This driver is a copy of vt1211, which is almost identical.
The vt1211 is a super i/o chip and the vt8231 is a PCI chip.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1501 7894878c-1315-0410-8ee3-d5d059ff63e0
adding a rather large delay after resetting the device
via register 0x40. There is obviously a state machine
in the chip that takes a while to run after you reset it.
Figured out the delay time by trial and error.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1168 7894878c-1315-0410-8ee3-d5d059ff63e0
_sysctl_real
_register_entry
_proc_real
_detect
_deregister_entry
_chips_data
which were the global symbols renamed in i2c-proc.[ch] in the
i2c package.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1101 7894878c-1315-0410-8ee3-d5d059ff63e0
to force_addr. It is now consistent with the bus PCI adapters
that support base address setting (piix4, i801, viapro).
Other benefit is that via686a_find can now return -ENODEV,
and module will fail to load when base address is not set and
parameter is not used.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1073 7894878c-1315-0410-8ee3-d5d059ff63e0
Leave the files there for now.
Remove old installed sensors.o in kernel/Module.mk.
sensors.c was moved to i2c-proc.c in the i2c package.
i2c-isa.h was appended to i2c.h in the i2c package.
Delete all but the SYSCTL and ALARMS definitions in sensors.h,
as the rest of the file was moved to i2c-proc.h in the i2c package.
Remove #include "i2c-isa.h" lines in all chip drivers and
in bus driver i2c-isa.c.
This all probably breaks mkpatch.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@1015 7894878c-1315-0410-8ee3-d5d059ff63e0
address and program the base address in the 686a.
This is NOT a PCI force; the 3057 device must
be present in lspci.
Should work for Asus A7V/K7V boards which don't set the
base address (because they also have a as99127f on them!??).
Some rough edges remain, because
via686a_find() does not know there is a force; that only
is apparent to via686a_detect().
Notably, the driver will stay loaded even if the address is
uninitialized and there is no force; also, the driver complains
that a force is needed even when you give it one.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@999 7894878c-1315-0410-8ee3-d5d059ff63e0
the horrible
#if (LINUX_VERSION_CODE < KERNEL_VERSION(2,2,18)) || \
(LINUX_VERSION_CODE == KERNEL_VERSION(2,3,0))
They should now both work with 2.3 kernels (including 2.4 prepatches)
and very new 2.2 kernels (ie. 2.2.18 prepatches)
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@933 7894878c-1315-0410-8ee3-d5d059ff63e0
Mark D. Studebaker