mirror of
https://github.com/lm-sensors/lm-sensors.git
synced 2026-11-01 13:20:30 +00:00
Config for ASRock Z390M ITX
This is a configuration for an ASRock Z390M ITX/ac motherboard.
This commit is contained in:
Aaron Bockelie authored and aaronsb committed
1 parent
77e7a63086
commit
f9fc7d0d83
1 file changed
+162
@@ -0,0 +1,162 @@
|
||||
# Board: ASRock Z390M-ITX/ac
|
||||
# Contributed by: Aaron Bockelie
|
||||
# Processor: Intel(R) Core(TM) i7-8700 CPU @ 3.20GHz (6/158/10)
|
||||
# Board has connectors for buzzer and 3 fans (2 case + 1 CPU)
|
||||
# board does not have a connector for intrusion detection
|
||||
# dmesg: "nct6775: Found NCT6793D or compatible chip at 0x2e:0x290"
|
||||
|
||||
chip "nct6793-*"
|
||||
|
||||
# Cross referenced with ASRock A-Tuning Application on 6/29/2020
|
||||
# Install in Windows and see /Program Files (x86)/ASRock Utility/A-Tuning/Conf/Z390MITX.xml
|
||||
# There is also an NCT3933U on the board for measuring the PCH and VCCST voltages, but it
|
||||
# is not accessible due to no kernel driver for it.
|
||||
|
||||
# Referenced from NCT677xF (NCT6793D) Data Sheet Page 57
|
||||
# All the internal inputs of the ADC, AVSB, VBAT, 3VSB, and 3VCC utilize an integrated voltage
|
||||
# divider with both resistors equal to 34K, yielding a voltage one half of the power supply.
|
||||
# Vin = VCC * (34K/(34K+34K)=1.65V where VCC is set to 3.3V
|
||||
|
||||
# ID NCTSpec NCTDesc ASRock Utility Description
|
||||
# in0 index80 CPUVCORE CPU_INPUT_V (Interface IR35201)
|
||||
# in1 index81 VIN1 <none>
|
||||
# in2 index82 AVSB <none>
|
||||
# in3 index83 3VCC P3P3_V
|
||||
# in4 index84 VIN0 <none>
|
||||
# in5 N/A N/A N/A
|
||||
# in6 index86 VIN4 SIO3_V
|
||||
# in7 index87 3VSB <none>
|
||||
# in8 index88 VBAT <none>
|
||||
# in9 index89 VTT <none>
|
||||
# in10 index8a VIN5 <none>, SIO6_V
|
||||
# in11 index8b VIN6 <none>, SIO4_V
|
||||
# in12 index8c VIN2 P12_V, SIO1_V
|
||||
# in13 index8d VIN3 P5P0_V, SIO2_V
|
||||
# in14 index8e VIN7 SIO5_V
|
||||
|
||||
|
||||
set beep_enable 1
|
||||
|
||||
# voltages
|
||||
# The CPUVCORE pin feeds directly into the ADC with no voltage divider since the nominal
|
||||
# voltage on this pin is only 1.2V
|
||||
|
||||
label in0 "Vcore"
|
||||
compute in0 @*2, @/2
|
||||
set in0_min 0.16
|
||||
set in0_max 1.48
|
||||
set in0_beep 1
|
||||
|
||||
ignore in1
|
||||
|
||||
label in2 "AVCC"
|
||||
set in2_min 3.30 * 0.90
|
||||
set in2_max 3.30 * 1.10
|
||||
|
||||
label in3 "+3.3V"
|
||||
set in3_min 3.30 * 0.90
|
||||
set in3_max 3.30 * 1.10
|
||||
|
||||
ignore in4
|
||||
|
||||
ignore in5
|
||||
|
||||
ignore in6
|
||||
|
||||
label in7 "3VSB"
|
||||
set in7_min 3.30 * 0.90
|
||||
set in7_max 3.30 * 1.10
|
||||
|
||||
# This is the CMOS battery.
|
||||
|
||||
label in8 "VBATT"
|
||||
set in8_min 3.3 * 0.75
|
||||
set in8_max 3.3 * 1.10
|
||||
|
||||
label in9 "VTT"
|
||||
set in9_min 1.2 * 0.90
|
||||
set in9_max 1.2 * 1.25
|
||||
|
||||
ignore in10
|
||||
|
||||
ignore in11
|
||||
|
||||
label in12 "+12V"
|
||||
#((56+10)/10)
|
||||
compute in12 @*6.6, @/6.6
|
||||
set in12_min 12 * 0.95
|
||||
set in12_max 12 * 1.05
|
||||
|
||||
label in13 "+5V"
|
||||
compute in13 @*(24/8), @/(24/8)
|
||||
set in13_min 5 * 0.90
|
||||
set in13_max 5 * 1.10
|
||||
|
||||
ignore in14
|
||||
|
||||
|
||||
# temperatures
|
||||
# see NCT677xF (NCT6793D) Data Sheet Section 8.5.3.4 Temperature Reading
|
||||
# a customized nct6775 kernel driver is probably needed to reference the bank measurement method correctly
|
||||
# it appears that the temp sensor registers are off by one with the default driver
|
||||
# so SYSTIN is offset incorrectly and referenced as one of the AUXTIN values.
|
||||
|
||||
# I have interpeted the NCT spec as
|
||||
# ID NCTSpec Other Notes
|
||||
# temp1 SYSTIN Incorrect driver mapping of AUXTIN0
|
||||
# temp2 CPUTIN Actual CPU temperature verified physically
|
||||
# temp3 AUXTIN0 Actual motherboard temperature verified physically
|
||||
# temp4 AUXTIN1 Unused
|
||||
# temp5 AUXTIN2 Unused
|
||||
# temp6 AUXTIN3 Unused
|
||||
|
||||
ignore temp1
|
||||
|
||||
label temp2 "CPU"
|
||||
set temp2_max 85
|
||||
set temp2_max_hyst 50
|
||||
#set temp2_beep 1
|
||||
|
||||
label temp3 "MB"
|
||||
set temp3_max 75
|
||||
set temp3_max_hyst 50
|
||||
#set temp3_beep 1
|
||||
|
||||
ignore temp4
|
||||
|
||||
ignore temp5
|
||||
|
||||
ignore temp6
|
||||
|
||||
label temp7 "CPU_PECI"
|
||||
set temp7_max 85
|
||||
set temp7_max_hyst 50
|
||||
#set temp7_beep 1
|
||||
|
||||
ignore temp8
|
||||
ignore temp9
|
||||
ignore temp10
|
||||
|
||||
# fans
|
||||
# thankfully, fan PWM counters seem to function out of the box.
|
||||
# labels are based on the board documentation
|
||||
|
||||
label fan1 "Chassis_Fan_1/Pump"
|
||||
set fan1_min 300
|
||||
set fan1_beep 1
|
||||
|
||||
label fan2 "CPU_Fan_1"
|
||||
set fan2_min 600
|
||||
set fan2_beep 1
|
||||
|
||||
label fan5 "Chassis_Fan_2"
|
||||
set fan5_min 300
|
||||
set fan5_beep 1
|
||||
|
||||
# these are not on the mainboard
|
||||
ignore fan3
|
||||
ignore fan4
|
||||
|
||||
# misc
|
||||
#intrusion0 is actually available. When disabled in BIOS it returns OK
|
||||
ignore intrusion1
|
||||
Reference in new issue
Block a user