There are now two new insmod parameters, and the #define has disappeared
force: if set to anything but zero, this enables the PIIX4 as the old
#define did.
force_addr: This first sets a new I/O port address for the PIIX4, and
afterwards enables it. Supercedes 'force'.
Note that using force_addr is very, very dangerous if you do not know
what you are doing. On the other hand, it was very easy to add, and can
be a big help if your BIOS doesn't set correct addresses.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@353 7894878c-1315-0410-8ee3-d5d059ff63e0
* Removed unnecessary MOD_INC/DEC_USE_COUNT in host adapter drivers
(i2c-via bit-lp bit-velle)
You can now rmmod adapters even when they have registered clients.
Without this, you would have to detach the clients first. Only way of doing
this is to rmmod the client drivers, but the same drivers might be used to
access clients behind other hosts.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@347 7894878c-1315-0410-8ee3-d5d059ff63e0
* Fixed i2c_probe to actually try some addresses, and
change the client->addr _only_ when we get a match.
* Algo-bit now scans the bus before registering it.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@346 7894878c-1315-0410-8ee3-d5d059ff63e0
is used but ignored (because the driver could not determine what
specific chip was there).
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@342 7894878c-1315-0410-8ee3-d5d059ff63e0
Also fixed a small lm78 problem and synchronised the detect script with
the Winbond detection.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@341 7894878c-1315-0410-8ee3-d5d059ff63e0
Also fixed a few nasty sensors.c bugs, and a minor LM78 one. If the new
parameters give trouble, please recompile sensors.c with DEBUG=1 and
examine the dmesg output!
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@338 7894878c-1315-0410-8ee3-d5d059ff63e0
The detection program can now be told that it should probe for more
addresses than the kernel driver module; it automatically generates
the necessary insmod parameters for the module if chips are found on
these non-standard addresses. Very useful for the LM78, for instance;
the driver still only check 0x20-0x2f, but the probe program checks
all addresses.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@336 7894878c-1315-0410-8ee3-d5d059ff63e0
Added RT table read to 781d but then #undef'ed it since it was just
all 1's. Changed max entries in sensor.c to 32 bytes to handle RT table.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@335 7894878c-1315-0410-8ee3-d5d059ff63e0
Improved bounds checking for FAN_TO_REG in all files.
For lm78-compatible drivers, minimum speed is 2657 RPM when the
divisor is 2. Attempts to set lower than that now are set to 0.
Before was set to a random number.
Thanks Jeff Dairiki.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@330 7894878c-1315-0410-8ee3-d5d059ff63e0
I've reviewed and applied the patch, but I would like some others to review
these commits too, to be safe.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@327 7894878c-1315-0410-8ee3-d5d059ff63e0
Supported insmod parameters:
ignore, ignore_range
probe, probe_range
force, force_lm78, force_lm78j, force_lm79
force* overrules ignore* overrules probe*
The *_range parameters need three elements for each specification:
bus,start_addr,end_addr
The address ranges are inclusive.
The other parameters need two elements for each specification:
bus,addr
In each case, '-1' stands for 'any I2C bus', and 9191 stands for
'the ISA bus' (Bonus question: who can figure out why I choose 9191?)
In each case, just append if you want several specification, for example:
insmod lm78 probe=9191,0x2a0,1,0x56
force_* does no detection, not even chip detection; it blindly assumes
you know what you are doing. plain force does the chip detection, but
nothing else; but it can still fail if the register read-out does not
match a chip type.
Detection is done in exactly the same way as sensors-detect, except that
only the range 0x20-0x2f is examined by default. This needs to be
synchronized somehow with the detect script. I would rather scan the whole
I2C address range, but with those clueless PIIX4 hangs when clock chips
are read, that would simply give too much trouble.
The detect script has slightly better ISA detection now, too.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@325 7894878c-1315-0410-8ee3-d5d059ff63e0
It is untested as of yet; but it compiled without problem. Next step: add
support to the chip modules.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@324 7894878c-1315-0410-8ee3-d5d059ff63e0
* Either Phil had not done a 'cvs update', or I forgot a 'cvs commit'; anyway,
the last changes to detect.pl have been ported to sensors-detect.
* Added a rule to the Makefile fragment to install it in $(SBINDIR).
* Added SBINDIR to the main Makefile.
* Deleted detect.pl
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@323 7894878c-1315-0410-8ee3-d5d059ff63e0
removed in1 and added in6 for 783s to keep compatibility
with 781d/782d. So 783s has no in1. sorry.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@313 7894878c-1315-0410-8ee3-d5d059ff63e0
Frodo Looijaard