Set DESTDIR if you want to install at some other place then where you
will run everything from.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@675 7894878c-1315-0410-8ee3-d5d059ff63e0
* Improved monitoring of /proc directories
Instead of doing:
proc_bus_i2c->fill_inode = &monitor_bus_i2c;
void monitor_bus_i2c(struct inode *inode, int fill)
{
if (fill)
MOD_INC_USE_COUNT;
else
MOD_DEC_USE_COUNT;
}
you can now simply set:
proc_bus_i2c->owner = THIS_MODULE;
and this is just as good!
* An old 2.3 problem seemingly never was resolved yet: instead of using
a *wait_queue directly, you have to use a wait_queue_head_t and
initialize it properly:
#if (LINUX_VERSION_CODE < 0x020301)
static struct wait_queue *pcf_wait = NULL;
#else
static wait_queue_head_t pcf_wait;
#endif
#if (LINUX_VERSION_CODE >= 0x020301)
init_waitqueue_head(&pcf_wait);
#endif
except for this, semantics remain the same (but using a plain
wait_queue_head_t instead of a pointer to a wait_queue)
* I had to change the semantics of sensors_register_entry slightly,
to make the monitoring of /proc/sys/dev/* files possible for kernels
2.3.27 and newer. It now takes an additional parameter, which you
can specify as THIS_MODULE.
* THIS_MODULE is only defined in kernels 2.3.13 and later; added
it to compat.h and the compatibility section of mkpatch.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@640 7894878c-1315-0410-8ee3-d5d059ff63e0
* Removed several superfluous (struct i2c_client *) casts (they were left
from the time we had separate structs for smbus and isa)
* Removed the internal lists of registered clients
They have not been used for quite some time now, took memory space,
and limited the maximum number of clients that could be registered.
Also removed two small Makefile errors - I am happy I caught them before
the next release!
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@582 7894878c-1315-0410-8ee3-d5d059ff63e0
The Makefile now examine $(LINUX)/.config to see what modules need to be
compiled. It compiles only those modules which were either not configured
in at all, or were built as modules (ie. drivers which are built-in in the
kernel are not built, as they can not be overruled).
The above is still potentially dangerous, if we break the interface of
our modules. Still, it is much better than it was.
C
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@575 7894878c-1315-0410-8ee3-d5d059ff63e0
Most important change: GL518SM-rev00 can't use kernel threads on 2.0 and
early 2.1 kernels
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@563 7894878c-1315-0410-8ee3-d5d059ff63e0
* mkpatch now correctly works when kernel-side files do not yet exist.
I forgot to propagate a change in the i2c version.
* __init* handling in mkpatch and compat.h
* New i801 defines added to mkpatch
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@545 7894878c-1315-0410-8ee3-d5d059ff63e0
* removed algorithm registration in i2c-isa
* renamed i2c-via2.o to i2c-viapro.o in the driver messages
* added detection for new drivers in sensors-detect script
* minor gl518sm fix
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@522 7894878c-1315-0410-8ee3-d5d059ff63e0
* gl518sm document simplified for rev 0x00 & 0x80
* gl518sm & gl520sm libsensors interface updates
BTW: Revision is no longer part of the name, so old sensors.conf
will not work at all with gl518sm.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@511 7894878c-1315-0410-8ee3-d5d059ff63e0
* i2c-isa simplified, by using the addr field in the client structure,
instead of a new field. This means we do not need `struct isa_*'
anymore
* All clients changed to reflect the new isa code. Many are much
simplified now.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@505 7894878c-1315-0410-8ee3-d5d059ff63e0
* The i2c package can no longer be compiled as part of the lm_sensors tree
* The archive of the i2c package is removed
* smbus, i2c-dev and i2c-proc modules and headers have been removed; they
are now completely integrated into the i2c package
* The fake i2c.h header has been removed; this also allowed us to remove
the ugly LM_SENSORS and TBD defines.
* A new variable I2C_HEADERS is introduced in the Makefile. This allows
us to install the i2c headers in, for example, /usr/local/include/linux.
