan1
# ignore fan2
# ignore fan3
# In case a lm78 is used together with a lm75, the lm78 temp sensor will
# generally show the M/B temperature while the lm75 temp sensor will show
# the CPU temperature.
# label temp "M/B Temp"
chip "lm75-*"
# For the Asus TX97-E. If it doesn't work for you, feel free to complain.
compute temp @*2.0, @/2.0
# Examples for temperature limits
# set temp_over 70
# set temp_hyst 65
# In case a lm75 is used together with a lm78, the lm78 temp sensor will
# generally show the M/B temperature while the lm75 temp sensor will show
# the CPU temperature.
# label temp "CPU Temp"
chip "sis5595-*"
@@ -351,8 +376,8 @@ chip "sis5595-*"
# examples for sis5595 temperature limits;
# for sis5595, temp_hyst is really the low limit, not a hysteresis value
# set temp_over 40
# set temp_hyst 37
# set temp_over 40
# set temp_hyst 37
chip "w83782d-*" "w83783s-*" "w83627hf-*"
@@ -413,12 +438,12 @@ chip "w83782d-*" "w83783s-*" "w83627hf-*"
# set sensor3 3435
# examples for temperature limits
# set temp1_over 40
# set temp1_hyst 37
# set temp2_over 52
# set temp2_hyst 47
# set temp3_over 52
# set temp3_hyst 47
# set temp1_over 40
# set temp1_hyst 37
# set temp2_over 52
# set temp2_hyst 47
# set temp3_over 52
# set temp3_hyst 47
chip "w83697hf-*"
@@ -477,12 +502,12 @@ chip "w83697hf-*"
# set sensor3 3435
# examples for temperature limits
# set temp1_over 40
# set temp1_hyst 37
# set temp2_over 52
# set temp2_hyst 47
# set temp3_over 52
# set temp3_hyst 47
# set temp1_over 40
# set temp1_hyst 37
# set temp2_over 52
# set temp2_hyst 47
# set temp3_over 52
# set temp3_hyst 47
chip "as99127f-*"
@@ -534,12 +559,12 @@ chip "as99127f-*"
set in6_min -5 * 1.05
# examples for temperature limits
# set temp1_over 40
# set temp1_hyst 37
# set temp2_over 52
# set temp2_hyst 47
# set temp3_over 52
# set temp3_hyst 47
# set temp1_over 40
# set temp1_hyst 37
# set temp2_over 52
# set temp2_hyst 47
# set temp3_over 52
# set temp3_hyst 47
chip "gl518sm-*"
@@ -556,7 +581,7 @@ chip "gl518sm-*"
label vin2 "+12V"
label vin3 "Vcore"
# vin2 depends on external resistors (4,7k and 15k assumed here)
# vin2 depends on external resistors (4,7k and 15k assumed here)
# vin1 and vin3 require no scaling
compute vin2 (197/47)*@ , @/(197/47)
@@ -586,10 +611,10 @@ chip "gl520sm-*"
# vin1 and vin3 require no scaling
# vin2 depends on external resistors (4,7k and 15k assumed)
# vin4 = ((R1+R2)/R2)*@ - (R1/R2)*vdd
#
# -12 --| R1 |---t---| R2 |-- +5
# -12 --| R1 |---t---| R2 |-- +5
# |
# vin4
#
@@ -609,7 +634,7 @@ chip "gl520sm-*"
chip "lm80-*"
# The values below should be correct if you own a qdi BX (brilliant1)
# mainboard. If not, please contact us, so we can figure out better readings.
# Many thanks go to Peter T. Breuer <ptb@it.uc3m.es> for helping us figure
@@ -619,9 +644,9 @@ chip "lm80-*"
# formula (R1,R2: resistor values, Vs: read voltage, Vin: pin voltage)
# R1 = R2 * (Vs/Vin - 1)
# For negative voltages (in5, in6) two resistors are used, with the following
# formula (R3,R4: resistor values, Vs: read voltage, Vin: pin voltage,
# formula (R3,R4: resistor values, Vs: read voltage, Vin: pin voltage,
# V5: +5V)
# R3 = R4 * (Vs - Vin) / (Vin - V5)
# R3 = R4 * (Vs - Vin) / (Vin - V5)
# Here are the official LM78 and LM79 data sheet values.
# Vs R1,R3 R2,R4 Vin
@@ -677,9 +702,9 @@ chip "lm80-*"
