There are now two new insmod parameters, and the #define has disappeared
force: if set to anything but zero, this enables the PIIX4 as the old
#define did.
force_addr: This first sets a new I/O port address for the PIIX4, and
afterwards enables it. Supercedes 'force'.
Note that using force_addr is very, very dangerous if you do not know
what you are doing. On the other hand, it was very easy to add, and can
be a big help if your BIOS doesn't set correct addresses.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@353 7894878c-1315-0410-8ee3-d5d059ff63e0
* Removed unnecessary MOD_INC/DEC_USE_COUNT in host adapter drivers
(i2c-via bit-lp bit-velle)
You can now rmmod adapters even when they have registered clients.
Without this, you would have to detach the clients first. Only way of doing
this is to rmmod the client drivers, but the same drivers might be used to
access clients behind other hosts.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@347 7894878c-1315-0410-8ee3-d5d059ff63e0
is used but ignored (because the driver could not determine what
specific chip was there).
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@342 7894878c-1315-0410-8ee3-d5d059ff63e0
Also fixed a small lm78 problem and synchronised the detect script with
the Winbond detection.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@341 7894878c-1315-0410-8ee3-d5d059ff63e0
Also fixed a few nasty sensors.c bugs, and a minor LM78 one. If the new
parameters give trouble, please recompile sensors.c with DEBUG=1 and
examine the dmesg output!
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@338 7894878c-1315-0410-8ee3-d5d059ff63e0
Added RT table read to 781d but then #undef'ed it since it was just
all 1's. Changed max entries in sensor.c to 32 bytes to handle RT table.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@335 7894878c-1315-0410-8ee3-d5d059ff63e0
Improved bounds checking for FAN_TO_REG in all files.
For lm78-compatible drivers, minimum speed is 2657 RPM when the
divisor is 2. Attempts to set lower than that now are set to 0.
Before was set to a random number.
Thanks Jeff Dairiki.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@330 7894878c-1315-0410-8ee3-d5d059ff63e0
I've reviewed and applied the patch, but I would like some others to review
these commits too, to be safe.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@327 7894878c-1315-0410-8ee3-d5d059ff63e0
Supported insmod parameters:
ignore, ignore_range
probe, probe_range
force, force_lm78, force_lm78j, force_lm79
force* overrules ignore* overrules probe*
The *_range parameters need three elements for each specification:
bus,start_addr,end_addr
The address ranges are inclusive.
The other parameters need two elements for each specification:
bus,addr
In each case, '-1' stands for 'any I2C bus', and 9191 stands for
'the ISA bus' (Bonus question: who can figure out why I choose 9191?)
In each case, just append if you want several specification, for example:
insmod lm78 probe=9191,0x2a0,1,0x56
force_* does no detection, not even chip detection; it blindly assumes
you know what you are doing. plain force does the chip detection, but
nothing else; but it can still fail if the register read-out does not
match a chip type.
Detection is done in exactly the same way as sensors-detect, except that
only the range 0x20-0x2f is examined by default. This needs to be
synchronized somehow with the detect script. I would rather scan the whole
I2C address range, but with those clueless PIIX4 hangs when clock chips
are read, that would simply give too much trouble.
The detect script has slightly better ISA detection now, too.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@325 7894878c-1315-0410-8ee3-d5d059ff63e0
It is untested as of yet; but it compiled without problem. Next step: add
support to the chip modules.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@324 7894878c-1315-0410-8ee3-d5d059ff63e0
removed in1 and added in6 for 783s to keep compatibility
with 781d/782d. So 783s has no in1. sorry.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@313 7894878c-1315-0410-8ee3-d5d059ff63e0
Added limit defaults for in7/in8 and added separate
782d/783s limit defaults for in5/in6.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@304 7894878c-1315-0410-8ee3-d5d059ff63e0
* No more redefined complaints of MODULE_* symbols for 2.0 kernels
This was introduced by the last archive of Simon
* Correct load order of adapters in detect script modprobe report
You can't assume things come out of a hash in the same order as you
put them in, of course :-(
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@303 7894878c-1315-0410-8ee3-d5d059ff63e0
Recognize chips, adjust /proc entries.
Added registers for Vbat/V5sb for 782d.
Did quick test that 781d isn't broken.
782d/783s untested, I'll send mail to the guy that volunteered.
No PWM fan support yet.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@297 7894878c-1315-0410-8ee3-d5d059ff63e0
Fan1 causes now alarm when rpm drops.
Fixed libsensors displaying incorrect temperature limits for rev 80.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@293 7894878c-1315-0410-8ee3-d5d059ff63e0
Code written by Ludovic Drolez (ldrolez@usa.net)
All voltages are now readable for the rev 00 but the read is blocked for 10
seconds because of the needed comparisons.
Currently voltages are readable in /proc only.
This functionality can be enabled at module-load with parameter readall:
insmod gl518 readall=1
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@289 7894878c-1315-0410-8ee3-d5d059ff63e0
device drivers. Specifically, I added these lines:
(in includes list)
#include "i2c-isa.h"
(Near beginning of *-attach-adapter function)
/* Make sure we aren't probing the ISA bus!! */
if (i2c_is_isa_adapter(adapter)) return 0;
This may be redundant is a couple of the files, but it shouldn't hurt.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@283 7894878c-1315-0410-8ee3-d5d059ff63e0
It compiles now cleanly against kernel 2.0.36; I checked, double-checked and
cross-checked.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@247 7894878c-1315-0410-8ee3-d5d059ff63e0
All our own code (ie. anything not in the i2c directory) compiles now without
warnings, even with WARN=1 (which sets -Wall -Wstrict-prototypes -Wshadow
-Wpointer-arith -Wcast-qual -Wcast-align -Wwrite-strings -Wnested-externs
-Winline). There is one exception: the lex code (conf-lex.l) complains about
unused functions. That's flex' fault, not ours!
The i2c code still emits many warnings with the above flags; that's Simon's
problem.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@233 7894878c-1315-0410-8ee3-d5d059ff63e0
Frodo Looijaard