* All files now include <linux/i2c.h> instead of "i2c.h" and "smbus.h"
Status: 'make dep' works, all the right include files are found. 'make all'
does not yet work.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@496 7894878c-1315-0410-8ee3-d5d059ff63e0
is right now, it should clear the LCD screen. But, I discovered that
the display simply can't cope with I2C read commands - it completely
locks up *both* the data and the *clock* lines! (That's new.) So,
it kills the bus when probes or other reads are done to the device.
Matrix-Orbital has to fix this before we can get anything
usable working. :'(
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@464 7894878c-1315-0410-8ee3-d5d059ff63e0
need these 'special' modelines for XF86Config:
ModeLine "640x480NTSC" 28.195793 640 656 658 784 480 520 525 600
ModeLine "800x600NTSC" 38.769241 800 812 814 880 600 646 649 735
My monitor really doesn't like these modes, but they seem to work well
for TV output. Oh, and this is only for a screen depth of 16bits
right now.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@459 7894878c-1315-0410-8ee3-d5d059ff63e0
Now prints out what kind of sensor it is.
Also separated alarms for temp2 and temp3 for 782d/783s (they are
a single bit for 781d).
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@400 7894878c-1315-0410-8ee3-d5d059ff63e0
The old documentation of Phil is still present at the bottom of the file.
Phil may decide to remove it.
In the driver, file 'status' is renamed to 'alarms' and masked to display
only the alarm bits. This fits more closely with other drivers, and the
remaining bit was not interesting anyway.
I fixed a problem that made insertion of the module impossible (I made a
typo when I introduced the insmod parameters) *** Someone else seems to
have changed this at almost the same moment?!? Now it is correct. ***
The MAX1617 and MAX1617A are now also supported by the library.
Once more, some slight formatting changes are made in the documentation
generators (some columns were made wider).
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@395 7894878c-1315-0410-8ee3-d5d059ff63e0
Whatever you cat to /proc/..../lm78-*/*, the result will now always be
sensible. No more overflows resulting in weird values.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@381 7894878c-1315-0410-8ee3-d5d059ff63e0
* sis5595.c now understand insmod parameters
* sis5595.c now uses sis5595_ prefix instead of lm78_ prefix
* sis5595.c now supports the correct subset of the LM78 features
(it only knows about 4 voltages, 2 fans and no vid)
* added SIS5595 defines to sensors.h
* fixed a small problem in compat.h
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@379 7894878c-1315-0410-8ee3-d5d059ff63e0
This new version also creates MODULE_PARM_DESC entries, which describe
what each parameter is used for.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@360 7894878c-1315-0410-8ee3-d5d059ff63e0
Added RT table read to 781d but then #undef'ed it since it was just
all 1's. Changed max entries in sensor.c to 32 bytes to handle RT table.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@335 7894878c-1315-0410-8ee3-d5d059ff63e0
I've reviewed and applied the patch, but I would like some others to review
these commits too, to be safe.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@327 7894878c-1315-0410-8ee3-d5d059ff63e0
Supported insmod parameters:
ignore, ignore_range
probe, probe_range
force, force_lm78, force_lm78j, force_lm79
force* overrules ignore* overrules probe*
The *_range parameters need three elements for each specification:
bus,start_addr,end_addr
The address ranges are inclusive.
The other parameters need two elements for each specification:
bus,addr
In each case, '-1' stands for 'any I2C bus', and 9191 stands for
'the ISA bus' (Bonus question: who can figure out why I choose 9191?)
In each case, just append if you want several specification, for example:
insmod lm78 probe=9191,0x2a0,1,0x56
force_* does no detection, not even chip detection; it blindly assumes
you know what you are doing. plain force does the chip detection, but
nothing else; but it can still fail if the register read-out does not
match a chip type.
Detection is done in exactly the same way as sensors-detect, except that
only the range 0x20-0x2f is examined by default. This needs to be
synchronized somehow with the detect script. I would rather scan the whole
I2C address range, but with those clueless PIIX4 hangs when clock chips
are read, that would simply give too much trouble.
The detect script has slightly better ISA detection now, too.
git-svn-id: http://lm-sensors.org/svn/lm-sensors/trunk@325 7894878c-1315-0410-8ee3-d5d059ff63e0
Mark D. Studebaker