# Note that the /proc file 'temp" also has five entries instead of
# the usual three.
# set temp_hot_hyst 45
# set temp_hot_max 52
# set temp_os_hyst 57
# set temp_os_max 62
# set temp_hot_max 52
# set temp_os_hyst 57
# set temp_os_max 62
chip "maxilife-cg-*" "maxilife-co-*" "maxilife-as-*"
@@ -688,7 +713,7 @@ chip "maxilife-cg-*" "maxilife-co-*" "maxilife-as-*"
label fan2 "PCI Fan"
label fan3 "CPU Fan"
ignore fan4
label temp2 "PCI Temp"
label temp4 "HDD Temp"
label temp5 "CPU Temp"
@@ -697,7 +722,7 @@ chip "maxilife-cg-*" "maxilife-co-*" "maxilife-as-*"
label vid1 "V+12"
ignore vid5
# vid1 need to be scaled by 6.337 other voltages
# vid1 need to be scaled by 6.337 other voltages
# require no scaling
compute vid1 6.337*@ , @/6.337
@@ -707,7 +732,7 @@ chip "maxilife-cg-*"
ignore temp1
label temp3 "BX Temp"
label vid2 "Vcpu1"
label vid3 "Vcpu2"
ignore vid4
@@ -717,7 +742,7 @@ chip "maxilife-co-*"
label temp1 "CPU 1 Temp"
label temp3 "CPU 2 Temp"
label vid2 "Vcpu1"
label vid3 "Vcpu2"
label vid4 "VcacheL2"
@@ -760,16 +785,16 @@ chip "via686a-*"
# reflect what they say. Unfortunately, they are not at all specific about
# how to convert any of the register values to real units. Fortunately,
# Jonathan Yew <j.teh@iname.com> and Alex van Kaam <darkside@chello.nl>
# came through with some data for temp conversion and formulae for voltage
# conversion. However, the conversions should be regarded as our best guess-
# came through with some data for temp conversion and formulae for voltage
# conversion. However, the conversions should be regarded as our best guess-
# YMMV.
# On the Tyan S1598, the 2.5V sensor reads 0 and is not displayed in the BIOS.
# Linas Vepstas <linas@linas.org> reports that this sensor shows nothing of
# interest on the Abit KA7 (Athlon), and is also not displayed in the BIOS.
# Likewise, Johannes Drechsel-Burkhard <jdb@chello.at> reports that this
# sensor is unavailable in the BIOS of his MSI K7T Pro (Thunderbird). So,
# if you have one of these boards you may want to uncomment the 'ignore 2.5V'
# Likewise, Johannes Drechsel-Burkhard <jdb@chello.at> reports that this
# sensor is unavailable in the BIOS of his MSI K7T Pro (Thunderbird). So,
# if you have one of these boards you may want to uncomment the 'ignore 2.5V'
# line below.
label "2.0V" "CPU core"
@@ -784,20 +809,20 @@ chip "via686a-*"
# VIA suggests that temp3 is an internal temp sensor for the 686a. However,
# on the Tyan S1598 as well as the Abit KA7 (Athalon), the absolute values
# of the readings from that sensor are not valid. The readings do seem to
# correlate with temp changes, but the conversion factor may be quite
# of the readings from that sensor are not valid. The readings do seem to
# correlate with temp changes, but the conversion factor may be quite
# different from temp1 & temp2 (as noted above, VIA has not provided
# conversion info). So, you may wish to 'ignore temp3'.
# conversion info). So, you may wish to 'ignore temp3'.
# Johannes Drechsel-Burkhard <jdb@chello.at> notes that on his MSI K7T Pro,
# temp1 is the CPU temp and temp2 is the SYS temp.
# temp1 is the CPU temp and temp2 is the SYS temp.
label temp1 "SYS Temp"
label temp2 "CPU Temp"
label temp3 "SBr Temp"
#ignore temp3
# Set your CPU core limits here. For the other voltage sensors, the
# Set your CPU core limits here. For the other voltage sensors, the
# built-in defaults should be fine.
set in0_min 2.0
@@ -805,13 +830,13 @@ chip "via686a-*"
# Set your temp limits here. Remember, 'tempX_over' is the temp at which an
# alarm is triggered, and 'tempX_hyst' is the temp at which an alarm turns off.
# Setting tempX_hyst to a few degrees below the corresponding tempX_over
# prevents an oscillation between alarm on and off states. This kind of
# oscillation is known as hyteresis, thus the name. (You typically get the
# most serious and troublesome hysteresis when a sensor triggers something to
# Setting tempX_hyst to a few degrees below the corresponding tempX_over
# prevents an oscillation between alarm on and off states. This kind of
# oscillation is known as hyteresis, thus the name. (You typically get the
# most serious and troublesome hysteresis when a sensor triggers something to
# reduce the temp, thus creating a negative feedback loop. Even without that,
# we would still get some oscillation when the temp hovers around the limit
# due to noise.)
# we would still get some oscillation when the temp hovers around the limit
# due to noise.)
set temp1_hyst 40
set temp1_over 45
@@ -826,8 +851,8 @@ chip "via686a-*"
