Create GA-880GA-UD3H.conf

configs/Gigabyte/GA-880GA-UD3H.conf

@@ -0,0 +1,116 @@
+# Configuration file for the Gigabyte GA-880GA-UD3H,
+# contributed by Clipo.
+# 2019-02-14 
+# Updates welcome.
+# 
+# Based on Gigabyte GA-870A-UD3.conf contributed by Gary Myers and Zeke Fast
+#
+#
+# CPU sensor
+
+chip "k10temp-*"
+
+   label temp1 "CPU Temp (K10)" 
+
+# Motherboard sensors
+
+chip "it8720-isa-*"
+
+### Voltages
+
+   label  in0  "Vcore"
+   label  in1  "DDR3 1.5V" # as labelled in the BIOS.
+   label  in2  "+3.3V"
+   label  in3  "+5V"     # Not shown in BIOS.
+   label  in4  "+12V"    # Not shown in BIOS
+   ignore in5		 # Ambiguous - ignoring.
+   ignore in6		 # Ambiguous - ignoring.
+   label  in7  "5VSB"    # Not shown in BIOS.
+   label  in8  "Vbat"    # Not shown in BIOS.
+   ignore cpu0_vid
+
+   # "Vcore", "DDR3 1.5V", "+3.3V" and "Vbat" are connected directly, so no compute
+   # line is needed for these. +5V and 5VSB are internal so we use the
+   # standard scaling factor. Scaling for +12V is apparently not standard
+   # this value was taken from the donor config file
+   # 
+   compute  in3  @ * (6.8/10+1), @ / (6.8/10+1)
+   compute  in4  @ * 3.963,      @ / 3.963
+   compute  in7  @ * (6.8/10+1), @ / (6.8/10+1)
+
+   # The BIOS will not set any limit for voltages.
+
+   set in0_min  0.825 * 0.95
+   set in0_max  1.425 * 1.05
+   set in1_min  1.5   * 0.95
+   set in1_max  1.5   * 1.05
+   set in2_min  3.3   * 0.95
+   set in2_max  3.3   * 1.05
+   set in3_min  5     * 0.95
+   set in3_max  5     * 1.05
+   set in4_min 12     * 0.95
+   set in4_max 12     * 1.05
+   set in7_min  5     * 0.95
+   set in7_max  5     * 1.05
+
+### Temperatures
+
+   label temp1 "System Temp"
+   # This sensor appears to be around or inside the ITE8720F chip.
+   set   temp1_min 0
+   set   temp1_max 40 
+
+   label temp2  "CPU Temp"
+   # This sensor can show 2 degrees difference to the K10 sensor.
+   # The end user can choose which one they prefer.
+   set   temp2_min 0
+   set   temp2_max 60 # Set to match your BIOS "CPU Warning Temperature"
+
+   label temp3 "Second CPU Temp?"
+   #This sensors appears to follow the CPU temp but with a large termal lag and slightly lower value
+   #
+   #set   temp3	# 
+
+### Fans
+
+   # Label based on motherboard connectors.
+   label fan1 "CPU Fan"		# M/B label: CPU_FAN (4-pin)
+   label fan5 "Power Fan"	# M/B label: PWR_FAN (3-pin)
+   label fan2 "System Fan 1"	# M/B label: SYS_FAN1 (3-pin)
+   label fan3 "System Fan 2"	# M/B label: SYS_FAN2 (3-pin)
+
+   # Minimum fan speeds.
+   # Comment/un-comment fan headers you are using if you want alarms.
+   set fan1_min 300	# CPU Fan
+   set fan5_min 300	# Power Fan
+   set fan2_min 300	# System Fan 1
+   set fan3_min 300     # System Fan 2
+
+# Original Sensors output before configuration applied
+#
+## it8720-isa-0228
+#Adapter: ISA adapter
+#in0:          +1.46 V  (min =  +0.00 V, max =  +4.08 V)
+#in1:          +1.49 V  (min =  +0.00 V, max =  +4.08 V)
+#in2:          +3.38 V  (min =  +0.00 V, max =  +4.08 V)
+#+5V:          +3.02 V  (min =  +0.00 V, max =  +4.08 V)
+#in4:          +3.09 V  (min =  +0.00 V, max =  +4.08 V)
+#in5:          +2.85 V  (min =  +0.00 V, max =  +4.08 V)
+#in6:          +4.08 V  (min =  +0.00 V, max =  +4.08 V)
+#5VSB:         +2.96 V  (min =  +0.00 V, max =  +4.08 V)
+#Vbat:         +3.02 V
+#fan1:         629 RPM  (min =   10 RPM)
+#fan2:         950 RPM  (min =   10 RPM)
+#fan3:        1315 RPM  (min =   10 RPM)
+#fan5:        1310 RPM  (min =   10 RPM)
+#temp1:        +26.0°C  (low  = +127.0°C, high = +127.0°C)  sensor = thermistor
+#temp2:        +32.0°C  (low  = +127.0°C, high = +60.0°C)  sensor = thermal diode
+#temp3:        +34.0°C  (low  = +127.0°C, high = +127.0°C)  sensor = thermistor
+#cpu0_vid:    +0.513 V
+#intrusion0:  ALARM
+#
+#k10temp-pci-00c3
+#Adapter: PCI adapter
+#temp1:        +32.9°C  (high = +70.0°C)
+#                       (crit = +79.0°C, hyst = +77.0°C)
+