#set fan2_min 5000
# For at least one Tyan S1598, the following corrections make the sensors
# readings more in-line with the BIOS readings on boot. Try these, and
# adjust as necessary.
# readings more in-line with the BIOS readings on boot. Try these, and
# adjust as necessary.
#compute "2.0V" 1.02*@ , @/1.02
#compute "3.3V" 1.02*@ , @/1.02
@@ -836,7 +861,7 @@ chip "via686a-*"
chip "mtp008-*"
# The values below should be correct if you own a Tyan S1834D motherboard.
# If not, please contact us, so we can figure out better readings.
# FOR TYAN S2510 SEE END OF THIS SECTION.
@@ -875,12 +900,12 @@ chip "mtp008-*"
compute in5 (@ * 36 - 118.61) / 7, (118.61 + 7 * @) / 36
# examples for temperature limits
# set temp1_over 40
# set temp1_hyst 37
# set temp2_over 52
# set temp2_hyst 47
# set temp3_over 52
# set temp3_hyst 47
# set temp1_over 40
# set temp1_hyst 37
# set temp2_over 52
# set temp2_hyst 47
# set temp3_over 52
# set temp3_hyst 47
# End of standard mtp008 configuration
@@ -926,8 +951,8 @@ chip "mtp008-*"
# label fan3 "fan6"
# ignore temp1
# label temp2 "MB Temp"
# set temp2_over 52
# set temp2_hyst 47
# set temp2_over 52
# set temp2_hyst 47
# ignore temp3
chip "adm1025-*"
@@ -1280,11 +1305,11 @@ chip "fscpos-*"
# Fans
label fan1 "Fan1"
ignore fan2
ignore fan3
ignore fan2
ignore fan3
# Voltage
label volt12 "+12V"
label volt5 "+5V"
label voltbatt "+3.3V"
@@ -1353,7 +1378,7 @@ chip "vt1211-*" "vt8231-*"
#
# 1 for temp, 0 for volt.
# Sensor Voltage Mode Temp Mode config bit
# -------- ------------ --------- --------------
# -------- ------------ --------- --------------
# Reading 1 temp3
# UCH1/Reading2 in0 temp2 0x04 (4)
# UCH2 in1 temp4 0x08 (8)
@@ -1364,14 +1389,14 @@ chip "vt1211-*" "vt8231-*"
#
# set uch1-2 to temp mode, uch3-5 to voltage mode
#
ignore temp1
ignore temp1
ignore in6
set config 12
ignore in0
ignore in1
ignore temp5
ignore temp6
ignore temp7
ignore temp5
ignore temp6
ignore temp7
#
# label in0 "unused"
# label in1 "unused"
@@ -1387,7 +1412,7 @@ chip "vt1211-*" "vt8231-*"
label temp4 "MB2 Temp"
#
# All voltage calculations have the form
# ((@ * 100) - 3) / (K * 95.8), (@ * K * 0.958) + .03
# ((@ * 100) - 3) / (K * 95.8), (@ * K * 0.958) + .03
# where K = R2 / (R1 + R2).
# Use the following K values based on input voltage.
# This of course assumes the mobo has the resistors
@@ -1400,13 +1425,13 @@ chip "vt1211-*" "vt8231-*"
# 5.0 0.4167
# 12.0 0.1754
#
# compute in0 ((@ * 100) - 3) / (0.5952 * 95.8), (@ * 0.5952 * 0.958) + .03
# compute in1 ((@ * 100) - 3) / (0.8333 * 95.8), (@ * 0.8333 * 0.958) + .03
compute in2 ((@ * 100) - 3) / (0.5952 * 95.8), (@ * 0.5952 * 0.958) + .03
compute in3 ((@ * 100) - 3) / (0.4167 * 95.8), (@ * 0.4167 * 0.958) + .03
compute in4 ((@ * 100) - 3) / (0.1754 * 95.8), (@ * 0.1754 * 0.958) + .03
compute in5 ((@ * 100) - 3) / (0.6296 * 95.8), (@ * 0.6296 * 0.958) + .03
# compute in6 ((@ * 100) - 3) / (0.5952 * 95.8), (@ * 0.5952 * 0.958) + .03
# compute in0 ((@ * 100) - 3) / (0.5952 * 95.8), (@ * 0.5952 * 0.958) + .03
# compute in1 ((@ * 100) - 3) / (0.8333 * 95.8), (@ * 0.8333 * 0.958) + .03
compute in2 ((@ * 100) - 3) / (0.5952 * 95.8), (@ * 0.5952 * 0.958) + .03
compute in3 ((@ * 100) - 3) / (0.4167 * 95.8), (@ * 0.4167 * 0.958) + .03
compute in4 ((@ * 100) - 3) / (0.1754 * 95.8), (@ * 0.1754 * 0.958) + .03
compute in5 ((@ * 100) - 3) / (0.6296 * 95.8), (@ * 0.6296 * 0.958) + .03
# compute in6 ((@ * 100) - 3) / (0.5952 * 95.8), (@ * 0.5952 * 0.958) + .03
set vrm 9.1
# set in0_min 2.5 * 0.95